Network Working Group R. Coltun Request for Comments: 5340 Acoustra Productions Obsoletes: 2740 D. Ferguson Category: Standards Track Juniper Networks J. Moy Sycamore Networks, Inc A. Lindem, Ed. Redback Networks July 2008 OSPF for IPv6 Status of This Memo This document specifies an Internet standards track protocol for the Internet community, and requests discussion and suggestions for improvements. Please refer to the current edition of the "Internet Official Protocol Standards" (STD 1) for the standardization state and status of this protocol. Distribution of this memo is unlimited. Abstract This document describes the modifications to OSPF to support version 6 of the Internet Protocol (IPv6). The fundamental mechanisms of OSPF (flooding, Designated Router (DR) election, area support, Short Path First (SPF) calculations, etc.) remain unchanged. However, some changes have been necessary, either due to changes in protocol semantics between IPv4 and IPv6, or simply to handle the increased address size of IPv6. These modifications will necessitate incrementing the protocol version from version 2 to version 3. OSPF for IPv6 is also referred to as OSPF version 3 (OSPFv3). Changes between OSPF for IPv4, OSPF Version 2, and OSPF for IPv6 as described herein include the following. Addressing semantics have been removed from OSPF packets and the basic Link State Advertisements (LSAs). New LSAs have been created to carry IPv6 addresses and prefixes. OSPF now runs on a per-link basis rather than on a per-IP-subnet basis. Flooding scope for LSAs has been generalized. Authentication has been removed from the OSPF protocol and instead relies on IPv6's Authentication Header and Encapsulating Security Payload (ESP). Even with larger IPv6 addresses, most packets in OSPF for IPv6 are almost as compact as those in OSPF for IPv4. Most fields and packet- size limitations present in OSPF for IPv4 have been relaxed. In addition, option handling has been made more flexible. Coltun, et al. Standards Track [Page 1]
RFC 5340 OSPF for IPv6 July 2008 All of OSPF for IPv4's optional capabilities, including demand circuit support and Not-So-Stubby Areas (NSSAs), are also supported in OSPF for IPv6. Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1. Requirements Notation . . . . . . . . . . . . . . . . . . 4 1.2. Terminology . . . . . . . . . . . . . . . . . . . . . . . 4 2. Differences from OSPF for IPv4 . . . . . . . . . . . . . . . . 5 2.1. Protocol Processing Per-Link, Not Per-Subnet . . . . . . . 5 2.2. Removal of Addressing Semantics . . . . . . . . . . . . . 5 2.3. Addition of Flooding Scope . . . . . . . . . . . . . . . . 6 2.4. Explicit Support for Multiple Instances per Link . . . . . 6 2.5. Use of Link-Local Addresses . . . . . . . . . . . . . . . 7 2.6. Authentication Changes . . . . . . . . . . . . . . . . . . 7 2.7. Packet Format Changes . . . . . . . . . . . . . . . . . . 8 2.8. LSA Format Changes . . . . . . . . . . . . . . . . . . . . 9 2.9. Handling Unknown LSA Types . . . . . . . . . . . . . . . . 10 2.10. Stub/NSSA Area Support . . . . . . . . . . . . . . . . . . 11 2.11. Identifying Neighbors by Router ID . . . . . . . . . . . . 11 3. Differences with RFC 2740 . . . . . . . . . . . . . . . . . . 11 3.1. Support for Multiple Interfaces on the Same Link . . . . . 11 3.2. Deprecation of MOSPF for IPv6 . . . . . . . . . . . . . . 12 3.3. NSSA Specification . . . . . . . . . . . . . . . . . . . . 12 3.4. Stub Area Unknown LSA Flooding Restriction Deprecated . . 12 3.5. Link LSA Suppression . . . . . . . . . . . . . . . . . . . 12 3.6. LSA Options and Prefix Options Updates . . . . . . . . . . 13 3.7. IPv6 Site-Local Addresses . . . . . . . . . . . . . . . . 13 4. Implementation Details . . . . . . . . . . . . . . . . . . . . 