| Internet-Draft | Network Time Protocol Version 5 | June 2024 |
| Lichvar | Expires 21 December 2024 | [Page] |
This document describes the version 5 of the Network Time Protocol (NTP).¶
This Internet-Draft is submitted in full conformance with the provisions of BCP 78 and BCP 79.¶
Internet-Drafts are working documents of the Internet Engineering Task Force (IETF). Note that other groups may also distribute working documents as Internet-Drafts. The list of current Internet-Drafts is at https://datatracker.ietf.org/drafts/current/.¶
Internet-Drafts are draft documents valid for a maximum of six months and may be updated, replaced, or obsoleted by other documents at any time. It is inappropriate to use Internet-Drafts as reference material or to cite them other than as "work in progress."¶
This Internet-Draft will expire on 21 December 2024.¶
Copyright (c) 2024 IETF Trust and the persons identified as the document authors. All rights reserved.¶
This document is subject to BCP 78 and the IETF Trust's Legal Provisions Relating to IETF Documents (https://trustee.ietf.org/license-info) in effect on the date of publication of this document. Please review these documents carefully, as they describe your rights and restrictions with respect to this document. Code Components extracted from this document must include Revised BSD License text as described in Section 4.e of the Trust Legal Provisions and are provided without warranty as described in the Revised BSD License.¶
Network Time Protocol (NTP) is a protocol which enables computers to synchronize their clocks over network. Time is distributed from primary time servers to clients, which can be servers for other clients, and so on. Clients can use multiple servers simultaneously.¶
NTPv5 is similar to NTPv4 [RFC5905]. The main differences are:¶
The protocol specification (this document) describes only the on-wire protocol. Filtering of measurements, security mechanisms, source selection, clock control, and other algorithms, are out of scope.¶
For security reasons, NTPv5 drops support for the symmetric active, symmetric passive, broadcast, control, and private modes. The symmetric and broadcast modes are vulnerable to replay attacks. The control and private modes can be exploited for denial-of-service traffic amplification attacks. Only the client and server modes remain in NTPv5.¶
Timestamps are clearly separated from values used as cookies.¶
NTPv5 messages can be extended only with extension fields. The MAC field is wrapped in an extension field.¶
Extension fields can be of any length, even indivisible by 4, but are padded to a multiple of 4 octets. Extension fields specified for NTPv4 are compatible with NTPv5.¶
NTPv5 adds support for other timescales than UTC.¶
The NTP era number is exchanged in the protocol, which extends the unambiguous interval of the client from 136 years to about 35000 years.¶
NTPv5 adds interleaved mode to provide clients with more accurate transmit timestamps.¶
NTPv5 works with sets of reference IDs to prevent synchronization loops over multiple hosts.¶
Resolution of the root delay and root dispersion fields is improved from about 15 microseconds to about 4 nanoseconds.¶
Clients do not leak information about their clock (e.g. timestamps).¶
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "NOT RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in BCP 14 [RFC2119] [RFC8174] when, and only when, they appear in all capitals, as shown here.¶
The distance to the reference time sources in the hierarchy of servers is called stratum. Primary time servers, which are synchronized to the reference clocks, are stratum 1, their clients are stratum 2, and so on.¶
Root delay measures the total delay on the path to the reference time source used by the primary time server. Each client on the path adds to the root delay the NTP delay measured to the server it considers best for synchronization. The delay includes network delays and any delays between timestamping of NTP messages and their actual reception and transmission. Half of the root delay estimates the maximum error of the clock due to asymmetries in the delay.¶
Root dispersion estimates the maximum error of the clock due to the instability of the clocks on the path and instability of NTP measurements. Each server on the path adds its own dispersion to the root dispersion. Different clock models can be used. In a simple model, the clock can have a constant dispersion rate, e.g. 15 ppm as used in NTPv4.¶
The sum of the root dispersion and half of the root delay is called root distance. It is the estimated maximum error of the clock, taking into account asymmetry in delay and stability of clocks and measurements.¶
Servers have randomly generated reference IDs to enable detection and prevention of synchronization loops.¶
NTPv5 uses few different data types. They are all in the network order. Beside signed and unsigned integers, it has also the following fixed-point types:¶
Some fields use a logarithmic scale, where an 8-bit signed integer represents the rounded log2 value of seconds. For example, a log2 value of 4 is 2^4 (2 to the power of 4, 16) seconds, or a log2 value of -2 is 2^-2 (0.25 seconds).¶
