Network Working Group ANSI X3S3.3 86-80 Request for Comments: 994 ISO TC97/SC6/N 3998 March 1986 I S O INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION ______________________________________________________________________ | | | ISO/TC 97/SC 6 | | TELECOMMUNICATIONS AND INFORMATION | | EXCHANGE BETWEEN SYSTEMS | | Secretariat: USA (ANSI) | | | | | |_____________________________________________________________________| Title: Final Text of DIS 8473, Protocol for Providing the Connectionless- mode Network Service Source: DIS 8473 Editor ISO 8473 [Page 1] RFC 994 December 1986 Contents 1 Scope and Field of Application 6 2 References 7 SECTION ONE. GENERAL 9 3 Definitions 9 3.1 Reference Model Definitions . . . . . . . . . . . . . . . . . 9 3.2 Service Conventions Definitions . . . . . . . . . . . . . . . 9 3.3 Network Layer Architecture Definitions . . . . . . . . . . . . 9 3.4 Network Layer Addressing Definitions . . . . . . . . . . . . . 10 3.5 Additional Definitions . . . . . . . . . . . . . . . . . . . . 10 4 Symbols and Abbreviations 11 4.1 Data Units . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.2 Protocol Data Units . . . . . . . . . . . . . . . . . . . . . 11 4.3 Protocol Data Unit Fields . . . . . . . . . . . . . . . . . . 11 4.4 Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.5 Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . 11 5 Overview of the Protocol 12 5.1 Internal Organization of the Network Layer . . . . . . . . . . 12 5.2 Subsets of the Protocol . . . . . . . . . . . . . . . . . . . 12 5.3 Addresses and Titles . . . . . . . . . . . . . . . . . . . . . 13 5.3.1 Addresses . . . . . . . . . . . . . . . . . . . . . . 13 5.3.2 Network-entity Titles . . . . . . . . . . . . . . . . 13 5.4 Service Provided by the Network Layer . . . . . . . . . . . . 14 5.5 Underlying Service Assumed by the Protocol . . . . . . . . . . 14 5.5.1 Subnetwork Points of Attachment . . . . . . . . . . . 15 5.5.2 Subnetwork Quality of Service . . . . . . . . . . . . 15 5.5.3 Subnetwork User Data . . . . . . . . . . . . . . . . 16 5.5.4 Subnetwork Dependent Convergence Functions . . . . . . 16 5.6 Service Assumed from Local Environment . . . . . . . . . . . . 16 SECTION TWO. SPECIFICATION OF THE PROTOCOL 18 6 Protocol Functions 18 6.1 PDU Composition Function . . . . . . . . . . . . . . . . . . . 18 6.2 PDU Decomposition Function . . . . . . . . . . . . . . . . . . 19 6.3 Header Format Analysis Function . . . . . . . . . . . . . . . 19 ISO 8473 [Page 2] RFC 994 December 1986 6.4 PDU Lifetime Control Function . . . . . . . . . . . . . . . . 20 6.5 Route PDU Function . . . . . . . . . . . . . . . . . . . . . . 20 6.6 Forward PDU Function . . . . . . . . . . . . . . . . . . . . . 21 6.7 Segmentation Function . . . . . . . . . . . . . . . . . . . . 21 6.8 Reassembly Function . . . . . . . . . . . . . . . . . . . . . 22 6.9 Discard PDU Function . . . . . . . . . . . . . . . . . . . . . 23 6.10 Error Reporting Function . . . . . . . . . . . . . . . . . . . 24 6.10.1 Overview . . . . . . . . . . . . . . . . . . . . . . . 24 6.10.2 Requirements . . . . . . . . . . . . . . . . . . . . . 25 6.10.3 Processing of Error Reports . . . . . . . . . . . . . 25 6.10.4 Relationship of Data PDU Options to Error Reports . . 26 6.11 PDU Header Error Detection . . . . . . . . . . . . . . . . . . 27 6.12 Padding Function . . . . . . . . . . . . . . . . . . . . . . . 28 6.13 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 6.14 Source Routing Function . . . . . . . . . . . . . . . . . . . 28 6.15 Record Route Function . . . . . . . . . . . . . . . . . . . . 29 6.16 Quality of Service Maintenance Function . . . . . . . . . . . 30 6.17 Priority Function . . . . . . . . . . . . . . . . . . . . . . 31 6.18 Congestion Notification Function . . . . . . . . . . . . . . . 31 6.19 Classification of Functions . . . . . . . . . . . . . . . . . 31 7 Structure and Encoding of PDUs 33 7.1 Structure . . . . . . . . . . . . . . . . . . . . . . . . . . 33 7.2 Fixed Part . . . . . . . . . . . . . . . . . . . . . . . . . . 34 7.2.1 General . . . . . . . . . . . . . . . . . . . . . . . 34 7.2.2 Network Layer Protocol Identifier . . . . . . . . . . 34 7.2.3 Length Indicator . . . . . . . . . . . . . . . . . . 35 7.2.4 Version/Protocol Identifier Extension . . . . . . . . 35 7.2.5 PDU Lifetime . . . . . . . . . . . . . . . . . . . . 35 7.2.6 Flags . . . . . . . . . . . . . . . . . . . . . . . . 35 7.2.6.1 Segmentation Permitted . . . . . . . . . . . 35 7.2.6.2 More Segments . . . . . . . . . . . . . . . 35 7.2.6.3 Error Report . . . . . . . . . . . . . . . 36 7.2.7 Type Code . . . . . . . . . . . . . . . . . . . . . . 36 7.2.8 PDU Segment Length . . . . . . . . . . . . . . . . . 36 7.2.9 PDU Checksum . . . . . . . . . . . . . . . . . . . . 36 7.3 Address Part . . . . . . . . . . . . . . . . . . . . . . . . 37 7.3.1 General . . . . . . . . . . . . . . . . . . . . . . . 37 7.3.1.1 Destination and Source Addresses . . . . . . 37 7.4 Segmentation Part . . . . . . . . . . . . . . . . . . . . . . 38 7.4.1 Data Unit Identifier . . . . . . . . . . . . . . . . . 38 7.4.2 Segment Offset . . . . . . . . . . . . . . . . . . . . 38 7.4.3 PDU Total Length . . . . . . . . . . . . . . . . . . . 39 7.5 Options Part . . . . . . . . . . . . . . . . . . . . . . . . 39 7.5.1 General . . . . . . . . . . . . . . . . . . . . . . . 39 7.5.2 Padding . . . . . . . . . . . . . . . . . . . . . . . 40 7.5.3 Security . . . . . . . . . . . . . . . . . . . . . . . 40 7.5.3.1 Source Address Specific . . . . . . . . . . 41 7.5.3.2 Destination Address Specific . . . . . . . . 41 7.5.3.3 Globally Unique Security . . . . . . . . . . 41 7.5.4 Source Routing . . . . . . . . . . . . . . . . . . . 41 ISO 8473 [Page 3] RFC 994 December 1986 7.5.5 Recording of Route . . . . . . . . . . . . . . . . . . 42 7.5.6 Quality of Service Maintenance . . . . . . . . . . . . 43 7.5.6.1 Source Address Specific . . . . . . . . . . 43 7.5.6.2 Destination Address Specific . . . . . . . . 43 7.5.6.3 Globally Unique QoS . . . . . . . . . . . . 43 7.5.7 Priority . . . . . . . . . . . . . . . . . . . . . . 44 7.6 Data Part . . . . . . . . . . . . . . . . . . . . . . . . . . 45 7.7 Data (DT) PDU . . . . . . . . . . . . . . . . . . . . . . . . 46 7.7.1 Structure . . . . . . . . . . . . . . . . . . . . . . 46 7.7.1.1 Fixed Part . . . . . . . . . . . . . . . . . . . . . 47 7.7.1.2 Addresses . . . . . . . . . . . . . . . . . . . . . 47 7.7.1.3 Segmentation . . . . . . . . . . . . . . . . . . . . 47 7.7.1.4 Options . . . . . . . . . . . . . . . . . . . . . . 47 7.7.1.5 Data . . . . . . . . . . . . . . . . . . . . . . . 47 7.8 Inactive Network Layer Protocol . . . . . . . . . . . . . . . 47 7.8.1 Network Layer Protocol Id . . . . . . . . . . . . . . 47 7.8.2 Data Field . . . . . . . . . . . . . . . . . . . . . 47 7.9 Error Report PDU (ER) . . . . . . . . . . . . . . . . . . . . 48 7.9.1 Structure . . . . . . . . . . . . . . . . . . . . . . 48 7.9.1.1 Fixed Part . . . . . . . . . . . . . . . . . 49 7.9.1.2 Addresses . . . . . . . . . . . . . . . . . 49 7.9.1.3 Options . . . . . . . . . . . . . . . . . . 49 7.9.1.4 Reason for Discard . . . . . . . . . . . . . 50 7.9.1.5 Error Report Data Field . . . . . . . . . . 51 8 Conformance 51 8.1 Provision of Functions for Conformance . . . . . . . . . . . . 51 List of Tables 1 Service Primitives for Underlying Service . . . . . . . . . . . . 14 2 Service Primitives for Underlying Service . . . . . . . . . . . . 14 3 Timer Primitives . . . . . . . . . . . . . . . . . . . . . . . . 14 4 Categorization of Protocol Functions . . . . . . . . . . . . . . . 32 5 Valid PDU Types . . . . . . . . . . . . . . . . . . . . . . . . . 36 6 Encoding of Option Parameters . . . . . . . . . . . . . . . . . . 39 7 Reason for Discard . . . . . . . . . . . . . . . . . . . . . . . . 50 8 Categorization of Functions . . . . . . . . . . . . . . . . . . . 52 List of Figures 1 Interrelationship of Standards . . . . . . . . . . . . . . . . . 6 2 PDU Structure . . . . . . . . . . . . . . . . . . . . . . . . . . 34 3 PDU Header -- Fixed Part . . . . . . . . . . . . . . . . . . . . . 34 4 PDU Header -- Address Part . . . . . . . . . . . . . . . . . . . 37 5 Address Parameters . . . . . . . . . . . . . . . . . . . . . . . . 38 6 PDU Header -- Segmentation Part . . . . . . . . . . . . . . . . . 38 7 PDU Header -- Options Part . . . . . . . . . . . . . . . . . . . . 39 8 PDU Header -- Data Field . . . . . . . . . . . . . . . . . . . . 45 ISO 8473 [Page 4] RFC 994 December 1986 9 DT PDU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 10 Inactive Network Layer Protocol . . . . . . . . . . . . . . . . . 47 11 Error Report PDU . . . . . . . . . . . . . . . . . . . . . . . . . 48 ISO 8473 [Page 5] RFC 994 December 1986 0 Introduction This Protocol Standard is one of a set of International Standards produced to facilitate the interconnection of open systems. The set of standards covers the services and protocols required to achieve such interconnection. This Protocol Standard is positioned with respect to other related standards by the layers defined in the Reference Model for Open Sys- tems Interconnection (ISO 7498). In particular, it is a protocol of the Network Layer. This Protocol may be used between network-entities in end systems or in Network Layer relay systems (or both). It pro- vides the Connectionless-mode Network Service as defined in Addendum 1 to the Network Service Definition Covering Connectionless-mode Transmission (ISO 8348/AD1). The interrelationship of these standards is illustrated in Figure 1 below: --------------------+--- ISO NETWORK SERVICE PROVIDER -----^----------------- | | | | | | PROTOCOL | REFERENCE TO AIMS -----------------+ | SPECIFICATION | REFERENCE TO ASSUMPTIONS -----------+ | | | | | | --------------------+---SUBNETWORK SERVICE DEFINITION(S)---v----------------- Figure 1: Interrelationship of Standards 1 Scope and Field of Application This International Standard specifies a protocol which is used to provide the Connectionless-mode Network Service as described in Ad- dendum 1 to the Network Service Definition Covering Connectionless- mode Transmission. The protocol relies upon the provision of an underlying connectionless-mode service by real subnetworks and/or data links. The underlying connectionless-mode service assumed by the protocol may be obtained either directly, from a connectionless-mode real subnetwork, or indirectly, through the operation of an appropri- ate Subnetwork Dependent Convergence Function (SNDCF) or Protocol (SNDCP) over a connection-mode real subnetwork as described in ISO 8648, Internal Organization of the Network Layer. ISO 8473 [Page 6] RFC 994 December 1986 This Standard specifies: a) procedures for the connectionless transmission of data and control information from one network-entity to a peer network-entity; b) the encoding of the protocol data units (PDUs) used for the transmission of data and control information, comprising a variable-length protocol header format; c) procedures for the correct interpretation of protocol control information; and d) the functional requirements for implementations claiming conformance to the Standard. The procedures are defined in terms of: a) the interactions among peer network-entities through the exchange of protocol data units; b) the interactions between a network-entity and a Network Service user through the exchange of Network Service primitives; and c) the interactions between a network-entity and an underlying service provider through the exchange of service primitives. 