13 4.1. Protocol Data Structures . . . . . . . . . . . . . . . . . 14 4.1.1. The Area Data Structure . . . . . . . . . . . . . . . 15 4.1.2. The Interface Data Structure . . . . . . . . . . . . . 15 4.1.3. The Neighbor Data Structure . . . . . . . . . . . . . 16 4.2. Protocol Packet Processing . . . . . . . . . . . . . . . . 17 4.2.1. Sending Protocol Packets . . . . . . . . . . . . . . . 17 4.2.1.1. Sending Hello Packets . . . . . . . . . . . . . . 18 4.2.1.2. Sending Database Description Packets . . . . . . . 19 4.2.2. Receiving Protocol Packets . . . . . . . . . . . . . . 19 4.2.2.1. Receiving Hello Packets . . . . . . . . . . . . . 21 4.3. The Routing table Structure . . . . . . . . . . . . . . . 22 4.3.1. Routing Table Lookup . . . . . . . . . . . . . . . . . 23 4.4. Link State Advertisements . . . . . . . . . . . . . . . . 23 4.4.1. The LSA Header . . . . . . . . . . . . . . . . . . . . 23 4.4.2. The Link-State Database . . . . . . . . . . . . . . . 24 4.4.3. Originating LSAs . . . . . . . . . . . . . . . . . . . 25 4.4.3.1. LSA Options . . . . . . . . . . . . . . . . . . . 27 4.4.3.2. Router-LSAs . . . . . . . . . . . . . . . . . . . 27 Coltun, et al. Standards Track [Page 2]
RFC 5340 OSPF for IPv6 July 2008 4.4.3.3. Network-LSAs . . . . . . . . . . . . . . . . . . . 29 4.4.3.4. Inter-Area-Prefix-LSAs . . . . . . . . . . . . . . 30 4.4.3.5. Inter-Area-Router-LSAs . . . . . . . . . . . . . . 31 4.4.3.6. AS-External-LSAs . . . . . . . . . . . . . . . . . 32 4.4.3.7. NSSA-LSAs . . . . . . . . . . . . . . . . . . . . 33 4.4.3.8. Link-LSAs . . . . . . . . . . . . . . . . . . . . 34 4.4.3.9. Intra-Area-Prefix-LSAs . . . . . . . . . . . . . . 36 4.4.4. Future LSA Validation . . . . . . . . . . . . . . . . 40 4.5. Flooding . . . . . . . . . . . . . . . . . . . . . . . . . 40 4.5.1. Receiving Link State Update Packets . . . . . . . . . 40 4.5.2. Sending Link State Update Packets . . . . . . . . . . 41 4.5.3. Installing LSAs in the Database . . . . . . . . . . . 43 4.6. Definition of Self-Originated LSAs . . . . . . . . . . . . 43 4.7. Virtual Links . . . . . . . . . . . . . . . . . . . . . . 44 4.8. Routing Table Calculation . . . . . . . . . . . . . . . . 44 4.8.1. Calculating the Shortest-Path Tree for an Area . . . . 45 4.8.2. The Next-Hop Calculation . . . . . . . . . . . . . . . 44 4.8.3. Calculating the Inter-Area Routes . . . . . . . . . . 47 4.8.4. Examining Transit Areas' Summary-LSAs . . . . . . . . 48 4.8.5. Calculating AS External and NSSA Routes . . . . . . . 48 4.9. Multiple Interfaces to a Single Link . . . . . . . . . . . 48 4.9.1. Standby Interface State . . . . . . . . . . . . . . . 50 5. Security Considerations . . . . . . . . . . . . . . . . . . . 52 6. Manageability Considerations . . . . . . . . . . . . . . . . . 52 7. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 52 7.1. MOSPF for OSPFv3 Deprecation IANA Considerations . . . . . 53 8. Acknowledgments . . . . . . . . . . . . . . . . . . . . . . . 53 9. References . . . . . . . . . . . . . . . . . . . . . . . . . . 55 9.1. Normative References . . . . . . . . . . . . . . . . . . . 55 9.2. Informative References . . . . . . . . . . . . . . . . . . 56 Appendix A. OSPF Data Formats . . . . . . . . . . . . . . . . . . 57 A.1. Encapsulation of OSPF Packets . . . . . . . . . . . . . . 57 A.2. The Options Field . . . . . . . . . . . . . . . . . . . . 58 A.3. OSPF Packet Formats . . . . . . . . . . . . . . . . . . . 60 A.3.1. The OSPF Packet Header . . . . . . . . . . . . . . . . 60 A.3.2. The Hello Packet . . . . . . . . . . . . . . . . . . . 62 A.3.3. The Database Description Packet . . . . . . . . . . . 63 A.3.4. The Link State Request Packet . . . . . . . . . . . . 65 A.3.5. The Link State Update Packet . . . . . . . . . . . . . 