NTPv5 servers and clients exchange messages as UDP datagrams. Clients send requests to servers and servers send them back responses. The format of the UDP payload is shown in Figure 1.¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |LI | VN |Mode | Stratum | Poll | Precision | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Timescale | Era | Flags | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Root Delay | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Root Dispersion | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + Server Cookie (64) + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + Client Cookie (64) + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + Receive Timestamp (64) + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + Transmit Timestamp (64) + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . . . Extension Field 1 (variable) . . . | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ . . . . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . . . Extension Field N (variable) . . . | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Each NTPv5 message has a header containing the following fields:¶
An 8-bit identifier of the timescale. In requests it is the requested timescale. In responses it is the timescale of the receive and transmit timestamps. Defined values are:¶
A 16-bit integer that can contain the following flags:¶
The header has 48 octets, which is the minimum length of a valid NTPv5 message. A message can contain optional extension fields (zero or more). The maximum length is not specified, but the length MUST be divisible by 4.¶
The format of NTPv5 extension fields is shown in Figure 2.¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ . . . Data (variable) . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Each extension field has a header which contains a 16-bit type and 16-bit length. The length is in octets and it includes the header. The minimum length is 4, i.e. an extension field does not have to contain any data. If the length is not divisible by 4, the extension field is padded with zeros to the smallest multiple of 4 octets.¶
If a request contains an extension field, the server MUST include this extension field in the response unless the specification of the extension field states otherwise, or the server does not support the extension field. A client can interpret the absence of an expected extension field in a response as an indication that the server does not support the extension field.¶
Extension fields specified for NTPv4 can be included in NTPv5 messages as specified for NTPv4.¶
The rest of this section describes extension fields specified for NTPv5. Clients are not required to use or support any of these extension fields, but servers are required to support at least the Padding Extension Field, Server Information Extension field, and if they can be synchronized to other servers, also the Reference IDs Request and Response extension fields to enable detection of synchronization loops.¶
Note to the editors: this section must be removed before final publication.¶
This field, with type 0xF5FF, is used to indicate which draft of the specification an implementation is based upon. It MUST be included in NTPv5 requests produced by an implementation based on a draft of this specification, and MUST NOT be included in NTPv5 requests produced by an implementation based on the final version of this specification. Server MUST use this field if and only if responding to a request containing this field and the server is a draft implementation.¶
The contents of this field MUST be the full name, including version number, of the draft upon which the implementation is based, encoded as an ASCII string. If the server string is longer than the client string, the server MUST truncate it to the length of the client string.¶
A server SHOULD NOT respond to requests with a draft identification it does not recognize, and SHOULD respond with a response according to the same draft specification as given by the client.¶
Note: the content of this field MUST NOT be null terminated¶
This field, with type [[TBD]] (draft: 0xF501), is used by servers to pad the response to the same length as the request if the response does not contain all requested extension fields, or some have a variable length. It can have any length. The data field of the extension field SHOULD contain zeros and it MUST be ignored by the receiver.¶
This field MUST be supported on servers.¶
This field, with type [[TBD]] (draft: 0xF502), authenticates the NTPv5 message with a symmetric key. Implementations SHOULD use the MAC specified in RFC8573 [RFC8573]. The extension field MUST be the last extension field in the message unless an extension field is specifically allowed to be placed after a MAC or another authenticator field.¶
Each NTPv5 server has a randomly generated 120-bit reference ID (it will be split into 10 12-bit values). The extension fields described in this section are used to exchange sets of reference IDs in order to detect synchronization loops, i.e. when a client is synchronizing (directly or indirectly) to one of its own clients.¶