2 References ISO 7498, Information Processing Systems --- Open Systems Intercon- nection --- Basic Reference Model DIS 7498/AD1, Information Processing Systems --- Open Systems In- terconnection --- Addendum to ISO 7498 Covering Connectionless-mode Transmission ISO 8348, Information Processing Systems --- Telecommunications and Information Exchange between Systems --- Network Service Definition ISO 8348/AD1, Information Processing Systems --- Telecommunications and Information Exchange between Systems --- Addendum to the Net- work Service Definition Covering Connectionless-mode Transmission ISO 8348/AD2, Information Processing Systems --- Telecommunications and Information Exchange between Systems --- Addendum to the Net- work Service Definition Covering Network Layer Addressing* DIS 8648, Information Processing Systems --- Telecommunications and Information Exchange between Systems --- Internal Organization of the Network Layer ISO 8473 [Page 7] RFC 994 December 1986 ISO 8509, Technical Report --- OSI Service Conventions ISO 9074, A Formal Description Technique based on an Extended State Transition Model ________________________________ *At present, at the stage of Draft; publication anticipated in due course. ISO 8473 [Page 8] RFC 994 December 1986 SECTION ONE. GENERAL 3 Definitions 3.1 Reference Model Definitions This document makes use of the following concepts defined in ISO 7498: (a) End system (b) Network entity (c) Network layer (d) Network protocol (e) Network protocol data unit (f) Network relay (g) Network service (h) Network service access point (i) Network service access point address (j) Routing (k) Service (l) Service data unit 3.2 Service Conventions Definitions This Protocol Standard makes use of the following terms from the OSI Service Conventions Technical Report (ISO TR 8509): (a) Service provider (b) Service user 3.3 Network Layer Architecture Definitions This Protocol Standard makes use of the following terms from the Internal Organization of the Network Layer (ISO 8648): (a) Intermediate system (b) Relay system (c) Subnetwork ISO 8473 [Page 9] RFC 994 December 1986 3.4 Network Layer Addressing Definitions This Protocol Standard makes use of the following terms from ISO 8348/AD2, Addendum to the Network Service Definition Covering Network Layer addressing: (a) Network addressing domain (b) Network protocol address information (c) Subnetwork point of attachment 3.5 Additional Definitions For the purposes of this Protocol Standard, the following definitions apply: (a) derived PDU --- a protocol data unit whose fields are identical to those of an initial PDU, except that it carries only a segment of the user data from an N-UNITDATA request. (b) initial PDU --- a protocol data unit carrying the whole of the userq data from an N-UNITDATA request. (c) local matter --- a decision made by a system concerning its behavior in the Network Layer that is not prescribed or constrained by this Protocol Standard. (d) network-entity title --- an identifier for a network-entity which has the same abstract syntax as an NSAP address, and which can be used to unambiguously identify a network-entity in an end or intermediate system. (e) reassembly --- the act of regenerating an initial PDU from two or more derived PDUs. (f) segment --- a distinct unit of data consisting of part or all of the user data provided in the N-UNITDATA request and delivered in the N-UNITDATA indication. (g) segmentation --- the act of generating two or more derived PDUs from an initial or derived PDU. The derived PDUs together carry the entire user data of the initial or derived PDU from which they were generated. Note: It is possible that such an initial PDU will never actually be generated for a particular N-UNITDATA request, owing to the immediate application of segmentation. ISO 8473 [Page 10] RFC 994 December 1986 4 Symbols and Abbreviations 4.1 Data Units NSDU Network Service Data Unit PDU Protocol Data Unit SNSDU Subnetwork Service Data Unit 4.2 Protocol Data Units DT PDU Data Protocol Data Unit ER PDU Error Report Protocol Data Unit 4.3 Protocol Data Unit Fields CS Checksum DA Destination Address DAL Destination Address Length DUID Data Unit Identifier E/R Error Report Flag LI Length Indicator LT Lifetime MS More Segments Flag NLPID Network Layer Protocol Identifier SA Source Address SAL Source Address Length SL Segment Length SO Segment Offset SP Segmentation Permitted Flag TL Total Lengt TP Type V/P Version/Protocol Identifier Extension 4.4 Parameters DA Destination Address QOS Quality of Service SA Source Address 4.5 Miscellaneous CLNP Connectionless-mode Network Protocol NS Network Service NPAI Network Protocol Address Information NSAP Network Service Access Point SDU Service Data Uni SN Subnetwork SNDCF Subnetwork Dependent Convergence Function SNDCP Subnetwork Dependent Convergence Protocol SNICP Subnetwork Independent Convergence Protocol SNPA Subnetwork Point of Attachment ISO 8473 [Page 11] RFC 994 December 1986 5 Overview of the Protocol 5.1 Internal Organization of the Network Layer The architectural organization of the Network Layer is described in a separate document, Internal Organization of the Network Layer (ISO 8648). ISO 8648 identifies and categorizes the way in which functions can be performed within the Network Layer by Network Layer protocols, thus providing a uniform framework for describing how protocols operating either individually or cooperatively in the Network Layer can be used to provide the OSI Network Service. This protocol is designed to be used in the context of the internetworking protocol approach to the provision of the Connectionless-mode Network Service defined in that Standard. This protocol is intended for use in the Subnetwork Independent Con- vergence Protocol (SNICP) role. A protocol which fulfills the SNICP role operates to construct the OSI Network Service over a defined set of underlying services, performing functions which are necessary to support the uniform appearance of the OSI Connectionless-mode Network Service over a homogeneous or heterogeneous set of interconnected subnetworks. This protocol is defined to accommodate variability where Subnetwork Dependent Convergence Protocols and/or Subnetwork Access Protocols do not provide all of the functions necessary to support the Connectionless-mode Network Service over all or part of the path from one NSAP to another. As described in ISO 8648, a protocol at the Network Layer may fulfill different roles in different configurations. Although this protocol is designed particularly to be suitable for a SNICP role in the con- text of the internetworking protocol approach to the provision of the Connectionless-mode Network Service, it may also be used to fulfill other roles and may therefore be used in the context of other ap- proaches to subnetwork interconnection. The specification of this protocol begins with a definition of the underlying service which it assumes. This service is made available by the operation of other Network Layer protocols or through provi- sion of the Data Link Service. The underlying service assumed by this protocol is described in Clause 5.5. 5.2 Subsets of the Protocol Two proper subsets of the full protocol are defined which permit the use of known subnetwork characteristics and are therefore not subnet- work independent. The Inactive Network Layer protocol subset is a null-function subset which can be used when it is known that the source and destination end-systems are connected by a single subnetwork, and when none of the functions performed by the full protocol is required to provide ISO 8473 [Page 12] RFC 994 December 1986 the Connectionless-mode Network Service between any pair of end- systems. The Non-segmenting protocol subset permits simplification of the header where it is known that the source and destination end-systems are connected by subnetworks whose service data unit sizes are greater than or equal to a known bound which is large enough so that segmentation is not required. This subset is selected by setting the Segmentation Permitted flag to zero. 5.3 Addresses and Titles The following Clauses describe the addresses and titles used by this Protocol. 5.3.1 Addresses The Source Address and Destination Address parameters referred to in Clause 7.3 of this International Standard are OSI Network Service Ac- cess Point Addresses. The syntax and semantics of an OSI Network Service Access Point Address are described in a separate document, ISO 8348/AD2, Addendum to the Network Service Definition Covering Network Layer Addressing. The encoding used by this protocol to convey NSAP Addresses shall be the preferred binary encoding specified in ISO 8348/AD2; the entire NSAP address, taken as a whole, is represented explicitly as a string of binary octets. This string is conveyed in its entirety in the ad- dress fields described in Clause 7.3. The rules governing the genera- tion of the preferred binary encoding are described in ISO 8348/AD2. 5.3.2 Network-entity Titles A network-entity title is an identifier for a network-entity in an endsystem or intermediate-system. Network-entity titles are allocated from the same name space as NSAP addresses, and the determination of whether an address is an NSAP address or a network-entity title depends on the context in which the address is interpreted. The en- tries in the Source Routing and Recording of Route parameters defined in Clauses 7.5.4 and 7.5.5 are network-entity titles. The Source Ad- dress and Destination Address parameters in the Error Report PDU de- fined in Clause 7.9.1.2 are also network-entity titles. The encoding used by this protocol to convey network-entity titles shall also be the preferred binary encoding; again, the entire network-entity title, taken as a whole, is represented explicitly as a string of binary octets. This string is conveyed in its entirety in the fields described in Clauses 7.5.4, 7.5.5, and 7.9.1.2. ISO 8473 [Page 13] RFC 994 December 1986 5.4 Service Provided by the Network Layer The service provided by this protocol is the Connectionless-mode Net- work Service described in ISO 8348/AD1, Addendum to the Network Ser- vice Definition Covering Connectionless-mode Transmission. The Net- work Service primitives provided are summarized in Table 1: _____________________________________________________________ | PRIMITIVES PARAMETERS | |____________________________________________________________ | | N_UNITDATA .Request | N_Source_Address, | | .Indication | N_Destination_Address, | | | N_Quality_of_Service, | | | N_Userdata | |_________________________________|___________________________| Table 1: Service Primitives for Underlying Service The Addendum to the Network Service Definition Covering Connectionless-mode Transmission (ISO 8348/AD1) states that the max- imum size of a connectionless-mode Network-service-data-unit (NSDU) is limited to 64512 octets. 5.5 Underlying Service Assumed by the Protocol The underlying service required to support this protocol is defined by the following primitives: _____________________________________________________________ | PRIMITIVES PARAMETERS | |____________________________________________________________ | | SN_UNITDATA .Request | SN_Source_Address, | | .Indication | SN_Destination_Address, | | | SN_Quality_of_Service, | | | SN_Userdata | |_________________________________|___________________________| Table 2: Service Primitives for Underlying Service Note: These service primitives are used to describe the abstract interface which exists between the ISO 8473 protocol machine and an underlying real subnetwork or a Subnetwork Dependent Convergence Function which operates over a real subnetwork or real data link to provide the required underlying service. ISO 8473 [Page 14] RFC 994 December 1986 5.5.1 Subnetwork Points of Attachment The source and destination addresses specify the points of attachment to a public or private subnetwork(s) involved in the transmission. Subnetwork Point of Attachment addresses (SNPAs) are defined by each individual subnetwork authority. The syntax and semantics of SNPAs are not defined in this Standard. 