66 A.3.6. The Link State Acknowledgment Packet . . . . . . . . . 67 A.4. LSA Formats . . . . . . . . . . . . . . . . . . . . . . . 68 A.4.1. IPv6 Prefix Representation . . . . . . . . . . . . . . 69 A.4.1.1. Prefix Options . . . . . . . . . . . . . . . . . . 69 A.4.2. The LSA Header . . . . . . . . . . . . . . . . . . . . 70 A.4.2.1. LSA Type . . . . . . . . . . . . . . . . . . . . . 72 A.4.3. Router-LSAs . . . . . . . . . . . . . . . . . . . . . 73 A.4.4. Network-LSAs . . . . . . . . . . . . . . . . . . . . . 76 A.4.5. Inter-Area-Prefix-LSAs . . . . . . . . . . . . . . . . 77 Coltun, et al. Standards Track [Page 3]
RFC 5340 OSPF for IPv6 July 2008 A.4.6. Inter-Area-Router-LSAs . . . . . . . . . . . . . . . . 78 A.4.7. AS-External-LSAs . . . . . . . . . . . . . . . . . . . 79 A.4.8. NSSA-LSAs . . . . . . . . . . . . . . . . . . . . . . 82 A.4.9. Link-LSAs . . . . . . . . . . . . . . . . . . . . . . 82 A.4.10. Intra-Area-Prefix-LSAs . . . . . . . . . . . . . . . . 84 Appendix B. Architectural Constants . . . . . . . . . . . . . . . 86 Appendix C. Configurable Constants . . . . . . . . . . . . . . . 86 C.1. Global Parameters . . . . . . . . . . . . . . . . . . . . 86 C.2. Area Parameters . . . . . . . . . . . . . . . . . . . . . 87 C.3. Router Interface Parameters . . . . . . . . . . . . . . . 88 C.4. Virtual Link Parameters . . . . . . . . . . . . . . . . . 90 C.5. NBMA Network Parameters . . . . . . . . . . . . . . . . . 91 C.6. Point-to-Multipoint Network Parameters . . . . . . . . . . 92 C.7. Host Route Parameters . . . . . . . . . . . . . . . . . . 92 1. Introduction This document describes the modifications to OSPF to support version 6 of the Internet Protocol (IPv6). The fundamental mechanisms of OSPF (flooding, Designated Router (DR) election, area support, (Shortest Path First) SPF calculations, etc.) remain unchanged. However, some changes have been necessary, either due to changes in protocol semantics between IPv4 and IPv6, or simply to handle the increased address size of IPv6. These modifications will necessitate incrementing the protocol version from version 2 to version 3. OSPF for IPv6 is also referred to as OSPF version 3 (OSPFv3). This document is organized as follows. Section 2 describes the differences between OSPF for IPv4 (OSPF version 2) and OSPF for IPv6 (OSPF version 3) in detail. Section 3 describes the difference between RFC 2740 and this document. Section 4 provides implementation details for the changes. Appendix A gives the OSPF for IPv6 packet and Link State Advertisement (LSA) formats. Appendix B lists the OSPF architectural constants. Appendix C describes configuration parameters. 1.1. Requirements Notation The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this document are to be interpreted as described in [RFC-KEYWORDS]. 1.2. Terminology This document attempts to use terms from both the OSPF for IPv4 specification ([OSPFV2]) and the IPv6 protocol specifications ([IPV6]). This has produced a mixed result. Most of the terms used both by OSPF and IPv6 have roughly the same meaning (e.g., Coltun, et al. Standards Track [Page 4]
RFC 5340 OSPF for IPv6 July 2008 interfaces). However, there are a few conflicts. IPv6 uses "link" similarly to IPv4 OSPF's "subnet" or "network". In this case, we have chosen to use IPv6's "link" terminology. "Link" replaces OSPF's "subnet" and "network" in most places in this document, although OSPF's network-LSA remains unchanged (and possibly unfortunately, a new link-LSA has also been created). The names of some of the OSPF LSAs have also changed. See Section 2.8 for details. In the context of this document, an OSPF instance is a separate protocol instance complete with its own protocol data structures (e.g., areas, interfaces, neighbors), link-state database, protocol state machines, and protocol processing (e.g., SPF calculation). 