As each client can be synchronized to an unlimited number of servers (and there can be up to 15 strata of servers), the reference IDs are exchanged as a Bloom filter [Bloom] instead of a list to limit the amount of data that needs to be exchanged.¶
The Bloom filter is an array of 4096 bits. When empty, all bits are zero. To add a reference ID to the filter, the 120-bit value of the reference ID is split into 10 12-bit values and the bits of the array at the 10 positions given by the 12-bit values are set to one.¶
A server maintains a copy of the filter for each server it is using as an NTP client. The filter provided by the server to clients is the union of the filters (using the bitwise OR operation) of the server's sources selected for synchronization and the server's own reference ID.¶
If the server uses a previous version of NTP for some of its sources, the reference IDs added to the filter are generated from their IP addresses as the first 120 bits of the MD5 [RFC1321] sum of the address.¶
A client checking whether the server's set of reference IDs contains the client's own reference ID checks whether the bits at the 10 positions corresponding to the 12-bit values from the reference ID are all set to one.¶
When a client which serves time to other clients detects a synchronization loop with one of its servers, it SHOULD stop using the server for synchronization. When the client's reference ID is no longer detected in the server's filter, it SHOULD wait for a random number of polling intervals (e.g. between 0 and 4) before selecting the server again. The random delay helps with stabilization of the selection in longer loops.¶
False positives are possible. The probability of a collision grows with the number of reference IDs in the filter. With 26 reference IDs it is about 1e-12. With 118 IDs it is about 1e-6. The client MAY avoid selecting a server which has too many bits set in the filter (e.g. more than half) to reduce the probability of the collision for its own clients. A client which detected a synchronization loop MAY change its own reference ID to limit the duration of the potential collision.¶
The filter can be exchanged as a single 512-octet array, or it can be exchanged in smaller chunks over multiple NTP messages, making them shorter, but delaying the detection of the synchronization loop.¶
The request extension field specifies the offset of the requested chunk in the filter as a number of octets. The requested length of the chunk is given by the length of the extension field. The response extension field MUST have the same length as the request extension field. If the request contains an invalid offset, the extension field MUST be ignored.¶
The client SHOULD use requests of a constant length for the association to avoid adding a variation to the measured NTP delay.¶
The format of the Reference IDs Request is shown in Figure 3.¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = [[TBD]] (draft 0xF503) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Offset | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ + . . . Padding (variable) . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The format of the Reference IDs Response is shown in Figure 4.¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = [[TBD]] (draft 0xF504) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ . . . Bloom filter chunk (variable) . . . +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
These fields MUST be supported on servers which can be synchronized to other NTP servers (i.e. they can be in a synchronization loop).¶
This field provides clients with information about which NTP versions are supported by the server, i.e. whether it can respond to requests conforming to the specific version. It contains a 16-bit field with flags indicating support for NTP versions in the range of 1 to 16, where the least significant bit corresponds to the version 1. The extension field has a fixed length of 8 octets. In requests, all data fields of the extension are 0.¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = [[TBD]] (draft 0xF505) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Supported NTP versions | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
This field MUST be supported on servers.¶
Processing and queueing delays in network switches and routers may be a significant source of jitter and asymmetry in network delay, which has a negative impact on accuracy and stability of clocks synchronized by NTP. A solution to this problem is defined in the Precision Time Protocol (PTP) [IEEE1588], which is a different protocol for synchronization of clocks in networks. In PTP a special type of switch or router, called a Transparent Clock (TC), updates a correction field in PTP messages to account for the time messages spend in the TC. This is accomplished by timestamping the message at the ingress and egress ports, taking the difference to determine time in the TC and adding this to the Delay Correction. Clients can account for the accumulated Delay Correction to determine a more accurate clock offset and network delay.¶
