patch-2.3.12 linux/drivers/parport/ieee1284_ops.c

• Lines: 849
• Date: Tue Jul 6 19:08:33 1999
• Orig file: v2.3.11/linux/drivers/parport/ieee1284_ops.c
• Orig date: Wed Dec 31 16:00:00 1969

diff -u --recursive --new-file v2.3.11/linux/drivers/parport/ieee1284_ops.c linux/drivers/parport/ieee1284_ops.c
@@ -0,0 +1,848 @@
+/* IEEE-1284 operations for parport.
+ *
+ * This file is for generic IEEE 1284 operations.  The idea is that
+ * they are used by the low-level drivers.  If they have a special way
+ * of doing something, they can provide their own routines (and put
+ * the function pointers in port->ops); if not, they can just use these
+ * as a fallback.
+ *
+ * Note: Make no assumptions about hardware or architecture in this file!
+ *
+ * Author: Tim Waugh <tim@cyberelk.demon.co.uk>
+ */
+
+#include <linux/config.h>
+#include <linux/parport.h>
+#include <linux/delay.h>
+#include <asm/uaccess.h>
+
+#define DEBUG /* undef me for production */
+
+#ifdef CONFIG_LP_CONSOLE
+#undef DEBUG /* Don't want a garbled console */
+#endif
+
+#ifdef DEBUG
+#define DPRINTK(stuff...) printk (stuff)
+#else
+#define DPRINTK(stuff...)
+#endif
+
+/***                                *
+ * One-way data transfer functions. *
+ *                                ***/
+
+static inline
+int polling (struct pardevice *dev)
+{
+	return dev->port->irq == PARPORT_IRQ_NONE;
+}
+
+/* Compatibility mode. */
+size_t parport_ieee1284_write_compat (struct parport *port,
+				      const void *buffer, size_t len,
+				      int flags)
+{
+	ssize_t count = 0;
+	const unsigned char *addr = buffer;
+	unsigned char byte;
+	struct pardevice *dev = port->physport->cad;
+	unsigned char ctl = (PARPORT_CONTROL_SELECT
+			     | PARPORT_CONTROL_INIT);
+
+	if (port->irq != PARPORT_IRQ_NONE)
+		parport_enable_irq (port);
+
+	port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;
+	while (count < len) {
+		long expire = jiffies + dev->timeout;
+		long wait = (HZ + 99) / 100;
+		unsigned char mask = (PARPORT_STATUS_ERROR
+				      | PARPORT_STATUS_BUSY);
+		unsigned char val = (PARPORT_STATUS_ERROR
+				     | PARPORT_STATUS_BUSY);
+		int i;
+
+		/* Write the character to the data lines. */
+		byte = *addr++;
+		parport_write_data (port, byte);
+		udelay (1);
+
+		/* Wait until the peripheral's ready */
+		do {
+			/* Is the peripheral ready yet? */
+			if (!parport_wait_peripheral (port, mask, val))
+				/* Skip the loop */
+				goto ready;
+
+			/* Is the peripheral upset? */
+			if ((parport_read_status (port) &
+			     (PARPORT_STATUS_PAPEROUT |
+			      PARPORT_STATUS_SELECT |
+			      PARPORT_STATUS_ERROR))
+			    != (PARPORT_STATUS_SELECT |
+				PARPORT_STATUS_ERROR))
+				/* If nFault is asserted (i.e. no
+				 * error) and PAPEROUT and SELECT are
+				 * just red herrings, give the driver
+				 * a chance to check it's happy with
+				 * that before continuing. */
+				goto stop;
+
+			/* Have we run out of time? */
+			if (!time_before (jiffies, expire))
+				break;
+
+			/* Yield the port for a while.  If this is the
+                           first time around the loop, don't let go of
+                           the port.  This way, we find out if we have