5.5.2 Subnetwork Quality of Service Subnetwork Quality of Service describes aspects of an underlying connectionless-mode service which are attributable solely to the underlying service. Associated with each connectionless-mode transmission, certain meas- ures of Quality of Service are requested when the primitive action is initiated. These requested measures (or parameter values and op- tions) are based on a priori knowledge of the service(s) made avail- able to it by the subnetwork. Knowledge of the nature and type of service available is typically obtained prior to an invocation of the underlying connectionless-mode service. The Quality of Service parameters identified for the underlying connectionless-mode service may in some circumstances be directly derivable from or mappable onto those identified in the Connectionless-mode Network Service. The following parameters as de- fined in ISO 8348/AD1, Addendum to the Network Service Definition Covering Connectionlessmode Transmission, may be employed: (a) transit delay; (b) protection against unauthorized access; (c) cost determinants; (d) priority; and (e) residual error probability. Note: For those subnetworks which do not inherently provide Quality of Service as a parameter when the primitive action is initiated, it is a local matter as to how the semantics of the service requested might be preserved. In particular, there may be instances in which the Quality of Service requested cannot be maintained. In such circumstances, an attempt shall be made to deliver the protocol data unit at whatever Quality of Service is available. ISO 8473 [Page 15] RFC 994 December 1986 5.5.3 Subnetwork User Data The SN-Userdata is an ordered multiple of octets, and is transferred transparently between the specified subnetwork points of attachment. The underlying service assumed by the CLNP is required to support a service data unit size of at least 512 octets. If the minimum service data unit sizes supported by all of the sub- networks involved in the transmission of a particular PDU are known to be large enough that segmentation is not required, then the Non- segmenting protocol subset may be used. 5.5.4 Subnetwork Dependent Convergence Functions Subnetwork Dependent Convergence Functions may be performed to pro- vide an underlying connectionless-mode service in the case where a real subnetwork does not inherently provide the connectionless-mode service assumed by the protocol. If a subnetwork inherently provides a connection-mode service, a Subnetwork Dependent Convergence Func- tion provides a mapping into the required underlying service. Sub- network Dependent Convergence Functions may also be required in those cases where functions assumed from the underlying service are not performed. In some cases, this may require the operation of an ex- plicit protocol (i.e., a protocol involving explicit exchanges of protocol control information between peer network-entities) in the Subnetwork Dependent Convergence Protocol (SNDCP) role. However, there may also be cases where the functionality required to fulfill the SNDCP role consists simply of a set of rules for manipulating the underlying service. 5.6 Service Assumed from Local Environment A timer service must be provided to allow the protocol entity to schedule events. There are three primitives associated with the S-TIMER service: 1. the S--TIMER Request, 2. the S--TIMER Response, and 3. the S--TIMER Cancel. The S--TIMER Request primitive indicates to the local environment that it should initiate a timer of the specified name and subscript and maintain it for the duration specified by the time parameter. The S--TIMER Response primitive is initiated by the local environment to indicate that the delay requested by the corresponding S-TIMER Re- quest primitive has elapsed. ISO 8473 [Page 16] RFC 994 December 1986 The S--TIMER Cancel primitive is an indication to the local environ- ment that the specified timer(s) should be canceled. If the subscript parameter is not specified, then all timers with the specified name are canceled; otherwise, the timer of the given name and subscript is cancelled. If no timers correspond to the parameters specified, the local environment takes no action. The parameters of the S--TIMER service primitives are specified in Table 3. __________________________________________________ | PRIMITIVES PARAMETERS | |_________________________________________________| | S--TIMER .Request | S-Time, | | | S-Name, | | | S-Subscript | | | | | .Response | S-Name, | | | S-Subscript | |___________________________|_____________________| Table 3: Timer Primitives The time parameter indicates the time duration of the specified ti- mer. An identifiying label is associated with a timer by means of the name parameter. The subscript parameter specifies a value to dis- tinguish timers with the same name. The name and subscript taken to- gether constitute a unique reference to the timer. Timers used in association with a specific protocol funtion are de- fined under that protocol function. Note: This International Standard does not define specific values for the timers. Any derivations described in this Standard are not mandatory. Timer values should be chosen so that the requested Quality of Service can be provided, given the known characteristics of the underlying service. ISO 8473 [Page 17] RFC 994 December 1986 SECTION TWO. SPECIFICATION OF THE PROTOCOL 6 Protocol Functions This Clause describes the functions performed as part of the Proto- col. Not all of the functions must be performed by every implementation. Clause 6.17 specifies which functions may be omitted, and the correct behavior when requested functions are not implemented. 6.1 PDU Composition Function This function is responsible for the construction of a protocol data unit according to the rules governing the encoding of PDUs given in Clause 7. Protocol Control Information required for delivering the data unit to its destination is determined from current state and lo- cal information and from the parameters associated with the N- UNITDATA Request. Network Protocol Address Information (NPAI) for the Source Address and Destination Address fields of the PDU header is derived from the NS-Source-Address and NS-Destination-Address parameters. The NS- Destination-Address and NS-Quality-of-Service parameters, together with current state and local information, are used to determine which optional functions are to be selected. User data passed from the Net- work Service User (NS-Userdata) forms the Data field of the protocol data unit. During the composition of the protocol data unit, a Data Unit Iden- tifier is assigned to distinguish this request to transmit NS- Userdata to a particular destination NS User from other such re- quests. The originator of the PDU must choose the Data Unit Identif- ier so that it remains unique (for this Source and Destination ad- dress pair) for the maximum lifetime of the Initial PDU in the net- work; this rule applies for any PDUs derived from the Initial PDU as a result of the application of the Segmentation Function (see Clause 6.7). Derived PDUs are considered to correspond to the same Initial PDU, and hence the same N-UNITDATA Request, if they have the same Source Address, Destination Address, and Data Unit Identifier. The Data Unit Identifier is also available for ancillary functions such as error reporting (see Clause 6.10). The total length of the PDU in octets is determined by the originator and placed in the Total Length field of the PDU header. This field is not changed in any Derived PDU for the lifetime of the protocol data unit. ISO 8473 [Page 18] RFC 994 December 1986 When the Non-segmenting protocol subset is employed, neither the To- tal Length field nor the Data Unit Identifier field is present. The rules governing the PDU composition function are modified in this case as follows. During the composition of the protocol data unit, the total length of the PDU in octets is determined by the originator and placed in the Segment Length field of the PDU header. This field is not changed for the lifetime of the PDU. No Data Unit Identifica- tion is provided. 6.2 PDU Decomposition Function This function is responsible for removing the Protocol Control Infor- mation from the protocol data unit. During this process, information pertinent to the generation of the N-UNITDATA Indication is deter- mined as follows. The NS-Source-Address and NS-Destination-Address parameters of the N-UNITDATA Indication are recovered from the NPAI in the Source and Destination Address fields of the PDU header. The data field of the PDU received is reserved until all segments of the original service data unit have been received; collectively, these form the NS-Userdata parameter of the N-UNITDATA Indication. Infor- mation relating to the Quality of Service provided during the transmission of the PDU is determined from the Quality of Service and other information contained in the Options Part of the PDU header. This information constitutes the NS-Quality-of-Service parameter of the N-UNITDATA Indication. 6.3 Header Format Analysis Function This function determines whether the full protocol described in this Standard is employed, or one of the defined proper subsets thereof. If the protocol data unit has a Network Layer Protocol Identifier in- dicating that this is a standard version of the Protocol, this func- tion determines whether a received PDU has reached its destination, using the Destination Address provided in the PDU. If the Destination Address provided in the PDU identifies an NSAP served by this network-entity, then the PDU has reached its destination; if not, it must be forwarded. If the protocol data unit has a Network Layer Protocol Identifier in- dicating that the Inactive Network Layer Protocol subset is in use, then no further analysis of the PDU header is required. The network- entity in this case determines that either the Subnetwork Point of Attachment address encoded as network protocol address information in the supporting subnetwork protocol corresponds directly to an NSAP address serviced by this network-entity or that an error has oc- curred. If the subnetwork protocol data unit has been delivered correctly, then the PDU may be decomposed according to the procedures described for that particular subnetwork protocol. ISO 8473 [Page 19] RFC 994 December 1986 6.4 PDU Lifetime Control Function This function is used to enforce the maximum PDU lifetime. It is closely associated with the Header Format Analysis function. This function determines whether a PDU received may be forwarded or wheth- er its assigned lifetime has expired, in which case it must be dis- carded. The operation of the PDU Lifetime Control function depends upon the Lifetime field in the PDU header. This field contains, at any time, the remaining lifetime of the PDU (represented in units of 500 mil- liseconds). The Lifetime of the Initial PDU is determined by the ori- ginating network-entity, and placed in the Lifetime field of the PDU. When the Segmentation function is applied to a PDU, the value of the Lifetime field of the Initial PDU is copied into all of the Derived PDUs. The Lifetime of the PDU is decremented by every network-entity which processes the PDU. When a network-entity processes a PDU, it decre- ments the PDU Lifetime by at least one. The value of the PDU Life- time field shall be decremented by more than one if the sum of: 1. the transit delay in the underlying service from which the PDU was received; and 2. the delay within the system processing the PDU exceeds or is estimated to exceed 500 milliseconds. In this case, the lifetime field should be decremented by one for each additional 500 milliseconds of delay. The determination of delay need not be precise, but where a precise value cannot be ascertained, the value used shall be an overestimate, not an underestimate. If the Lifetime field reaches a value of zero before the PDU is delivered to the destination, the PDU must be discarded. The Error Reporting function shall be invoked as described in Clause 6.10, Er- ror Reporting Function, and may result in the generation of an Error Report PDU. It is a local matter whether the destination network- entity performs the Lifetime Control function. 6.5 Route PDU Function This function determines the network-entity to which a protocol data unit should be forwarded and the underlying service that must be used to reach that network-entity, using the Destination Address and the total length of the PDU. Where segmentation is required, the Route PDU function further determines over which underlying service Derived PDUs/segments must be sent in order to reach that network-entity. The results of the Route PDU function are passed to the Forward PDU func- tion (along with the PDU itself) for further processing. Selection of the underlying service that must be used to reach the "next" sys- ISO 8473 [Page 20] RFC 994 December 1986 tem in the route is initially influenced by the NS-Quality-of- Ser- vice parameter of the N-UNITDATA Request, which specifies the QoS re- quested by the sending NS User. Whether this QoS is to be provided directly by the CLNP, through the selection of the Quality of Service Maintenance parameter and other optional parameters, or through the QoS facilities offered by each of the underlying services is deter- mined prior to invocation of the Forward PDU function. Route selec- tion by intermediate systems may subsequently be influenced by the values of the Quality of Service Maintenance parameter (if present), and other optional parameters (if present). 