The NTPv5 Delay Correction has the same format as the PTP correctionField to make it easier for manufacturers of switches and routers to implement NTP corrections. The format of the Correction Extension Field is shown in Figure 6.¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = [[TBD]] (draft 0xF506) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + Origin Correction + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Origin Path ID | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | + Delay Correction + | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Delay Path ID | Checksum Complement | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
An NTP client with enabled support for network corrections SHOULD add the Correction Extension Field to its requests, with all fields of the extension field set to zero. It MUST be the last extension field in the NTP message.¶
A network device forwarding packets (e.g. a switch or router) with enabled support for NTP corrections MUST modify only packets which meet all of the following requirements:¶
It is an IPv4 or IPv6 packet (e.g. EtherType of 0x0800 or 0x86DD)¶
The IP protocol number is 17 (UDP)¶
The UDP source port or destination port is 123 (NTP)¶
The NTP version is 5¶
The NTP message contains the Correction Extension Field¶
The network device SHOULD add the difference between the beginning of the NTP message retransmission and the end of the message reception to the Delay Correction value in the Correction Extension Field. Note that this time difference might be negative, e.g. in a cut-through switch. If the packet is transmitted at the same speed as it was received and the length of the packet does not change (e.g. due to adding or removing a VLAN tag), the beginning and end of the interval may correspond to any point of the reception and transmission as long as it is consistent for all forwarded packets of the same length. If the transmission speed or length of the packet is different, the beginning and end of the interval SHOULD correspond to the end of the reception and beginning of the transmission respectively.¶
The receive timestamp of the ingress port and transmit timestamp of the egress port MUST be from the same clock, or two clocks that are synchronized to each other. The clocks do not need to be synchronized to an external reference if their frequency is accurate enough for the accuracy of measured NTP delay required by the application. The correction field is updated before or during the transmission of the message. It is a one-step end-to-end transparent clock in the PTP terminology.¶
The network device SHOULD have a randomly generated 16-bit ID number assigned to each of its ports. When it modifies the Correction Extension Field, it SHOULD update the Path ID field of the extension field by adding to it the values of the incoming and outgoing port ID. The Path ID values can be used by clients to determine if the NTP request and response have likely traversed the same network path.¶
If the network device modified any fields of the Correction Extension Field, it MUST also update the Checksum Complement field in order to keep the existing UDP checksum valid, or update the UDP checksum in the UDP header itself. The network device MUST NOT modify any other data in the UDP payload.¶
If an NTP server supports the Correction Extension Field and receives a request which contains this extension field, it SHOULD include the extension field in the response. If it is included, it MUST be the last extension field in the message. It MUST copy the Delay Correction and Path ID from the request to the Origin Correction and Origin Path ID fields in the response respectively. It SHOULD set the Delay Correction and Path ID fields of the response to zero.¶
The Correction Extension Field is required to be the last extension field in the message to provide an indicator at a fixed offset from the ending of the message reception (which might simplify hardware implementation of the correction) and to avoid being covered by the MAC Extension Field, or other authenticator extension fields (e.g. Network Time Security). It is the exception in the requirement specified for the MAC Extension Field. If the corrections were covered by the authenticator fields, the network devices would need to have access to the keys and have a significant additional complexity in order to update the authenticator fields when they modify the Correction Extension Field.¶
As the Correction Extension Field is not protected, NTP clients MUST validate the corrections before their application as specified in Measurement Modes (Section 6). Clients MUST ignore an unexpected Correction Extension Field in the response, i.e. if it was not included in the request.¶
This field contains the time of the last update of the clock. It has a fixed length of 12 octets. In requests, that timestamp is always 0.¶
(Is this really needed? It was mostly unused in NTPv4.)¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = [[TBD]] (draft 0xF507) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Reference Timestamp (64) | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