+                           our interrupt handler called. */
+			if (count && polling (dev)) {
+				parport_release (dev);
+				current->state = TASK_INTERRUPTIBLE;
+				schedule_timeout (wait);
+				parport_claim_or_block (dev);
+			}
+			else
+				/* We must have the device claimed here */
+				parport_wait_event (port, wait);
+
+			/* Is there a signal pending? */
+			if (signal_pending (current))
+				goto stop;
+
+			/* Wait longer next time. */
+			wait *= 2;
+		} while (time_before (jiffies, expire));
+
+		DPRINTK (KERN_DEBUG "%s: Timed out\n", port->name);
+		break;
+
+	ready:
+		/* Clear out previous irqs. */
+		while (!down_trylock (&port->physport->ieee1284.irq));
+
+		/* Pulse strobe. */
+		parport_write_control (port, ctl | PARPORT_CONTROL_STROBE);
+		udelay (1); /* strobe */
+
+		parport_write_control (port, ctl);
+		udelay (1); /* hold */
+
+		/* Wait until it's received (up to 20us). */
+		for (i = 0; i < 20; i++) {
+			if (!down_trylock (&port->physport->ieee1284.irq) ||
+			    !(parport_read_status (port) & PARPORT_STATUS_ACK))
+				break;
+			udelay (1);
+		}
+
+		count++;
+
+                /* Let another process run if it needs to. */
+		if (time_before (jiffies, expire))
+			if (!parport_yield_blocking (dev)
+			    && current->need_resched)
+				schedule ();
+	}
+ stop:
+	port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
+
+	return count;
+}
+
+/* Nibble mode. */
+size_t parport_ieee1284_read_nibble (struct parport *port, 
+				     void *buffer, size_t len,
+				     int flags)
+{
+#ifndef CONFIG_PARPORT_1284
+	return 0;
+#else
+	unsigned char *buf = buffer;
+	int i;
+	unsigned char byte = 0;
+
+	len *= 2; /* in nibbles */
+	for (i=0; i < len; i++) {
+		unsigned char nibble;
+
+		/* Does the error line indicate end of data? */
+		if (((i & 1) == 0) &&
+		    (parport_read_status(port) & PARPORT_STATUS_ERROR)) {
+			port->physport->ieee1284.phase = IEEE1284_PH_HBUSY_DNA;
+			DPRINTK (KERN_DEBUG
+				"%s: No more nibble data (%d bytes)\n",
+				port->name, i/2);
+
+			/* Go to reverse idle phase. */
+			parport_frob_control (port,
+					      PARPORT_CONTROL_AUTOFD,
+					      PARPORT_CONTROL_AUTOFD);
+			port->physport->ieee1284.phase = IEEE1284_PH_REV_IDLE;
+			break;
+		}
+
+		/* Event 7: Set nAutoFd low. */
+		parport_frob_control (port,
+				      PARPORT_CONTROL_AUTOFD,
+				      PARPORT_CONTROL_AUTOFD);
+
+		/* Event 9: nAck goes low. */
+		port->ieee1284.phase = IEEE1284_PH_REV_DATA;
+		if (parport_wait_peripheral (port,
+					     PARPORT_STATUS_ACK, 0)) {
+			/* Timeout -- no more data? */
+			DPRINTK (KERN_DEBUG
+				 "%s: Nibble timeout at event 9 (%d bytes)\n",
+				 port->name, i/2);
+			break;
+		}
+
+
+		/* Read a nibble. */
+		nibble = parport_read_status (port) >> 3;
+		nibble &= ~8;
+		if ((nibble & 0x10) == 0)
+			nibble |= 8;
+		nibble &= 0xf;
+
+		/* Event 10: Set nAutoFd high. */
+		parport_frob_control (port, PARPORT_CONTROL_AUTOFD, 0);
+
+		/* Event 11: nAck goes high. */
+		if (parport_wait_peripheral (port,
+					     PARPORT_STATUS_ACK,
+					     PARPORT_STATUS_ACK)) {
+			/* Timeout -- no more data? */
+			DPRINTK (KERN_DEBUG
+				 "%s: Nibble timeout at event 11\n",
+				 port->name);
+			break;
+		}
+
+		if (i & 1) {