6.6 Forward PDU Function This function issues an SN-UNITDATA Request primitive (see Clause 5.5), supplying the subnetwork or SNDCF identified by the Route PDU function with the protocol data unit as user data to be transmitted, the address information required by that subnetwork or SNDCF to iden- tify the "next" system within the subnetwork-specific addressing domain (this may be an intermediate-system or the destination end- system), and Quality of Service constraints (if any) to be considered in the processing of the user data. When the PDU to be forwarded is longer than the maximum service data user size provided by the underlying service, the Segmentation func- tion is applied (See Clause 6.7, which follows). 6.7 Segmentation Function Segmentation is performed when the size of the protocol data unit is greater than the maximum service data unit size supported by the underlying service to be used to transmit the PDU. Segmentation consists of composing two or more new PDUs (Derived PDUs) from the PDU received. The PDU received may be the Initial PDU, or it may be a Derived PDU. All of the header information from the PDU to be segmented, with the exception of the segment length and checksum fields of the fixed part, and the segment offset of the seg- mentation part, is duplicated in each Derived PDU, including all of the address part, the data unit identifier and total length of the segmentation part, and the options part (if present). Note: The rules for forwarding and segmentation guarantee that the header length is the same for all segments (Derived PDUs) of the Initial PDU, and is the same as the header length of the Initial PDU. The size of a PDU header will not change due to operation of any protocol function. The user data encapsulated within the PDU received are divided such that the Derived PDUs satisfy the size requirements of the user data parameter field of the primitive used to access the underlying ser- ISO 8473 [Page 21] RFC 994 December 1986 vice. Derived PDUs are identified as being from the same Initial PDU by means of (a) the source address, (b) the destination address, and (c) the data unit identifier. Segmentation shall not result in the generation of a Derived PDU con- taining less than eight (8) octets of user data. The following fields of the PDU header are used in conjunction with the Segmentation function: (a) Segment Offset --- identifies, with respect to the start of the Initial PDU, the octet at which the segment begins; (b) Segment Length --- specifies the number of octets in the Derived PDU, including both header and data; (c) More Segments Flag --- is set to one if this Derived PDU does not contain, as its final octet of user data, the final octet of the Initial PDU; and (d) Total Length --- specifies the entire length of the Initial PDU, including both header and data. Derived PDUs may be further segmented without constraining the rout- ing of the individual Derived PDUs. The Segmentation Permitted flag is set to one to indicate that segmentation is permitted. If the Ini- tial PDU is not to be segmented at any point during its lifetime in the network, the flag is set to zero by the source network-entity. The setting of the Segmentation Permitted flag cannot be changed by any other network-entity for the lifetime of the Initial PDU and any Derived PDUs. 6.8 Reassembly Function The Reassembly function reconstructs the Initial PDU from the Derived PDUs generated by the operation of the Segmentation Function on the Initial PDU (and, recursively, on subsequent Derived PDUs). A bound on the time during which segments (Derived PDUs) of an Initial PDU will be held at a reassembly point before being discarded is provid- ed, so that reassembly resources may be released when it is no longer expected that any outstanding segments of the Initial PDU will arrive at the reassembly point. Upon reception of a Derived PDU, a reassem- bly timer is initiated with a value which indicates the amount of ISO 8473 [Page 22] RFC 994 December 1986 time which must elapse before any outstanding segments of the Initial PDU shall be assumed to be lost. When this timer expires, all seg- ments (Derived PDUs) of the Initial PDU held at the reassembly point are discarded, the resources allocated for those segments are freed, and if selected, an Error Report is generated (see Clause 6.10). While the exact relationship between reassembly lifetime and PDU lifetime is a local matter, the Reassembly Function must preserve the intent of the PDU lifetime. Consequently, the reassembly function must discard PDUs whose lifetime would otherwise have expired had they not been under the control of the reassembly function. Note: 1. Methods of bounding reassembly lifetime are discussed in Annex B. 2. The Segmentation and Reassembly functions are intended to be used in such a way that the fewest possible segments are generated at each segmentation point and reassembly takes place at the final destination of a PDU. However, other schemes which (a) interact with the routing algorithm to favor paths on which fewer segments are generated; (b) generate more segments than absolutely required in order to avoid additional segmentation at some subsequent point; or (c) allow partial or full reassembly at some intermediate point along the route are not precluded. The information necessary to enable the use of one of these alternative strategies may be made available through the operation of a Network Layer Management function or by other means. 3. The originator of the Initial PDU determines the value of the Segmentation Permitted flag in the Initial PDU and all Derived PDUs (if any). Partial or full reassembly in an intermediate system (Note 2 (c) above) cannot change this value in the Initial PDU or any PDU derived from it, and cannot therefore add or remove the segmentation part of the header. 6.9 Discard PDU Function This function performs all of the actions necessary to free the resources reserved by the network-entity when any of the following situations is encountered (Note: the list is not exhaustive): (a) A violation of protocol procedure has occurred. ISO 8473 [Page 23] RFC 994 December 1986 (b) A PDU is received whose checksum is inconsistent with its contents. (c) A PDU is received, but due to local congestion, it cannot be processed. (d) A PDU is received whose header cannot be analyzed. (e) A PDU is received which cannot be segmented and cannot be forwarded because its length exceeds the maximum service data unit size supported by any underlying service available for transmission of the PDU to the next network-entity on the chosen route. (f) A PDU is received whose destination address is unreachable or unknown. (g) Incorrect or invalid source routing was specified. This may include a syntax error in the source routing field, an unknown or unreachable address in the source routing field, or a path which is not acceptable for other reasons. (h) A PDU is received whose PDU lifetime has expired or whose lifetime expires during reassembly. (i) A PDU is received which contains an unsupported option. 6.10 Error Reporting Function 6.10.1 Overview This function causes an attempt to return an Error Report PDU to the source network-entity when a protocol data unit is discarded in ac- cordance with Clause 6.9. The Error Report PDU identifies the discarded PDU, specifies the type of error detected, and identifies the location in the header of the discarded PDU at which the error was detected. At least the entire header of the Discarded PDU (and, at the discretion of the originator of the Error Report PDU none, all, or part of the data field) is placed in the data field of the Error Report PDU. The originator of a Data PDU may control the generation of Error Re- port PDUs. An Error Report flag in the original PDU is set by the source network-entity to indicate that an Error Report PDU is to be returned if the Initial PDU or any PDUs derived from it are discard- ed; if the flag is not set, Error Reports are to be suppressed. Note: 1. The suppression of Error Report PDUs is controlled by the ISO 8473 [Page 24] RFC 994 December 1986 originating network-entity and not by the NS User. Care should be exercised by the originator with regard to suppressing ER PDUs so that error reporting is not suppressed for every PDU generated. 2. Non-receipt of an Error Report PDU does not imply correct delivery of a PDU issued by a source network-entity. 6.10.2 Requirements An Error Report PDU shall not be generated to report the discard of an Error Report PDU. An Error Report PDU shall not be generated to report the discard of a Data PDU unless that PDU has the Error Report flag set to allow Error Reports. If a Data PDU is discarded, and the Error Report flag has been set to allow Error Reports, an Error Report PDU shall be generated if the reason for discard is one of the reasons for discard enumerated in Clause 6.9, subject to the conditions described in Clause 6.10.4. Note: If a Data PDU with the E/R flag set to allow Error Reports is discarded for any other reason, an ER PDU may be generated (as an implementation option). 6.10.3 Processing of Error Reports An Error Report PDU is composed from information contained in the header of the discarded Data PDU to which the Error Report refers. The contents of the Source Address field of the discarded Data PDU are used as the Destination Address of the Error Report PDU. This value, which in the context of the Data PDU was used as an NSAP Ad- dress, is used in the context of the Error Report PDU as the network-entity title of the network-entity that originated the Data PDU. The network- entity title of the originator of the Error Report PDU is conveyed in the Source Address field of the header of the Er- ror Report PDU. The value of the Lifetime field is determined in ac- cordance with Clause 6.4. Optional parameters are selected in accor- dance with Clause 6.10.4. Segmentation of Error Report PDUs is not permitted; hence, no Segmen- tation Part is present. The total length of the ER PDU in octets is placed in the Segment Length field of the ER PDU header. This field is not changed during the lifetime of the ER PDU. If the originator of the ER PDU determines that the size of the ER PDU exceeds the max- imum service data unit size of the underlying service, the ER PDU shall be truncated to the maximum service data unit size (see Clause 5.5.3) and forwarded with no other change. Error Report PDUs are routed and forwarded by intermediate-system network-entities in the ISO 8473 [Page 25] RFC 994 December 1986 same way as Data PDUs. Note: The requirement that the underlying service assumed by the CLNP must be capable of supporting a service data unit size of at least 512 octets guarantees that the entire header of the discarded Data PDU can be conveyed in the data field of any ER PDU. When an ER PDU is decomposed upon reaching its destination, informa- tion that may be used to interpret and act upon the Error Report is obtained as follows. The network-entity title recovered from the NPAI in the Source Address field of the ER PDU header is used to identify the network-entity which generated the Error Report. The reason for generating the Error Report is extracted from the Options Part of the PDU header. The entire header of the discarded Data PDU (and part or all of the original user data) is extracted from the data field of the ER PDU to assist in determining the nature of the error. 