2. Differences from OSPF for IPv4 Most of the algorithms from OSPF for IPv4 [OSPFV2] have been preserved in OSPF for IPv6. However, some changes have been necessary, either due to changes in protocol semantics between IPv4 and IPv6, or simply to handle the increased address size of IPv6. The following subsections describe the differences between this document and [OSPFV2]. 2.1. Protocol Processing Per-Link, Not Per-Subnet IPv6 uses the term "link" to indicate "a communication facility or medium over which nodes can communicate at the link layer" ([IPV6]). "Interfaces" connect to links. Multiple IPv6 subnets can be assigned to a single link, and two nodes can talk directly over a single link, even if they do not share a common IPv6 subnet (IPv6 prefix). For this reason, OSPF for IPv6 runs per-link instead of the IPv4 behavior of per-IP-subnet. The terms "network" and "subnet" used in the IPv4 OSPF specification ([OSPFV2]) should generally be replaced by link. Likewise, an OSPF interface now connects to a link instead of an IP subnet. This change affects the receiving of OSPF protocol packets, the contents of Hello packets, and the contents of network-LSAs. 2.2. Removal of Addressing Semantics In OSPF for IPv6, addressing semantics have been removed from the OSPF protocol packets and the main LSA types, leaving a network- protocol-independent core. In particular: Coltun, et al. Standards Track [Page 5]
RFC 5340 OSPF for IPv6 July 2008 o IPv6 addresses are not present in OSPF packets, except in LSA payloads carried by the Link State Update packets. See Section 2.7 for details. o Router-LSAs and network-LSAs no longer contain network addresses, but simply express topology information. See Section 2.8 for details. o OSPF Router IDs, Area IDs, and LSA Link State IDs remain at the IPv4 size of 32 bits. They can no longer be assigned as (IPv6) addresses. o Neighboring routers are now always identified by Router ID. Previously, they had been identified by an IPv4 address on broadcast, NBMA (Non-Broadcast Multi-Access), and point-to- multipoint links. 2.3. Addition of Flooding Scope Flooding scope for LSAs has been generalized and is now explicitly coded in the LSA's LS type field. There are now three separate flooding scopes for LSAs: o Link-local scope. LSA is only flooded on the local link and no further. Used for the new link-LSA. See Section 4.4.3.8 for details. o Area scope. LSA is only flooded throughout a single OSPF area. Used for router-LSAs, network-LSAs, inter-area-prefix-LSAs, inter- area-router-LSAs, and intra-area-prefix-LSAs. o AS scope. LSA is flooded throughout the routing domain. Used for AS-external-LSAs. A router that originates AS scoped LSAs is considered an AS Boundary Router (ASBR) and will set its E-bit in router-LSAs for regular areas. 2.4. Explicit Support for Multiple Instances per Link OSPF now supports the ability to run multiple OSPF protocol instances on a single link. For example, this may be required on a NAP segment shared between several providers. Providers may be supporting separate OSPF routing domains that wish to remain separate even though they have one or more physical network segments (i.e., links) in common. In OSPF for IPv4, this was supported in a haphazard fashion using the authentication fields in the OSPF for IPv4 header. Coltun, et al. Standards Track [Page 6]