+			/* Second nibble */
+			byte |= nibble << 4;
+			*buf++ = byte;
+		} else 
+			byte = nibble;
+	}
+
+	i /= 2; /* i is now in bytes */
+
+	if (i == len) {
+		/* Read the last nibble without checking data avail. */
+		port = port->physport;
+		if (parport_read_status (port) & PARPORT_STATUS_ERROR)
+			port->ieee1284.phase = IEEE1284_PH_HBUSY_DNA;
+		else
+			port->ieee1284.phase = IEEE1284_PH_HBUSY_DAVAIL;
+	}
+
+	return i;
+#endif /* IEEE1284 support */
+}
+
+/* Byte mode. */
+size_t parport_ieee1284_read_byte (struct parport *port,
+				   void *buffer, size_t len,
+				   int flags)
+{
+#ifndef CONFIG_PARPORT_1284
+	return 0;
+#else
+	unsigned char *buf = buffer;
+	ssize_t count = 0;
+
+	for (count = 0; count < len; count++) {
+		unsigned char byte;
+
+		/* Data available? */
+		if (parport_read_status (port) & PARPORT_STATUS_ERROR) {
+			port->physport->ieee1284.phase = IEEE1284_PH_HBUSY_DNA;
+			DPRINTK (KERN_DEBUG
+				 "%s: No more byte data (%d bytes)\n",
+				 port->name, count);
+
+			/* Go to reverse idle phase. */
+			parport_frob_control (port,
+					      PARPORT_CONTROL_AUTOFD,
+					      PARPORT_CONTROL_AUTOFD);
+			port->physport->ieee1284.phase = IEEE1284_PH_REV_IDLE;
+			break;
+		}
+
+		/* Event 7: Set nAutoFd low. */
+		parport_frob_control (port,
+				      PARPORT_CONTROL_AUTOFD,
+				      PARPORT_CONTROL_AUTOFD);
+
+		/* Event 9: nAck goes low. */
+		port->physport->ieee1284.phase = IEEE1284_PH_REV_DATA;
+		if (parport_wait_peripheral (port,
+					     PARPORT_STATUS_ACK,
+					     0)) {
+			/* Timeout -- no more data? */
+			parport_frob_control (port, PARPORT_CONTROL_AUTOFD,
+						 0);
+			DPRINTK (KERN_DEBUG "%s: Byte timeout at event 9\n",
+				 port->name);
+			break;
+		}
+
+		byte = parport_read_data (port);
+		*buf++ = byte;
+
+		/* Event 10: Set nAutoFd high */
+		parport_frob_control (port, PARPORT_CONTROL_AUTOFD, 0);
+
+		/* Event 11: nAck goes high. */
+		if (parport_wait_peripheral (port,
+					     PARPORT_STATUS_ACK,
+					     PARPORT_STATUS_ACK)) {
+			/* Timeout -- no more data? */
+			DPRINTK (KERN_DEBUG "%s: Byte timeout at event 11\n",
+				 port->name);
+			break;
+		}
+
+		/* Event 16: Set nStrobe low. */
+		parport_frob_control (port,
+				      PARPORT_CONTROL_STROBE,
+				      PARPORT_CONTROL_STROBE);
+		udelay (5);
+
+		/* Event 17: Set nStrobe high. */
+		parport_frob_control (port, PARPORT_CONTROL_STROBE, 0);
+	}
+
+	if (count == len) {
+		/* Read the last byte without checking data avail. */
+		port = port->physport;
+		if (parport_read_status (port) & PARPORT_STATUS_ERROR)
+			port->ieee1284.phase = IEEE1284_PH_HBUSY_DNA;
+		else
+			port->ieee1284.phase = IEEE1284_PH_HBUSY_DAVAIL;
+	}
+
+	return count;
+#endif /* IEEE1284 support */
+}
+
+/***              *
+ * ECP Functions. *
+ *              ***/
+
+#ifdef CONFIG_PARPORT_1284
+
+static inline
+int ecp_forward_to_reverse (struct parport *port)
+{
+	int retval;
+
+	/* Event 38: Set nAutoFd low */
+	parport_frob_control (port,
+			      PARPORT_CONTROL_AUTOFD,
+			      PARPORT_CONTROL_AUTOFD);
+	parport_data_reverse (port);
+	udelay (5);
+
+	/* Event 39: Set nInit low to initiate bus reversal */
+	parport_frob_control (port,
+			      PARPORT_CONTROL_INIT,