When a clock is synchronized to a time source, there is a compromise between time (phase) accuracy and frequency accuracy, because the frequency of the clock has to be adjusted to correct time errors that accumulate due to the frequency error (e.g. caused by changes in the temperature of the crystal). Faster corrections of time can minimize the time error, but increase the frequency error, which transfers to clients using that clock as a time source and increases their frequency and time errors. This issue can be avoided by transferring time and frequency separately using different clocks.¶
The Monotonic Receive Timestamp Extension Field contains an extra receive timestamp with a 32-bit epoch ID captured by a clock which does not have corrected phase and can better transfer frequency than the clock which captures the receive and transmit timestamps in the header. The extension field has a constant length of 16 octets. In requests, the counter and timestamp are always 0.¶
The epoch ID is a random number which is changed when frequency transfer needs to be restarted, e.g. due to a step of the clock.¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = [[TBD]] (draft 0xF508) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Epoch ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Monotonic Receive Timestamp (64) | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The client can determine the frequency-transfer offset from the time-transfer offset and difference between the two receive timestamps in the response. It can use the frequency-transfer offset to better control the frequency of its clock, avoiding the frequency error in the server's time-transfer clock.¶
This extension field provides an additional receive timestamp of the client request in a selected timescale. It enables the client to get the same receive timestamp in different timescales in order to calculate the current offset between the timescales.¶
In requests, the Timescale field selects the requested timescale. The other data fields in the extension field MUST be set to 0.¶
The Timescale, Era, and Secondary Receive Timestamp fields in a response have the same meaning as the Timescale, Era, and Receive Timestamp fields in the header respectively.¶
If the server does not support the requested timescale, it MUST ignore the extension field in the request. If the server supports the timescale, but does not have a reliable timestamp (e.g. due to being close to a leap second), it SHOULD set the timestamp field to 0.¶
The server MAY provide in this extension field timestamps in timescales which it does not provide in the header, e.g. it can provide UTC in addition to leap-smeared UTC to enable its clients to measure the current smearing offset.¶
A request MAY contain multiple instances of this extension field, but each timescale MUST be requested at most once, not counting the timescale in the header. The server SHOULD include in its response timestamps in all timescales it supports.¶
0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type = [[TBD]] (draft 0xF509) | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Timescale | Era | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | | Secondary Receive Timestamp (64) | | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
An NTPv5 client needs four timestamps to measure the offset and delay of its clock relative to the server's clock:¶
T1 - client's transmit timestamp of a request¶
T2 - server's receive timestamp of the request¶
T3 - server's transmit timestamp of a response¶
T4 - client's receive timestamp of the response¶
The offset, delay and dispersion are calculated as:¶
where¶
T1, T2, T3, T4 are the receive and transmit timestamps of a request and response¶
DR is the client's dispersion rate¶
If the Correction Extension Field is used and the corrections are known for both the request and response, a corrected offset and delay is calculated:¶
where¶
Co is the Origin Correction from the response to the request corresponding to timestamps T1 and T2¶
Cd is the Delay Correction from the response corresponding to timestamps T3 and T4¶
FC is the maximum expected frequency error of devices providing the delay corrections (e.g. 100 ppm)¶
Drx is the time it took to receive the frame containing the response corresponding to T3 and T4¶
Dtx is the time it took to transmit the frame containing the request corresponding to T1 and T2. If unknown, it SHOULD be set to Drx.¶
The corrected offset and delay MUST NOT be accepted if any of delay_c, Co and Cr is negative. The uncorrected delay MUST always be used for calculation of root delay.¶
The client can make measurements in the basic mode, or interleaved mode if supported on the server. In the basic mode, the transmit timestamp in the server response corresponds to the message which contains the timestamp itself. In the interleaved mode it corresponds to a previous response identified by the server cookie. The interleaved mode enables the server to provide the client with a more accurate transmit timestamp which is available only after the response was formed or sent.¶