6.10.4 Relationship of Data PDU Options to Error Reports The generation of an Error Report is affected by options that are present in the corresponding Data PDU. The presence of options in the original Data PDU that are not supported by the system which has dis- carded that PDU may cause the suppression of an Error Report even if the original Data PDU indicated that an Error Report should be gen- erated in the event of a discard. The processing of an Error Report is also affected by options which are present in the corresponding Data PDU. In particular, options selected for the original Data PDU affect which options are included in the corresponding Error Report PDU. The selection of options for an Error Report PDU is governed by the following requirements: (a) If the Priority Option or the QoS Maintenance Option is selected in the original Data PDU, and the system generating the Error Report PDU supports the option, then the Error Report PDU shall specify the option. (b) If the Security Option is selected in the Data PDU, and the system generating the Error Report supports this option, then the Error Report PDU shall specify the option using the value that was specified in the original Data PDU. If the system does not support the Security Option, an Error Report must not be generated for a Data PDU that selects the Security Option. (c) If the Complete Source Route Option is selected in the original Data PDU, and the system generating the Error Report PDU supports this option, then the error Report shall specify the Complete Source Route option. The Source Route parameter value is obtained by extracting from the original Data PDU that portion of the complete source route that has already been traversed, and reversing the ISO 8473 [Page 26] RFC 994 December 1986 order of network-entity titles which comprise the list. If the system does not support the Complete Source Route Option, an Error Report must not be generated for a Data PDU that selects the Complete Source Route option. (d) The Padding, Partial Source Routing, and Record Route Options, if supported, may be specified in the Error Report PDU. Note: The values of the optional parameters in (d) above may be derived as a local matter, or they may be based upon the corresponding values in the original Data PDU. 6.11 PDU Header Error Detection The PDU Header Error Detection function protects against failure of intermediate or end-system network-entities due to the processing of erroneous information in the PDU header. The function is realized by a checksum computed on the entire PDU header. The checksum is veri- fied at each point at which the PDU header is processed. If the checksum calculation fails, the PDU must be discarded. If PDU header fields are modified (for example, due to operation of the lifetime function), then the checksum is modified so that the checksum remains valid. The use of the Header Error Detection function is optional, and is selected by the originating network-entity. If the function is not used, the checksum field of the PDU header is set to zero. If the function is selected by the originating network-entity, the value of the checksum field causes the following formulae to be sa- tisfied: (The Sum from i=1 to L of a(i)) (mod 255) = 0 (The Sum from i=1 to L of (L - i + 1) * a(i)) (mod 255) = 0 where L = the number of octets in the PDU header, and a(i) = the value of the octet at position i. The first octet in the PDU header is considered to occupy position i = 0. When the function is in use, neither octet of the checksum field may be set to zero. Note: 1. To ensure that inadvertent modification of a header while a PDU is being processed by an intermediate system (for example, due to a memory fault) may still be detected by the PDU Header Error function, an intermediate system network- ISO 8473 [Page 27] RFC 994 December 1986 entity must not recompute the checksum for the entire header, even if fields are modified. 2. Annex C contains descriptions of algorithms which may be used to calculate the correct value of the checksum field when the PDU is created, and to update the value of the checksum field when the header is modified. 6.12 Padding Function The padding function is provided to allow space to be reserved in the PDU header which is not used to support any other function. Octet alignment must be maintained. Note: An example of the use of this function is to cause the data field of a PDU to begin on a convenient boundary for the originating network-entity, such as a computer word boundary. 6.13 Security The provision of protection services (e.g., data origin authentica- tion, data confidentiality, and data integrity of a single connectionless-mode NSDU) is performed by the Security Function. The Security Function is related to the Protection from Unauthorized Access Quality of Service parameter described in ISO 8348/AD1, Adden- dum to the Network Service Definition Covering Connectionless-mode Transmission. The function is realized through selection of the secu- rity parameter in the options part of the PDU header. This Standard does not specify the way in which protection services are to be provided; it only provides for the encoding of security in- formation in the PDU header. To facilitate interoperation between end-systems and network relay-systems by avoiding different interpre- tations of the same encoding, a means to distinguish user-defined security encodings from standardized security encodings is described in Clause 7.5.3. Note: As an implementation consideration, data origin authentication may be provided through the use of a cryptographically generated or enciphered checksum (unique from the PDU Header Error Detection mechanism); data confidentiality and data integrity may be provided via route control mechanisms. 6.14 Source Routing Function The Source Routing function allows the originator to specify the path a generated PDU must take. Source routing may only be selected by the ISO 8473 [Page 28] RFC 994 December 1986 originator of a PDU. Source Routing is accomplished using a list of network-entity titles held in a parameter within the options part of the PDU header. The length of this parameter is determined by the originating network-entity, and does not change as the PDU traverses the network. The Source Route parameter includes information used by the originat- ing end-system when determining the initial route of the PDU. Only the titles of intermediate system network-entities are included in the list; the network-entity title of the destination of the PDU is not included in the list. Associated with the list of network-entity titles is an indicator which identifies the next entry in the list to be used; this indica- tor is advanced by the receiver of the PDU when the next title in the list matches its own. The indicator is updated as the PDU is forward- ed so as to identify the appropriate entry at each stage of relaying. Two forms of the Source Routing function are provided. The first form, referred to as Complete Source Routing, requires that the specified path must be taken; that is, only those systems identified in the list may be visited by the PDU while en route to the destina- tion, and each system must be visited in the order specified. If the specified path cannot be taken, the PDU must be discarded. Clause 6.10 describes the circumstances in which an attempt shall be made to inform the originator of the discard using the Error Reporting func- tion. The second form is referred to as Partial Source Routing. Again, each system identified in the list must be visited in the order specified while en route to the destination. However, with this form of source routing the PDU may take any path necessary to arrive at the next in- termediate system in the list, which may include visiting intermedi- ate systems that are not identified in the list. The PDU will not be discarded (for source routing related reasons) unless one of the sys- tems specified cannot be reached by any available route. 6.15 Record Route Function The Record Route function records the path(s) taken by a PDU as it traverses a series of intermediate systems. A recorded route consists of a list of network-entity titles held in a parameter within the op- tions part of the PDU header. The length of this parameter is deter- mined by the originating network-entity, and does not change as the PDU traverses the network. The list is constructed as the PDU is forwarded along a path towards its destination. Only the titles of intermediate system network- entities are included in the recorded route. The network-entity title of the originator of the PDU is not recorded in the list. ISO 8473 [Page 29] RFC 994 December 1986 When an intermediate system network-entity processes a PDU containing the Record Route parameter, the system adds its own networkentity ti- tle at the end of the list of recorded network-entity titles. An in- dicator is maintained to identify the next available octet to be used for recording of route. This indicator is updated as entries are ad- ded to the list as follows. The length of the entry to be added to the list is added to the value of the next available octet indicator, and this sum is compared with the length of the Record Route parame- ter. If the addition of the entry to the list would exceed the size of the parameter, the next available octet indicator is set to indi- cate that route recording has been terminated. The network-entity ti- tle is not added to the list. The PDU may still be forwarded to its final destination, without further addition of network-entity titles. If the addition of the entry would not exceed the size of the Record Route parameter, the next available octet indicator is updated with the new value, and the network-entity title is added to the head of the list after the other entries have been moved. Two forms of the Record Route function are provided. The first form is referred to as Complete Route Recording. It requires that the list of network-entity titles be a complete and accurate record of all intermediate systems visited by a PDU (including Derived PDUs), except when a shortage of space in the record route option field causes termination of recording of route, as described above. When Complete Route Recording is selected, PDU reassembly at intermediate systems is performed only when the Derived PDUs that are reassembled all took the same route; otherwise, the PDU is discarded, and if selected, an Error Report is generated (see Clause 6.10). The second form is referred to as Partial Route Recording. It also requires a record of intermediate systems visited by a PDU. When Par- tial Route Recording is selected, PDU reassembly at intermediate sys- tems is always permitted. When reassembly is performed at an inter- mediate system, the route recorded in any of the Derived PDUs may be placed in the PDU resulting from the reassembly. Note: The Record Route function is intended to be used in the diagnosis of subnetwork problems and/or to provide a return path that could be used as a source route in a subsequent PDU. 6.16 Quality of Service Maintenance Function The Quality of Service Maintenance function provides information to network-entities in intermediate systems which may be used to make routing decisions where such decisions affect the overall QoS provid- ed to NS users. This information is conveyed to intermediate system network- entities in a parameter in the options part of the PDU header. ISO 8473 [Page 30] RFC 994 December 1986 In those instances where the QoS requested cannot be maintained, in- termediate system network-entities shall attempt to deliver the PDU at a QoS different from the QoS requested. Intermediate system network-entities do not necessarily provide a notification of failure to meet the requested Quality of Service. 6.17 Priority Function The Priority function allows a PDU with a numerically higher priority value to be processed preferentially with respect to other PDUs with numerically lower priority values. The function is realized through selection of a parameter in the options part of the PDU header. The lowest priority value is zero; a source network-entity that does not support the Priority function must set the Priority value to zero. The Priority function provides a means whereby the resources of end and intermediate system network-entities, such as outgoing transmission queues and buffers, can be used preferentially to pro- cess higher-priority PDUs ahead of lower-priority PDUs. The specific action taken by an individual network-entity to support the Priority function is a local matter. 