+			      PARPORT_CONTROL_INIT);
+
+	/* Event 40: PError goes low */
+	retval = parport_wait_peripheral (port,
+					  PARPORT_STATUS_PAPEROUT, 0);
+
+	if (!retval) {
+		DPRINTK (KERN_DEBUG "%s: ECP direction: reverse\n",
+			 port->name);
+		port->ieee1284.phase = IEEE1284_PH_REV_IDLE;
+	}
+
+	return retval;
+}
+
+static inline
+int ecp_reverse_to_forward (struct parport *port)
+{
+	int retval;
+
+	/* Event 47: Set nInit high */
+	parport_frob_control (port,
+			      PARPORT_CONTROL_INIT,
+			      PARPORT_CONTROL_INIT);
+	parport_data_reverse (port);
+
+	/* Event 49: PError goes high */
+	retval = parport_wait_peripheral (port,
+					  PARPORT_STATUS_PAPEROUT,
+					  PARPORT_STATUS_PAPEROUT);
+
+	if (!retval) {
+		parport_data_forward (port);
+		DPRINTK (KERN_DEBUG "%s: ECP direction: forward\n",
+			 port->name);
+		port->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
+	}
+
+	return retval;
+}
+
+#endif /* IEEE1284 support */
+
+/* ECP mode, forward channel, data. */
+size_t parport_ieee1284_ecp_write_data (struct parport *port,
+					const void *buffer, size_t len,
+					int flags)
+{
+#ifndef CONFIG_PARPORT_1284
+	return 0;
+#else
+	const unsigned char *buf = buffer;
+	size_t written;
+	int ctl = parport_read_control (port) & ~PARPORT_CONTROL_AUTOFD;
+	int retry;
+
+	port = port->physport;
+
+	if (port->ieee1284.phase != IEEE1284_PH_FWD_IDLE)
+		if (ecp_reverse_to_forward (port))
+			return 0;
+
+	port->ieee1284.phase = IEEE1284_PH_FWD_DATA;
+
+	/* HostAck high (data, not command) */
+	parport_write_control (port, ctl);
+	for (written = 0; written < len; written++, buf++) {
+		long expire = jiffies + port->cad->timeout;
+		unsigned char byte;
+
+		byte = *buf;
+	try_again:
+		parport_write_data (port, byte);
+		parport_write_control (port, ctl | PARPORT_CONTROL_STROBE);
+		udelay (5);
+		for (retry = 0; retry < 100; retry++) {
+			if (!parport_wait_peripheral (port,
+						      PARPORT_STATUS_BUSY, 0))
+				goto success;
+
+			if (signal_pending (current)) {
+				parport_write_control (port, ctl);
+				break;
+			}
+		}
+
+		/* Time for Host Transfer Recovery (page 41 of IEEE1284) */
+		DPRINTK (KERN_DEBUG "%s: ECP transfer stalled!\n", port->name);
+
+		parport_write_control (port, ctl | PARPORT_CONTROL_INIT);
+		udelay (50);
+		if (parport_read_status (port) & PARPORT_STATUS_PAPEROUT) {
+			/* It's buggered. */
+			parport_write_control (port, ctl);
+			break;
+		}
+
+		parport_write_control (port, ctl);
+		udelay (50);
+		if (!(parport_read_status (port) & PARPORT_STATUS_PAPEROUT))
+			break;
+
+		DPRINTK (KERN_DEBUG "%s: Host transfer recovered\n",
+			 port->name);
+
+		if (time_after_eq (jiffies, expire)) break;
+		goto try_again;
+	success:
+		parport_write_control (port, ctl);
+		udelay (5);
+		if (parport_wait_peripheral (port,
+					     PARPORT_STATUS_BUSY,
+					     PARPORT_STATUS_BUSY))
+			/* Peripheral hasn't accepted the data. */
+			break;
+	}
+
+	port->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
+
+	return written;
+#endif /* IEEE1284 support */
+}
+
+/* ECP mode, reverse channel, data. */
+size_t parport_ieee1284_ecp_read_data (struct parport *port,
+				       void *buffer, size_t len, int flags)
+{