An example of cookies and timestamps in an NTPv5 exchange using the basic mode is shown in Figure 10.¶
Server t2 t3 t6 t7 t10 t11
-----+----+----------------+----+----------------+----+-----
/ \ / \ / \
Client / \ / \ / \
--+----------+----------+----------+----------+----------+--
t1 t4 t5 t8 t9 t12
+----+ +----+ +----+ +----+ +----+ +----+
SC | 0 | | s1 | | 0 | | s2 | | 0 | | s3 |
CC | c1 | | c1 | | c2 | | c2 | | c3 | | c3 |
Rx | 0 | | t2 | | 0 | | t6 | | 0 | |t10 |
Tx | 0 | | t3 | | 0 | | t7 | | 0 | |t11 |
+----+ +----+ +----+ +----+ +----+ +----+
From the three exchanges in this example, the client would use the the following sets of timestamps:¶
For NTPv4, the interleaved mode is described in NTP Interleaved Modes [I-D.ietf-ntp-interleaved-modes]. The difference between the NTPv5 and NTPv4 interleaved modes is that in NTPv5 it is enabled with a flag and the previous transmit timestamp on the server is identified by the server cookie instead of the receive timestamp.¶
An example of an NTPv5 exchange using the interleaved mode is shown in Figure 11. The messages in the basic and interleaved mode are indicated with B and I respectively. The timestamps t3' and t11' correspond to the same transmissions as t3 and t11, but they may be less accurate (e.g. due to being captured in software before the transmission). The first exchange is in the basic mode followed by a second exchange in the interleaved mode. For the third exchange, the client request is in the interleaved mode, but the server response is in the basic mode, because the server no longer had the timestamp t7 (e.g. it was dropped to save timestamps for other clients using the interleaved mode).¶
Server t2 t3 t6 t7 t10 t11
-----+----+----------------+----+----------------+----+-----
/ \ / \ / \
Client / \ / \ / \
--+----------+----------+----------+----------+----------+--
t1 t4 t5 t8 t9 t12
Mode: B B I I I B
+----+ +----+ +----+ +----+ +----+ +----+
SC | 0 | | s1 | | s1 | | s2 | | s2 | | s3 |
CC | c1 | | c1 | | c2 | | c2 | | c3 | | c3 |
Rx | 0 | | t2 | | 0 | | t6 | | 0 | |t10 |
Tx | 0 | | t3'| | 0 | | t3 | | 0 | |t11'|
+----+ +----+ +----+ +----+ +----+ +----+
From the three exchanges in this example, the client would use the following sets of timestamps:¶
An NTPv5 client can use one or multiple servers. It has a separate association with each server. It makes periodic measurements of its offset and delay to the server. It can filter the measurements and compare measurements from different servers to select and combine the best servers for synchronization. It can adjust its clock in order to minimize its offset and keep the clock synchronized. These algorithms are not specified in this document.¶
The polling interval can be adjusted for the network conditions and stability of the clock. When polling a public server on Internet, the client SHOULD use a polling interval of at least 64 seconds, increasing in normal conditions up to at least 1024 seconds to avoid excessive load on the server in case the implementation is used on a very large number of systems.¶
Each successful measurement provides the client with an offset, delay and dispersion. When combined with the server's root delay and dispersion, it gives the client an estimate of the maximum error.¶
On each poll, the client:¶
Generates a new random cookie.¶
Formats a request with necessary extension fields and the fields in the header all zero except:¶
Version is set to 5.¶
Mode is set to 3.¶
Scale is set to the timescale in which the client wants to operate.¶
Poll is set to the rounded log2 value of the current client's polling interval in seconds.¶
Flags are set according to the requested mode. The interleaved mode flag requests the server to save the transmit timestamp of the response and provide the transmit timestamp of a previous response corresponding to the server cookie (if not zero).¶
Server cookie is set only in the interleaved mode. It is set to the server cookie from the last valid response, or zero if no such response was received yet or the transmit timestamp of that response would no longer be useful to the client (e.g. after missing too many responses).¶
Client cookie is set to the newly generated cookie.¶
Sends the request to the server to the UDP port 123 and captures a transmit timestamp for the packet.¶
Waits for a valid response from the server and captures a receive timestamp. A valid response has version 5, mode 4, client cookie equal to the cookie from the request, and passes authentication if enabled. The client MUST ignore all invalid responses and accept at most one valid response.¶
Checks whether the response is usable for synchronization of the clock. Such a response has a leap indicator not equal to 3, stratum between 0 and 16, root delay and dispersion both smaller than a specific value, e.g. 16 seconds, and timescale equal to the requested timescale. If the response is in a different timescale, the client can switch to the provided timescale, convert the timestamps if the offset between the timescales is known from the Secondary Receive Timestamp Extension Field or other sources, or ignore the response.¶