RFC 5340 OSPF for IPv6 July 2008 Another use for running multiple OSPF instances is if you want, for one reason or another, to have a single link belong to two or more OSPF areas. Support for multiple protocol instances on a link is accomplished via an "Instance ID" contained in the OSPF packet header and OSPF interface data structures. Instance ID solely affects the reception of OSPF packets and applies to normal OSPF interfaces and virtual links. 2.5. Use of Link-Local Addresses IPv6 link-local addresses are for use on a single link, for purposes of neighbor discovery, auto-configuration, etc. IPv6 routers do not forward IPv6 datagrams having link-local source addresses [IP6ADDR]. Link-local unicast addresses are assigned from the IPv6 address range FE80/10. OSPF for IPv6 assumes that each router has been assigned link-local unicast addresses on each of the router's attached physical links [IP6ADDR]. On all OSPF interfaces except virtual links, OSPF packets are sent using the interface's associated link-local unicast address as the source address. A router learns the link-local addresses of all other routers attached to its links and uses these addresses as next-hop information during packet forwarding. On virtual links, a global scope IPv6 address MUST be used as the source address for OSPF protocol packets. Link-local addresses appear in OSPF link-LSAs (see Section 4.4.3.8). However, link-local addresses are not allowed in other OSPF LSA types. In particular, link-local addresses MUST NOT be advertised in inter-area-prefix-LSAs (Section 4.4.3.4), AS-external-LSAs (Section 4.4.3.6), NSSA-LSAs (Section 4.4.3.7), or intra-area-prefix- LSAs (Section 4.4.3.9). 2.6. Authentication Changes In OSPF for IPv6, authentication has been removed from the OSPF protocol. The "AuType" and "Authentication" fields have been removed from the OSPF packet header, and all authentication-related fields have been removed from the OSPF area and interface data structures. When running over IPv6, OSPF relies on the IP Authentication Header (see [IPAUTH]) and the IP Encapsulating Security Payload (see [IPESP]) as described in [OSPFV3-AUTH] to ensure integrity and authentication/confidentiality of routing exchanges. Coltun, et al. Standards Track [Page 7]
RFC 5340 OSPF for IPv6 July 2008 Protection of OSPF packet exchanges against accidental data corruption is provided by the standard IPv6 Upper-Layer checksum (as described in Section 8.1 of [IPV6]), covering the entire OSPF packet and prepended IPv6 pseudo-header (see Appendix A.3.1). 2.7. Packet Format Changes OSPF for IPv6 runs directly over IPv6. Aside from this, all addressing semantics have been removed from the OSPF packet headers, making it essentially "network-protocol-independent". All addressing information is now contained in the various LSA types only. In detail, changes in OSPF packet format consist of the following: o The OSPF version number has been incremented from 2 to 3. o The Options field in Hello packets and Database Description packets has been expanded to 24 bits. o The Authentication and AuType fields have been removed from the OSPF packet header (see Section 2.6). o The Hello packet now contains no address information at all. Rather, it now includes an Interface ID that the originating router has assigned to uniquely identify (among its own interfaces) its interface to the link. This Interface ID will be used as the network-LSA's Link State ID if the router becomes the Designated Router on the link. o Two Options bits, the "R-bit" and the "V6-bit", have been added to the Options field for processing router-LSAs during the SPF calculation (see Appendix A.2). If the "R-bit" is clear, an OSPF speaker can participate in OSPF topology distribution without being used to forward transit traffic; this can be used in multi- homed hosts that want to participate in the routing protocol. The V6-bit specializes the R-bit; if the V6-bit is clear, an OSPF speaker can participate in OSPF topology distribution without being used to forward IPv6 datagrams. If the R-bit is set and the V6-bit is clear, IPv6 datagrams are not forwarded but datagrams belonging to another protocol family may be forwarded. o The OSPF packet header now includes an "Instance ID" that allows multiple OSPF protocol instances to be run on a single link (see Section 2.4). Coltun, et al. Standards Track [Page 8]