+#ifndef CONFIG_PARPORT_1284
+	return 0;
+#else
+	struct pardevice *dev = port->cad;
+	unsigned char *buf = buffer;
+	int rle_count = 0; /* shut gcc up */
+	int rle = 0;
+	ssize_t count = 0;
+
+	port = port->physport;
+
+	if (port->ieee1284.phase != IEEE1284_PH_REV_IDLE)
+		if (ecp_forward_to_reverse (port))
+			return 0;
+
+	port->ieee1284.phase = IEEE1284_PH_REV_DATA;
+
+	/* Set HostAck low to start accepting data. */
+	parport_frob_control (port, PARPORT_CONTROL_AUTOFD,
+			      PARPORT_CONTROL_AUTOFD);
+	while (count < len) {
+		long expire = jiffies + dev->timeout;
+		unsigned char byte;
+		int command;
+
+		/* Event 43: Peripheral sets nAck low. It can take as
+                   long as it wants. */
+		while (parport_wait_peripheral (port,
+						PARPORT_STATUS_ACK,
+						PARPORT_STATUS_ACK)) {
+			/* The peripheral hasn't given us data in
+			   35ms.  If we have data to give back to the
+			   caller, do it now. */
+			if (count)
+				goto out;
+
+			/* If we've used up all the time we were allowed,
+			   give up altogether. */
+			if (!time_before (jiffies, expire))
+				goto out;
+
+			/* Yield the port for a while. */
+			if (count && polling (dev)) {
+				parport_release (dev);
+				current->state = TASK_INTERRUPTIBLE;
+				schedule_timeout ((HZ + 99) / 25);
+				parport_claim_or_block (dev);
+			}
+			else
+				/* We must have the device claimed here. */
+				parport_wait_event (port, (HZ + 99) / 25);
+
+			/* Is there a signal pending? */
+			if (signal_pending (current))
+				goto out;
+		}
+
+		/* Is this a command? */
+		if (rle)
+			/* The last byte was a run-length count, so
+                           this can't be as well. */
+			command = 0;
+		else
+			command = (parport_read_status (port) &
+				   PARPORT_STATUS_BUSY) ? 1 : 0;
+
+		/* Read the data. */
+		byte = parport_read_data (port);
+
+		/* If this is a channel command, rather than an RLE
+                   command or a normal data byte, don't accept it. */
+		if (command) {
+			if (byte & 0x80) {
+				DPRINTK (KERN_DEBUG "%s: stopping short at "
+					 "channel command (%02x)\n",
+					 port->name, byte);
+				goto out;
+			}
+			else if (port->ieee1284.mode != IEEE1284_MODE_ECPRLE)
+				DPRINTK (KERN_DEBUG "%s: device illegally "
+					 "using RLE; accepting anyway\n",
+					 port->name);
+
+			rle_count = byte + 1;
+
+			/* Are we allowed to read that many bytes? */
+			if (rle_count > (len - count)) {
+				DPRINTK (KERN_DEBUG "%s: leaving %d RLE bytes "
+					 "for next time\n", port->name,
+					 rle_count);
+				break;
+			}
+
+			rle = 1;
+		}
+
+		/* Event 44: Set HostAck high, acknowledging handshake. */
+		parport_frob_control (port, PARPORT_CONTROL_AUTOFD, 0);
+
+		/* Event 45: The peripheral has 35ms to set nAck high. */
+		if (parport_wait_peripheral (port, PARPORT_STATUS_ACK, 0)) {
+			/* It's gone wrong.  Return what data we have
+                           to the caller. */
+			DPRINTK (KERN_DEBUG "ECP read timed out at 45\n");
+
+			if (command)
+				printk (KERN_WARNING
+					"%s: command ignored (%02x)\n",
+					port->name, byte);
+
+			break;
+		}
+
+		/* Event 46: Set HostAck low and accept the data. */
+		parport_frob_control (port,