Saves the server's receive and transmit timestamps. If the client internally counts seconds using a type wider than 32 bits, it SHOULD expand the timestamps with the provided NTP era.¶
Calculates the offset, delay, and dispersion as specified in Measurement Modes (Section 6).¶
A client which operates as a server for other clients MUST include the Reference IDs Request Extension Field in its requests in order to track reference IDs of its sources. If the server's set of reference IDs contains the client's own reference ID, it SHOULD not select the server for synchronization to avoid a synchronization loop. If the client is requesting the reference IDs in multiple chunks, it SHOULD NOT select the server for synchronization until it received the whole set.¶
A client which uses multiple servers MUST be able to handle servers providing timestamps in different timescales. It can ignore servers not using the most common or preferred timescale, or convert them to a common timescale if it knows the offsets between them.¶
If the client synchronizes its clock to a leap-smeared timescale, it MUST NOT apply leap seconds and it SHOULD provide the same timescale to its own clients if it is a server.¶
The client SHOULD periodically (e.g. every two weeks) refresh IP addresses of all servers specified by hostname to limit the amount of traffic that migrated or decommissioned servers will receive from long-running clients.¶
A server receives requests on the UDP port 123. The server MUST support measurements in the basic mode. It MAY support the interleaved mode.¶
For the basic mode the server does not need to keep any client-specific state. For the interleaved mode it needs to save transmit timestamps and be able to identify them by a cookie.¶
The server maintains its leap indicator, stratum, root delay, and root dispersion:¶
Leap indicator MUST be 3 if the clock is not synchronized or its maximum error cannot be estimated with the root delay and dispersion. Otherwise, it MUST be 0, 1, 2, depending on whether a leap second is pending in the next 14 days and, if it is, whether it will be inserted or deleted.¶
Stratum SHOULD be one larger than stratum of the best server it uses for its own synchronization.¶
Root delay SHOULD be the best server's root delay in addition to the measured delay to the server.¶
Root dispersion SHOULD be the best server's root dispersion in addition to an estimate of the maximum drift of its own clock since the last update of the clock.¶
The server has a randomly generated 120-bit reference ID. It MUST track reference IDs of its servers in order to be able to respond with a Reference IDs Response Extension Field.¶
For each received request, the server:¶
Captures a receive timestamp.¶
Checks the version in the request. If it is not equal to 5, it MUST either drop the request, or handle it according to the specification corresponding to the protocol version.¶
Drops the request if the format is not valid, mode is not 3, or authentication fails with the MAC Extension Field or another authenticator which does not have a specified response for failed authentication. The server MUST ignore unknown extension fields.¶
Server forms a response with requested extension fields and sets the fields in the header as follows:¶
Leap Indicator, Stratum, Root delay, and Root dispersion, are set to the current server's values.¶
Version is set to 5.¶
Scale is set to the client's requested timescale if it is supported by the server. If not, the server SHOULD respond in any timescale it supports.¶
The flags are set as follows:¶
Era is set to the NTP era of the receive timestamp.¶
Server Cookie is set when the interleaved mode is requested and it is supported by the server, even if the response cannot be in the requested mode due to the request having an unknown or zero server cookie. The cookie identifies a more accurate transmit timestamp of the response, which can be retrieved by the client later with another request. The cookie generation is implementation-specific.¶
Client Cookie is set to the Client Cookie from the request.¶
Receive Timestamp is set to the server's receive timestamp of the request.¶
Transmit Timestamp is set to a value which depends on the measurement mode. In the basic mode it is the server's current time when the message is formed. In the interleaved mode it is the transmit timestamp of the previous response identified by the server cookie in the request, captured at some point after the message was formed.¶
Adds the Padding Extension field if necessary to make the length of the response equal to the length of the request.¶
Drops the response if it is longer than the request to prevent traffic amplification.¶
Sends the response.¶
Saves the transmit timestamp and server cookie, if the interleaved mode was requested and is supported by the server.¶
The Network Time Security [RFC8915] mechanism uses the NTS-KE protocol to establish keys and negotiate the next protocol. NTPv5 can be indicated as the next protocol with identifier [[TBD]] (draft use 0x8001). This can be used by clients and servers to negotiate NTPv5 for an NTS session.¶