6.18 Congestion Notification Function To allow NS Users to take appropriate action when congestion is ex- perienced within the NS provider, intermediate systems may inform the destination network-entity of congestion through the use of a flag in the QoS Maintenance parameter in the options part of the PDU header. The value of this flag is initially set to zero (0) by the originator of the PDU and may be set to one (1) by any intermediate system which processes the PDU to indicate that it is experiencing congestion. The criteria for determining when this action is to be taken are a local matter. Note: Congestion typically corresponds to inavailability of buffer space to maintain output queues. An appropriate policy for indicating congestion may be based upon the depth of the output queue selected for a PDU (according to its destination address or other routing information). When the depth of a particular output queue exceeds a certain proportion of the depth of that queue, an intermediate system will start to discard PDUs. The intermediate system will set the Congestion Experienced flag in the next PDU to be forwarded and may continue to do so until the condition is alleviated. 6.19 Classification of Functions Implementations are not required to support all of the functions described in Clauses 6.1 through 6.18. Functions are divided into three categories: ISO 8473 [Page 31] RFC 994 December 1986 Type 1: These functions must be supported. Type 2: These functions may or may not be supported. If an implementation does not support a Type 2 function, and the function is selected in a PDU, then that PDU must be discarded, and an Error Report PDU must be generated and forwarded to the originating network-entity, providing that the Error Report flag is set and the conditions of Clause 6.10.4 are satisfied. Type 3: These functions may or may not be supported. If an implementation does not support a Type 3 function, and the function is selected in a PDU, then the function is not performed, and the PDU is processed exactly as though the function had not been selected. The protocol data unit shall not be discarded for this reason. Table 4 shows how the functions are divided into these three categories: _____________________________________________________________________________ | | FULL | NON | INACTIVE | | FUNCTION | PROTOCOL | SEGMENTING | SUBSET | | | | SUBSET | | |________________________________|_____________|_________________|____________| |PDU Composition | 1 | 1 | 1 | |PDU Composition | 1 | 1 | 1 | |Header Format Analysis | 1 | 1 | 1 | |PDU Lifetime Control | 1 | 1 | N/A | |Route PDU | 1 | 1 | N/A | |Forward PDU | 1 | 1 | N/A | |Segment PDU | 1 | N/A | N/A | |Reassemble PDU | 1 | N/A | N/A | |Discard PDU | 1 | 1 | N/A | |Error Reporting (Note 1) | 1 | 1 | N/A | |Header Error Detection (Note 1) | 1 | 1 | N/A | |Security | 1 | 2 | N/A | |Complete Source Routing | 1 | 2 | N/A | |Complete Route Recording | 2 | 2 | N/A | |Partial Source Routing | 3 | 3 | N/A | |Partial Route Recording | 3 | 3 | N/A | |Priority | 3 | 3 | N/A | |QoS Maintenance | 3 | 3 | N/A | |Congestion Notification | 3 | 3 | N/A | |Padding | 3 | 3 | N/A | |________________________________|_____________|_________________|____________| Table 4: Categorization of Protocol Functions ISO 8473 [Page 32] RFC 994 December 1986 Note: 1. While the Error Reporting and Header Error Detection functions must be provided, they are provided only when selected by the sending Network Service user. 2. The rationale for the inclusion of type 3 functions is that in the case of some functions it is more important to forward the PDUs between intermediate systems or deliver them to an end-system than it is to support the functions. Type 3 functions should be used in those cases where they are of an advisory nature; they cannot cause a PDU to be discarded when they are not supported. 7 Structure and Encoding of PDUs 7.1 Structure All Protocol Data Units shall contain an integral number of octets. The octets in a PDU are numbered starting from one (1) and increasing in the order in which they are submitted to the underlying service. The bits in an octet are numbered from one (1) to eight (8), where bit one (1) is the low-order (least significant) bit. When consecutive octets are used to represent a binary number, the lower octet number has the most significant value. Any implementation supporting this protocol is required to state in its specification the way in which octets are transferred, using the terms "most significant bit" and "least significant bit". The PDUs of this protocol are defined using the terms "most significant bit" and "least significant bit". Note: When the encoding of a PDU is represented using a diagram in this Clause the following representation is used: a) octets are shown with the lowest numbered octet to the left, higher number octets being further to the right; b) within an octet, bits are shown with bit eight (8) to the left and bit one (1) to the right. PDUs shall contain, in the following order: 1. the fixed part; 2. the address part; 3. the segmentation part, if present; 4. the Options part, if present; and the data field, if present. This structure is illustrated in Figure 2: ISO 8473 [Page 33] RFC 994 December 1986 7.2 Fixed Part 7.2.1 General The fixed part of the PDU header contains frequently occurring param- eters including the type code (DT or ER) of the protocol data unit. The length and the structure of the fixed part are defined by the PDU code. The fixed part has the following format: Part Described in ___________________________________ | Fixed Part | Section 7.2 |_________________________________| | Address Part | Section 7.3 |_________________________________| | Segmentation Part | Section 7.4 |_________________________________| | Options Part | Section 7.5 |_________________________________| | Data | Section 7.6 |_________________________________| Figure 2: PDU Structure Octet ________________________________________ | Network Layer Protocol Identifier | 1 |______________________________________| | Length Indicator | 2 |______________________________________| | Version/Protocol Id Extension | 3 |______________________________________| | Lifetime | 4 |______________________________________| | SP vline M S vline e/R | Type | 5 |______________________________________| | Segment Length | 6,7 |______________________________________| | Checksum | 8,9 |______________________________________| Figure 3: PDU Header -- Fixed Part 7.2.2 Network Layer Protocol Identifier The value of this field is set to binary 1000 0001 to identify this Network Layer protocol as ISO 8473, Protocol for Providing the Connectionless- mode Network Service. The value of this field is set ISO 8473 [Page 34] RFC 994 December 1986 to binary 0000 0000 to identify the Inactive Network Layer protocol subset. 7.2.3 Length Indicator The length is indicated by a binary number, with a maximum value of 254 (1111 1110). The length indicated is the length in octets of the header, as described in Clause 7.1. The value 255 (1111 1111) is reserved for possible future extensions. Note: The rules for forwarding and segmentation guarantee that the header length is the same for all segments (Derived PDUs) of the Initial PDU, and is the same as the header length of the Initial PDU. The size of a PDU header will not change due to operation of any protocol function. 7.2.4 Version/Protocol Identifier Extension The value of this field is binary 0000 0001, which identifies the standard Version 1 of ISO 8473, Protocol for Providing the Connectionless-mode Network Service. 7.2.5 PDU Lifetime The PDU Lifetime field is encoded as a binary number representing the remaining lifetime of the PDU, in units of 500 milliseconds. 7.2.6 Flags 7.2.6.1 Segmentation Permitted The Segmentation Permitted flag indicates whether segmentation is permitted. Its value is determined by the originator of the PDU and cannot be changed by any other network-entity for the lifetime of the Initial PDU and any Derived PDUs. A value of one (1) indicates that segmentation is permitted. A value of zero (0) indicates that the non-segmenting protocol subset is em- ployed. When the value of zero is selected, the segmentation part of the PDU header is not present, and the Segment Length field serves as the Total Length field (see Clause 7.2.8). 7.2.6.2 More Segments The More Segments flag indicates whether the data segment in this PDU contains (as its last octet) the last octet of the User Data in the NSDU. When the More Segments flag is set to one (1), segmentation has taken place and the last octet of the NSDU is not contained in this PDU. The More Segments flag cannot be set to one (1) if the Seg- mentation Permitted flag is not set to one (1). ISO 8473 [Page 35] RFC 994 December 1986 When the More Segments flag is set to zero (0), the last octet of the Data Part of the PDU is the last octet of the NSDU. 7.2.6.3 Error Report When the Error Report flag is set to one, the rules in Clause 6.10 are used to determine whether to generate an Error Report PDU if it is necessary to discard this Data PDU. When the Error Report flag is set to zero, discard of the Data PDU will not cause the generation of an Error Report PDU. 7.2.7 Type Code The Type code field identifies the type of the protocol data unit. Allowed values are given in Table 5: __________________________________________________ | | Bits 5 4 3 2 1 | |_________|______________________________________| | DT PDU | 1 1 1 0 0 | |_________|______________________________________| | ER PDU | 0 0 0 0 1 | |_________|______________________________________| Table 5: Valid PDU Types 7.2.8 PDU Segment Length The Segment Length field specifies the entire length, in octets, of the Derived PDU, including both header and data (if present). When the full protocol is employed and a PDU is not segmented, the value of this field is identical to the value of the Total Length field lo- cated in the Segmentation Part of the header. When the non-segmenting protocol subset is employed, no segmentation part is present in the header. In this subset, the Segment Length field specifies the entire length of the Initial PDU, including both header and data (if present). The Segment Length field is not changed for the lifetime of the PDU. 7.2.9 PDU Checksum The checksum is computed on the entire PDU header. For the Data PDU, this includes the segmentation and options parts (if present). For the Error Report PDU, this includes the reason for discard field as well. A checksum value of zero is reserved to indicate that the checksum is to be ignored. The operation of the PDU Header Error Detection func- tion (Clause 6.11) ensures that the value zero does not represent a ISO 8473 [Page 36] RFC 994 December 1986 valid checksum. A non-zero value indicates that the checksum must be processed. If the checksum calculation fails, the PDU must be dis- carded. 7.3 Address Part 7.3.1 General Address parameters are distinguished by their location, immediately following the fixed part of the PDU header. The address part is il- lustrated Figure 4: Octet ____________________________________________ | Destination Address Length Indicator | 10 |___________________________________________| | | 11 : Destination Address : | | m - 1 |___________________________________________| | Source Address Length Indicator | m |___________________________________________| | | m + 1 : Source Address : | | n - 1 |___________________________________________| Figure 4: PDU Header -- Address Part 7.3.1.1 Destination and Source Addresses The Destination and Source addresses used by this protocol are Net- work Service Access Point addresses as defined in ISO 8348/AD2, Ad- dendum to the Network Service Definition Covering Network Layer Ad- dressing. The Destination and Source Addresses are variable length. The Desti- nation and Source Address fields are encoded as Network Protocol Ad- dress Information using the Preferred Binary Encoding defined in Clause 8.3.1 of ISO 8348/AD2. The Destination Address Length Indicator field specifies the length of the Destination Address in octets. The Destination Address field follows the Destination Address Length Indicator field. The Source Address Length Indicator field specifies the length of the Source Address in octets. The Source Address Length Indicator field follows the Destination Address field. The Source Address field fol- lows the Source Address Length Indicator field. ISO 8473 [Page 37] RFC 994 December 1986 Each address parameter is encoded as illustrated in Table 5: ______________________________________________ | Octet | Address parameter Length Indicator | | n | (e.g., 'm') | |________|____________________________________| | Octets | | | n + 1 | Address Parameter Value | | thru | | | n + m | | |________|____________________________________| Figure 5: Address Parameters 7.4 Segmentation Part If the Segmentation Permitted Flag in the Fixed Part of the PDU Header (Octet 4, Bit 8) is set to one, the segmentation part of the header, illustrated in Figure 6, must be present: If the Segmentation Permitted flag is set to zero, the non-segmenting protocol subset is in use. Octet ________________________ | Data Unit Identifier | n, n + 1 |______________________| | Segment Offset | n + 2, n + 3 |______________________| | Total Length | n + 4, n + 5 |______________________| Figure 6: PDU Header -- Segmentation Part 7.4.1 Data Unit Identifier The Data Unit Identifier identifies an Initial PDU (and hence, its Derived PDUs) so that a segmented data unit may be correctly reassem- bled. The Data Unit Identifier size is two octets. 