+				      PARPORT_CONTROL_AUTOFD,
+				      PARPORT_CONTROL_AUTOFD);
+
+		/* If we just read a run-length count, fetch the data. */
+		if (command)
+			continue;
+
+		/* If this is the byte after a run-length count, decompress. */
+		if (rle) {
+			rle = 0;
+			memset (buf, byte, rle_count);
+			buf += rle_count;
+			count += rle_count;
+			DPRINTK (KERN_DEBUG "%s: decompressed to %d bytes\n",
+				 port->name, rle_count);
+		}
+		else
+			/* Normal data byte. */
+			*buf++ = byte, count++;
+	}
+
+ out:
+	return count;
+#endif /* IEEE1284 support */
+}
+
+/* ECP mode, forward channel, commands. */
+size_t parport_ieee1284_ecp_write_addr (struct parport *port,
+					const void *buffer, size_t len,
+					int flags)
+{
+#ifndef CONFIG_PARPORT_1284
+	return 0;
+#else
+	const unsigned char *buf = buffer;
+	size_t written;
+	int ctl = parport_read_control (port) | PARPORT_CONTROL_AUTOFD;
+	int retry;
+
+	port = port->physport;
+
+	if (port->ieee1284.phase != IEEE1284_PH_FWD_IDLE)
+		if (ecp_reverse_to_forward (port))
+			return 0;
+
+	port->ieee1284.phase = IEEE1284_PH_FWD_DATA;
+
+	/* HostAck low (command, not data) */
+	parport_write_control (port, ctl);
+	for (written = 0; written < len; written++, buf++) {
+		long expire = jiffies + port->cad->timeout;
+		unsigned char byte;
+
+		byte = *buf;
+	try_again:
+		parport_write_data (port, byte);
+		parport_write_control (port, ctl | PARPORT_CONTROL_STROBE);
+		udelay (5);
+		for (retry = 0; retry < 100; retry++) {
+			if (!parport_wait_peripheral (port,
+						      PARPORT_STATUS_BUSY, 0))
+				goto success;
+
+			if (signal_pending (current)) {
+				parport_write_control (port, ctl);
+				break;
+			}
+		}
+
+		/* Time for Host Transfer Recovery (page 41 of IEEE1284) */
+		DPRINTK (KERN_DEBUG "%s: ECP transfer stalled!\n", port->name);
+
+		parport_write_control (port, ctl | PARPORT_CONTROL_INIT);
+		udelay (50);
+		if (parport_read_status (port) & PARPORT_STATUS_PAPEROUT) {
+			/* It's buggered. */
+			parport_write_control (port, ctl);
+			break;
+		}
+
+		parport_write_control (port, ctl);
+		udelay (50);
+		if (!(parport_read_status (port) & PARPORT_STATUS_PAPEROUT))
+			break;
+
+		DPRINTK (KERN_DEBUG "%s: Host transfer recovered\n",
+			 port->name);
+
+		if (time_after_eq (jiffies, expire)) break;
+		goto try_again;
+	success:
+		parport_write_control (port, ctl);
+		udelay (5);
+		if (parport_wait_peripheral (port,
+					     PARPORT_STATUS_BUSY,
+					     PARPORT_STATUS_BUSY))
+			/* Peripheral hasn't accepted the data. */
+			break;
+	}
+
+	port->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
+
+	return written;
+#endif /* IEEE1284 support */
+}
+
+/***              *
+ * EPP functions. *
+ *              ***/
+
+/* EPP mode, forward channel, data. */
+size_t parport_ieee1284_epp_write_data (struct parport *port,
+					const void *buffer, size_t len,
+					int flags)
+{
+	/* This is untested */
+	unsigned char *bp = (unsigned char *) buffer;
+	size_t ret = 0;
+
+	parport_frob_control (port,
+			      PARPORT_CONTROL_STROBE |
+			      PARPORT_CONTROL_AUTOFD |
+			      PARPORT_CONTROL_SELECT,
+			      PARPORT_CONTROL_STROBE |
+			      PARPORT_CONTROL_SELECT);
+	port->ops->data_forward (port);