No new NTS-KE records are specified for NTPv5. The records that were specified for NTPv4 (i.e. NTPv4 New Cookie, NTPv4 Server Negotiation, and NTPv4 Port Negotiation) are reused for NTPv5.¶
The NTS extension fields specified for NTPv4 are compatible with NTPv5. No new extension fields are specified.¶
(Note to editor: remove this paragraph before publishing.) Client implementations of a draft of this specification MUST provide the identity of the draft implemented as data in an NTS-KE record of type 0x4001, which does not have the critical bit set. The draft identity MUST be encoded as ascii and MUST not contain any trailing 0 bytes. Servers that implement a draft MUST not accept NTPv5 as an option unless they support the specific draft version identified.¶
NTPv5 messages are not compatible with NTPv4 and other previous versions of NTP, even if they do not contain any extension fields. Some widely used server NTPv4 implementations are known to accept requests indicating a higher version, interpreting them as NTPv4, and copying the version number from the request to its NTPv4 response. Responses to NTPv5 requests have a zero client cookie, which causes them to fail the NTPv5 validation and be ignored by the client.¶
The implementations are also known to not respond to requests with an unknown extension field, which prevents an NTPv4 extension field to be specified for NTPv5 negotiation. Instead, the negotiation reuses the reference timestamp field.¶
An NTP server which supports NTPv5 and also NTPv4, NTPv3, NTPv2, or NTPv1, SHOULD check the reference timestamp in received client-mode requests of the previous NTP versions. If the reference timestamp contains the value 0x4E5450354E545035 ("NTP5NTP5" in ASCII), it SHOULD respond with the same reference timestamp to indicate it supports NTPv5.¶
Note to the editor: Remove this paragraph before publication. Implementations of a draft of this specification SHOULD use 0x4E54503544524654 ("NTP5DRFT" in ASCII) instead of 0x4E5450354E545035.¶
When NTPv5 is not expected to be widely supported on servers yet, an NTP client which supports both NTPv5 and a previous NTP version, is not configured to use a specific NTP version, and does not use NTS or other mechanism including negotiation of the NTP version, SHOULD start with the previous version and set the reference timestamp to 0x4e5450354e545035. If the server responds with the same reference timestamp, the client SHOULD switch to NTPv5. If no valid response is received for a number of requests (e.g. 2), the client SHOULD switch back to the orignal NTP version and stick with it for a larger number of requests (e.g. 256) before trying NTPv5 again.¶
The special value of the reference timestamp corresponds to 1941-08-24T01:13:25Z in NTP era 0 and 2077-09-29T07:41:41Z in NTP era 1. The negotiation will probably not be needed at that time anymore. If NTPv5 servers and NTPv4-or-older-only clients are still in use and they send a request with the special value by chance, they will get an acceptable response with no side effects. If an NTPv5 client gets the special value by chance from an NTPv4-or-older-only server, it will switch to NTPv5 and back after missing a valid response.¶
Some ideas were taken from a different NTPv5 design proposed by Daniel Franke.¶
The author would like to thank Doug Arnold and David Venhoek for their contributions and Dan Drown, Watson Ladd, Hal Murray, Kurt Roeckx, and Ulrich Windl for their suggestions and comments.¶
IANA is requested to create a new registry for NTPv5 Extension Field Types with initial entries including all entries from the NTPv4 Extension Field Types Registry [RFC5905] and the following NTPv5-specific entries:¶
| Field Type | Meaning | Reference |
|---|---|---|
| [[TBD]], selected by IANA from the IETF Review range | Padding | [[this memo]] |
| [[TBD]], selected by IANA from the IETF Review range | MAC | [[this memo]] |
| [[TBD]], selected by IANA from the IETF Review range | Reference IDs Request | [[this memo]] |
| [[TBD]], selected by IANA from the IETF Review range | Reference IDs Response | [[this memo]] |
| [[TBD]], selected by IANA from the IETF Review range | Server Information | [[this memo]] |
| [[TBD]], selected by IANA from the IETF Review range | Correction | [[this memo]] |
| [[TBD]], selected by IANA from the IETF Review range | Reference Timestamp | [[this memo]] |
| [[TBD]], selected by IANA from the IETF Review range | Monotonic Receive Timestamp | [[this memo]] |
| [[TBD]], selected by IANA from the IETF Review range | Secondary Receive Timestamp | [[this memo]] |
IANA is requested to allocate the following protocol in the Network Time Security Next Protocols Registry [RFC8915]:¶
| Protocol ID | Protocol Name | Reference |
|---|---|---|
| [[TBD]], selected by IANA from the IETF Review range | Network Time Protocol version 5 (NTPv5) | [[this memo]] |
The corrections provided by network devices in the Correction Extension Field are not authenticated. Man-in-the-middle attackers can modify the corrections, but only corrections smaller than the measured delay are accepted by clients. The security impact is comparable to the impact of delaying unmodified NTP messages, which generally cannot be prevented.¶