7.4.2 Segment Offset For each Derived PDU, the Segment Offset field specifies the relative position of the segment contained in the data field of the Derived PDU with respect to the start of the data field of the Initial PDU. The offset is measured in units of octets. The offset of the first segment (and hence, the Initial PDU) is zero; an unsegmented (Initial PDU) has a segment offset value of zero (0). The value of this field shall be a multiple of eight 8). ISO 8473 [Page 38] RFC 994 December 1986 7.4.3 PDU Total Length The Total Length field specifies the entire length of the Initial PDU, including both the header and data. This field is not changed for the lifetime of the Initial PDU (and hence, its Derived PDUs). 7.5 Options Part 7.5.1 General The options part is used to convey optional parameters. The options part of the PDU header is illustrated below: Octet ___________________________________________________ | | n + 6 : Options : | | p |__________________________________________________| Figure 7: PDU Header -- Options Part If the options part is present, it may contain one or more parame- ters. The number of parameters that may be contained in the options part is constrained by the length of the options part, which is determined by the following formula: PDU Header Length -(length of fixed part+length of address part+length of segmentation part) and by the length of the individual optional parameters. Parameters defined in the options part may appear in any order. Du- plication of options is not permitted. Receipt of a Protocol Data Unit with an option duplicated should be treated as a protocol error. The rules governing the treatment of protocol errors are described in Clause 6.10, Error Reporting Function. The encoding of parameters contained within the options part of the PDU header is illustrated in Table 6: Octets ___________________________________________ | n | Parameter Code | |____________|____________________________| | n + 1 | Parameter Length (e.g.m) | |____________|____________________________| | n + 2 | | | to | Parameter Value | | n + m + 1 | | |____________|____________________________| ISO 8473 [Page 39] RFC 994 December 1986 Table 6: Encoding of Parameters The parameter code field is coded in binary and, without extensions, provides a maximum of 255 different parameters. No parameter codes use bits 8 and 7 with the value 00, so the actual maximum number of parameters is lower. A parameter code of 255 (binary 1111 1111) is reserved for possible future extensions. The parameter length field indicates the length, in octets, of the parameter value field. The length is indicated by a positive binary number, m, with a theoretical maximum value of 254. The practical maximum value of m is lower. For example, in the case of a single parameter contained within the options part, two octets are required for the parameter code and the parameter length indicators. Thus, the value of m is limited to: m = 252-(length of fixed part +length of address part +length of seg- mentation part) For each succeeding parameter the maximum value of m decreases. The parameter value field contains the value of the parameter identified in the parameter code field. The following parameters are permitted in the options part. 7.5.2 Padding The padding parameter is used to lengthen the PDU header to a con- venient size (See Clause 6.12). Parameter Code: 1100 1100 Parameter Length: variable Parameter Value: any value is allowed 7.5.3 Security This parameter allows a unique and unambiguous security level to be assigned to a protocol data unit. Parameter Code: 1100 0101 Parameter Length: variable Parameter Value: The high order two bits of the first octet specify the Security Format Code, where: Security Type of Security Field: Format Code ISO 8473 [Page 40] RFC 994 December 1986 00 Reserved 01 Source Address Specific 10 Destination Address Specific 11 Globally Unique The rest of the first octet is reserved and must be zero. The remainder of the Parameter Value field specifies the security level as described in the following Clauses. 7.5.3.1 Source Address Specific The Security Format Code value of binary "01" indicates that the remaining octets of the parameter value field specify a security lev- el which is unique and unambiguous in the context of the security classification system employed by the authority responsible for as- signing the source NSAP Address. 7.5.3.2 Destination Address Specific The Security Format Code value of binary "10" indicates that the remaining octets of the parameter value field specify a security lev- el which is unique and unambiguous in the context of the security classification system employed by the authority responsible for as- signing the destination NSAP Address. 7.5.3.3 Globally Unique Security The Security Format Code value of binary "11" indicates that the remaining octets of the parameter value field specify a globally unique and unambiguous security level. This security classification system is not specified in this Standard. 7.5.4 Source Routing The source routing parameter specifies, either completely or partial- ly, the route to be taken from Source Network Address to Destination Network Address. Parameter Code: 1100 0101 Parameter Length: variable Parameter Value: 2 octets of control information succeeded by a concatenation of ordered network-entity title entries (ordered from source to destination) The first octet of the parameter value is the type code, and has the following significance: 0000 0000 partial source routing 0000 0001 complete source routing ISO 8473 [Page 41] RFC 994 December 1986 The second octet indicates the octet offset of the next network- entity title entry to be processed in the list. It is relative to the start of the parameter, such that a value of three (3) indicates that the next network-entity title entry begins immediately after this control octet. Successive octets are indicated by corresponding- ly larger values of this indicator. The third octet begins the network-entity title list. The list con- sists of variable length network-entity title entries. The first oc- tet of entry identifies the length of the network-entity title which comprises the re- mainder of the entry. 7.5.5 Recording of Route The recording of route parameter identifies the route of intermediate systems traversed by the PDU. Parameter Code: 1100 1011 Parameter Length: variable Parameter Value: 2 octets of control information succeeded by a con catenation of ordered network-entity title entries (ordered from destination to source) The first octet of the parameter value is the type code, and has the following significance: 0000 0000 Partial Recording of Route in progress 0000 0001 Complete Recording of Route in progress The second octet identifies the first octet not currently used for a recorded network-entity title, and therefore also the end of the list. It is encoded relative to the start of the parameter value, such that a value of three (3) indicates that no network-entity ti- tles have yet been recorded. A value of all ones is used to indicate that route recording has been terminated. The third octet begins the network-entity title list. The list con- sists of variable length network-entity title entries. The first oc- tet of each entry specifies the length of the network-entity title comprising the remainder of the entry. Network-entity title entries are always added to the beginning of the list; that is, the most re- cently added entry will begin in the third octet of the parameter value. Note: The length of the Record Route parameter is determined by the originator of the PDU and is not changed during the lifetime of the PDU; hence, the operation of the Record Route function does ISO 8473 [Page 42] RFC 994 December 1986 not affect the length of the header. 7.5.6 Quality of Service Maintenance The Quality of Service parameter conveys information about the quali- ty of service requested by the originating Network Service user. Network-entities in intermediate systems may (but are not required to) make use of this information as an aid in selecting a route when more than one route satisfying other routing criteria is available and the available routes are known to differ with respect to Quality of Service see Clause 6.16). Parameter Code: 1100 0011 Parameter Length: variable Parameter Value: The high order two bits of the first octet specify the QoS Format Code, where: QoS Format Type of QoS Code Field 00 Reserved 01 Source Address Specific 10 Destination Address Specific 11 Globally Unique The rest of the first octet is reserved and must be zero. The remainder of the Parameter Value field specifies the QoS as described in the following Clauses. 7.5.6.1 Source Address Specific The QoS Format Code value of binary "01" indicates that the remaining octets of the parameter value field specify a QoS which is unique and unambiguous in the context of the QoS Maintenance system employed by the authority responsible for assigning the source NSAP Address. 7.5.6.2 Destination Address Specific The QoS Format Code value of binary "10" indicates that the remaining octets of the parameter value field specify a QoS which is unique and unambiguous in the context of the QoS Maintenance system employed by the authority responsible for assigning the destination NSAP Address. 7.5.6.3 Globally Unique QoS The QoS Format Code value of binary "11" indicates that the remainder of the parameter value field specifies a globally unique QoS Mainte- nance field. When the globally unique QoS Maintenance function is em- ployed, the parameter value field must have a total length of one oc- tet, which is assigned the following values: Bits 8 and 7: QoS Format Code of binary "11" ISO 8473 [Page 43] RFC 994 December 1986 Bit 6: Reserved Bit 5: sequencing vs. transit delay Bit 4: congestion experienced Bit 3: transit delay vs. cost Bit 2: residual error probability vs. transit delay Bit 1: residual error probability vs. cost Bit 5 is set to one to indicate that, where possible, routing deci- sions should favor sending all PDUs to the specified destination NSAP address over a single path (in order to maintain sequence) over minimizing transit delay. A value of zero (0) indicates that, where possible, routing decisions should favor low transit delay over se- quence preservation. Bit 4 is set to zero by the network-entity which originates the pro- tocol data unit. It is set to one by an intermiediate system to indi- cate that this PDU has visited a congested intermediate system, and appropriate action should be taken by the destination network-entity. Once the congestion experienced bit is set by an intermediate system, it may not be reset by any intermediate system traversed by the PDU further along the path towards the destination. Bit 3 is set to one to indicate that, where possible, routing deci- sions should favor low transit delay over low cost. A value of 0 in- dicates that routing decisions should favor low cost over low transit delay. Bit 2 set to one to indicate that, where possible, routing decisions should favor low residual error probability over low transit delay. A value of zero indicates that routing decisions should favor low transit delay over low residual error probability. Bit 1 is set to one to indicate that, where possible, routing deci- sions should favor low residual error probability over low cost. A value of 0 indicates that routing decisions should favor low cost over low residual error probability. 