+	for (; len > 0; len--, bp++) {
+		parport_write_data (port, *bp);
+
+		if (parport_wait_peripheral (port, PARPORT_STATUS_BUSY,
+					     PARPORT_STATUS_BUSY))
+			break;
+
+		/* Strobe data */
+		parport_frob_control (port, PARPORT_CONTROL_AUTOFD,
+				      PARPORT_CONTROL_AUTOFD);
+
+		if (parport_wait_peripheral (port, PARPORT_STATUS_BUSY, 0))
+			break;
+
+		parport_frob_control (port, PARPORT_CONTROL_AUTOFD, 0);
+		ret++;
+	}
+
+	return ret;
+}
+
+/* EPP mode, reverse channel, data. */
+size_t parport_ieee1284_epp_read_data (struct parport *port,
+				       void *buffer, size_t len,
+				       int flags)
+{
+	/* This is untested. */
+	unsigned char *bp = (unsigned char *) buffer;
+	unsigned ret = 0;
+
+	parport_frob_control (port,
+			      PARPORT_CONTROL_STROBE |
+			      PARPORT_CONTROL_AUTOFD |
+			      PARPORT_CONTROL_SELECT, 0);
+	port->ops->data_reverse (port);
+	for (; len > 0; len--, bp++) {
+		if (parport_wait_peripheral (port, PARPORT_STATUS_BUSY,
+					     PARPORT_STATUS_BUSY))
+			break;
+
+		parport_frob_control (port, PARPORT_CONTROL_AUTOFD,
+				      PARPORT_CONTROL_AUTOFD);
+
+		if (parport_wait_peripheral (port, PARPORT_STATUS_BUSY, 0))
+			break;
+
+		*bp = parport_read_data (port);
+
+		parport_frob_control (port, PARPORT_CONTROL_AUTOFD, 0);
+		ret++;
+	}
+	port->ops->data_forward (port);
+
+	return ret;
+}
+
+/* EPP mode, forward channel, addresses. */
+size_t parport_ieee1284_epp_write_addr (struct parport *port,
+					const void *buffer, size_t len,
+					int flags)
+{
+	/* This is untested */
+	unsigned char *bp = (unsigned char *) buffer;
+	size_t ret = 0;
+
+	parport_frob_control (port,
+			      PARPORT_CONTROL_STROBE |
+			      PARPORT_CONTROL_SELECT |
+			      PARPORT_CONTROL_AUTOFD,
+			      PARPORT_CONTROL_STROBE |
+			      PARPORT_CONTROL_SELECT);
+	port->ops->data_forward (port);
+	for (; len > 0; len--, bp++) {
+		parport_write_data (port, *bp);
+
+		if (parport_wait_peripheral (port, PARPORT_STATUS_BUSY,
+					     PARPORT_STATUS_BUSY))
+			break;
+
+		/* Strobe data */
+		parport_frob_control (port, PARPORT_CONTROL_SELECT,
+				      PARPORT_CONTROL_SELECT);
+
+		if (parport_wait_peripheral (port, PARPORT_STATUS_BUSY, 0))
+			break;
+
+		parport_frob_control (port, PARPORT_CONTROL_SELECT, 0);
+		ret++;
+	}
+
+	return ret;
+}
+
+/* EPP mode, reverse channel, addresses. */
+size_t parport_ieee1284_epp_read_addr (struct parport *port,
+				       void *buffer, size_t len,
+				       int flags)
+{
+	/* This is untested. */
+	unsigned char *bp = (unsigned char *) buffer;
+	unsigned ret = 0;
+
+	parport_frob_control (port,
+			      PARPORT_CONTROL_STROBE |
+			      PARPORT_CONTROL_SELECT |
+			      PARPORT_CONTROL_AUTOFD, 0);
+	port->ops->data_reverse (port);
+	for (; len > 0; len--, bp++) {
+		if (parport_wait_peripheral (port, PARPORT_STATUS_BUSY,
+					     PARPORT_STATUS_BUSY))
+			break;
+
+		parport_frob_control (port, PARPORT_CONTROL_SELECT,
+				      PARPORT_CONTROL_SELECT);
+
+		if (parport_wait_peripheral (port, PARPORT_STATUS_BUSY, 0))
+			break;
+
+		*bp = parport_read_data (port);
+
+		parport_frob_control (port, PARPORT_CONTROL_SELECT, 0);
+		ret++;
+	}
+	port->ops->data_forward (port);
+
+	return ret;
+}