7.5.7 Priority The value of the Priority parameter indicates the relative priority of the protocol data unit. Intermediate systems that support this option shall make use of this information in routing and in ordering PDUs for transmission. Parameter Code: 1100 1101 Parameter Length: one octet Parameter Value: 0000 0000 - Normal (Default) through 0000 1110 - Highest ISO 8473 [Page 44] RFC 994 December 1986 The values 0000 0001 through 0000 1110 are to be used for higher priority protocol data units. If an intermediate system does not sup- port this option, all PDUs shall be treated as if the field had the value 0000 0000. 7.6 Data Part The Data part of the PDU is structured as an ordered multiple of oc- tets, which is identical to the same ordered multiple of octets specified for the NS-Userdata parameter of the N-UNITDATA Request and Indication primitives. The data field is illustrated in Figure 8: Octet ___________________________________________________ | | p + 1 : Data : | | z |__________________________________________________| Figure 8: PDU Header -- Data Field ISO 8473 [Page 45] RFC 994 December 1986 7.7 Data (DT) PDU 7.7.1 Structure The DT PDU has the following format: __________________________________________ | Network Layer Protocol Identifier | 1 |________________________________________| | Length Indicator | 2 |________________________________________| | Version/Protocol Id Extension | 3 |________________________________________| | Lifetime | 4 |________________________________________| | S P vline M S vline e/R | Type | 5 |____________________________|___________| | Segment Length | 6,7 |________________________________________| | Checksum | 8,9 |________________________________________| | Destination Address Length Indicator | 10 |________________________________________| | | 11 : Destination Address : |________________________________________| m - 1 | Source Address Length Indicator | m |________________________________________| | | m + 1 : Source Address : | | n - 1 |________________________________________| | Data Unit Identifier | n, n + 1 |________________________________________| | Segment Offset | n + 2, n + 3 |________________________________________| | Total Length | n + 4, n + 5 |________________________________________| | | n + 6 | Options | | | p |________________________________________| | | p + 1 | Data | | | z |________________________________________| Figure 9: DT PDU ISO 8473 [Page 46] RFC 994 December 1986 7.7.1.1 Fixed Part 1) Network Layer Protocol Identifier See Clause 7.2.2 2) Length Indicator See Clause 7.2.3 3) Version/Protocol Id Extension See Clause 7.2.4 4) Lifetime See Clause 7.2.5 5) SP, MS, E/R See Clause 7.2.6 6) Type Code See Clause 7.2.7 7) Segment Length See Clause 7.2.8 8) Checksum See Clause 7.2.9 7.7.1.2 Addresses See Clause 7.3. 7.7.1.3 Segmentation See Clause 7.4. 7.7.1.4 Options See Clause 7.5. 7.7.1.5 Data See Clause 7.7. 7.8 Inactive Network Layer Protocol Octet ____________________________________ |Network Layer Protocol Identifier | 1 |__________________________________| | | 2 | Data | | | 2 - n |__________________________________| Figure 10: Inactive Network Layer Protocol 7.8.1 Network Layer Protocol Id The value of the Network Layer Protocol Identifier field is binary zero (0000 0000). 7.8.2 Data Field The length of the NS-Userdata parameter is constrained to be less than or equal to the value of the length of the SN-Userdata parameter minus one (see Clause 7.7). ISO 8473 [Page 47] RFC 994 December 1986 7.9 Error Report PDU (ER) 7.9.1 Structure The ER PDU has the following format: Octet ______________________________________________ | Network Layer Protocol Identifier | 1 |____________________________________________| | Length Indicator | 2 |____________________________________________| | Version/Protocol Id Extension | 3 |____________________________________________| | Lifetime | 4 |____________________________________________| | SP= 0 vline MS= 0 vline Reserved | Type | 5 |_____________________________________|______| | Segment Length | 6,7 |____________________________________________| | Checksum | 8,9 |____________________________________________| | Destination Address Length Indicator | 10 |____________________________________________| | | 11 : Destination Address : | | m - 1 |____________________________________________| | Source Address Length Indicator | m |____________________________________________| | | m + 1 : Source Address : | | n - 1 |____________________________________________| | | n | Options | | | p - 1 |____________________________________________| | | p | Reason for Discard | | | q - 1 |____________________________________________| | | q | Error Report Data Field | | | z |____________________________________________| Figure 11: Error Report PDU ISO 8473 [Page 48] RFC 994 December 1986 7.9.1.1 Fixed Part The fixed part of the Error Report Protocol Data Unit is composed in the same way as a new (Initial) Data PDU. References are provided to previous Clauses describing the encoding of the fields comprising the fixed part: 1) Network Layer Protocol Identifier See Clause 7.2.2 2) Length Indicator See Clause 7.2.3 3) Version/Protocol Id Extension See Clause 7.2.4 4) Lifetime See Clause 7.2.5 5) SP, MS, E/R Always set to zero, (See Clause 6.10) 6) Type Code See Clause 7.2.7 7) Segment Length See Clause 7.2.8 8) Checksum See Clause 7.2.9 7.9.1.2 Addresses See Clause 7.3. The Destination Address specifies the network-entity title of the origi- nator of the discarded PDU. The Source Address specifies the title of the intermediate-system or end-system network-entity initiating the Error Report PDU. 7.9.1.3 Options See Clause 7.5. ISO 8473 [Page 49] RFC 994 December 1986 7.9.1.4 Reason for Discard This parameter is valid only for the Error Report PDU. Parameter Code: 1100 0001 Parameter Length: two octets Parameter Value: type of error encoded in binary. Values are listed in Table 7: _______________________________________________________________________________ | Parameter Value | Class of | Meaning | | Octet 1 Octet 2| Error | | |__________________|_____________|_____________________________________________| | 0000 0000 | | Reason not specified | | 0001 | | Protocol Procedure Error | | 0010 | | Incorrect Checksum | | 0011 | General | PDU Discarded due to Congestion | | 0100 | | Header Syntax Error (cannot be parsed) | | 0101 | | Segmentation needed but not permitted | | 0110 | | Incomplete PDU Received | | 0111 | | Duplicate Option | |__________________|_____________|_____________________________________________| | 1000 0000 | Address | Destination Address Unreachable | | 0001 | | Destination Address Unknown | |__________________|_____________|_____________________________________________| | 1001 0000 | | Unspecified Source Routing Error | | 0001 | Source | Syntax Error in Source Routing Field | | 0010 | Routing | Unknown Address in Source Routing Field | | 0011 | | Path not Acceptable | |__________________|_____________|_____________________________________________| | 1010 0000 | Lifetime | Lifetime Expired while Data Unit in Transit | | 0001 | | Lifetime Expired during Reassembly | |__________________|_____________|_____________________________________________| | 1011 0000 | | Unsupported Option not Specified | | 0001 | PDU | Unsupported Protocol Version | | 0010 | Discarded | Unsupported Security Option | | 0011 | | Unsupported Source Routing Option | | 0100 | | Unsupported Recording of Route Option | |__________________|_____________|_____________________________________________| | 1100 0000 | Reassembly | Reassembly interference | |__________________|_____________|_____________________________________________| Table 7: Reasons for Discard The first octet of the parameter value contains an error type code. If the error in the discarded Data PDU can be localized to a particu- lar field, the number of the first octet of that field is stored in the second octet of the reason for discard parameter field. If the error cannot be localized to a particular field, or if the error is a checksum error, then the value zero is stored in the second octet of the reason for discard parameter field. ISO 8473 [Page 50] RFC 994 December 1986 7.9.1.5 Error Report Data Field This field contains the entire header of the discarded Data PDU, and may contain some or all of the data field of the discarded PDU. 8 Conformance For conformance to this International Standard, the ability to ori- ginate, manipulate, and receive PDUs in accordance with the full pro- tocol (as opposed to the non-segmenting or Inactive Network Layer Protocol subsets) is required. Additionally, conformance to the Standard requires provision of the protocol functions described in Clause 6. Provision of the optional functions described in Clause 6.18 and enumerated in Table 9-1 must meet the requirements described therein. Exceptions to this require- ment are described in Clause 8.1 below. Additionally, conformance to the Standard requires adherence to the structure and encoding of PDUs of Clause 7. If and only if the above requirements are met is there conformance to this International Standard. 8.1 Provision of Functions for Conformance The following table categorizes the functions in Clause 6 with respect to the type of system providing the function: Note: 1. The support of the PDU Composition and Forward PDU functions is necessary for the generation of Error Report PDUs. 2. The Segment PDU function is in general mandatory for an intermediate system. However, a system which is to be connected only to subnetworks all offering the same maximum SDU size (such as identical Local Area Networks) will not need to perform this function and therefore does not need to implement it. If this function is not implemented, this shall be stated as part of the specification of the implementation. 3. The correct treatment of the padding function requires no processing. A conforming implementation shall support the function, to the extent of ignoring this parameter wherever it may appear. 4. This function may or may not be supported. If an implementation does not support this function, and the ISO 8473 [Page 51] RFC 994 December 1986 function is selected in a PDU, then the PDU shall be discarded, and an ER PDU shall be generated and forwarded to the originating network-entity if the Error Report flag is set and the conditions of Clause 6.10.4 are satisfied. 5. This function may or may not be supported. If an implementation does not support this function, and the function is selected in a PDU, then the function is not performed and the PDU is processed exactly as though the function had not been selected. The PDU shall not be discarded for this reason. ___________________________________________________________________ | Function | Send | Forward | Receive | |____________________________|____________|___________|___________| | PDU Composition | M | (Note 1) | (Note 1) | | PDU Decomposition | M | - | M | | Header Format Analysis | - | M | M | | PDU Lifetime Control | | M | I | | Route PDU | - | M | - | | Forward PDU | M | M | (Note 1) | | Segment PDU | M | (Note 2) | - | | Reassemble PDU | - | I | M | | Discard PDU | - | M | M | | Error Reporting | M | M | M | | Header Error Detection | (Note 3) | M | M | | | | | | | Security | - | (Note 3) | (Note 4) | | Complete Source Routing | - | (Note 4) | - | | Complete Route Recording | - | (Note 4) | - | | Partial Source Routing | - | (Note 5) | - | | Partial Route Recording | - | (Note 5) | - | | Priority | - | (Note 5) | - | | QoS Maintenance | - | (Note 5) | - | | Congestion Notification | - | (Note 5) | - | | Padding | - | (Note 5) | (Note 3) | |____________________________|____________|___________|___________| Table 8: Categorization of Functions Key: M: Mandatory Function; this function must be implemented. -: Not applicable. I: Implementation option, as described in the text. NOTE: See notes above ISO 8473 [Page 52]