RFC 5340 OSPF for IPv6 July 2008 2.8. LSA Format Changes All addressing semantics have been removed from the LSA header, router-LSAs, and network-LSAs. These two LSAs now describe the routing domain's topology in a network-protocol-independent manner. New LSAs have been added to distribute IPv6 address information and data required for next-hop resolution. The names of some of IPv4's LSAs have been changed to be more consistent with each other. In detail, changes in LSA format consist of the following: o The Options field has been removed from the LSA header, expanded to 24 bits, and moved into the body of router-LSAs, network-LSAs, inter-area-router-LSAs, and link-LSAs. See Appendix A.2 for details. o The LSA Type field has been expanded (into the former Options space) to 16 bits, with the upper three bits encoding flooding scope and the handling of unknown LSA types (see Section 2.9). o Addresses in LSAs are now expressed as [prefix, prefix length] instead of [address, mask] (see Appendix A.4.1). The default route is expressed as a prefix with length 0. o Router-LSAs and network-LSAs now have no address information and are network protocol independent. o Router interface information MAY be spread across multiple router- LSAs. Receivers MUST concatenate all the router-LSAs originated by a given router when running the SPF calculation. o A new LSA called the link-LSA has been introduced. Link-LSAs have link-local flooding scope; they are never flooded beyond the link with which they are associated. Link-LSAs have three purposes: 1) they provide the router's link-local address to all other routers attached to the link, 2) they inform other routers attached to the link of a list of IPv6 prefixes to associate with the link, and 3) they allow the router to advertise a collection of Options bits to associate with the network-LSA that will be originated for the link. See Section 4.4.3.8 for details. o In IPv4, the router-LSA carries a router's IPv4 interface addresses, the IPv4 equivalent of link-local addresses. These are only used when calculating next hops during the OSPF routing calculation (see Section 16.1.1 of [OSPFV2]), so they do not need to be flooded past the local link. Hence, using link-LSAs to distribute these addresses is more efficient. Note that link- local addresses cannot be learned through the reception of Hellos Coltun, et al. Standards Track [Page 9]
RFC 5340 OSPF for IPv6 July 2008 in all cases. On NBMA links, next-hop routers do not necessarily exchange Hellos. Rather, these routers learn of each other's existence by way of the Designated Router (DR). o The Options field in the network LSA is set to the logical OR of the Options that each router on the link advertises in its link- LSA. o Type-3 summary-LSAs have been renamed "inter-area-prefix-LSAs". Type-4 summary LSAs have been renamed "inter-area-router-LSAs". o The Link State ID in inter-area-prefix-LSAs, inter-area-router- LSAs, NSSA-LSAs, and AS-external-LSAs has lost its addressing semantics and now serves solely to identify individual pieces of the Link State Database. All addresses or Router IDs that were formerly expressed by the Link State ID are now carried in the LSA bodies. o Network-LSAs and link-LSAs are the only LSAs whose Link State ID carries additional meaning. For these LSAs, the Link State ID is always the Interface ID of the originating router on the link being described. For this reason, network-LSAs and link-LSAs are now the only LSAs whose size cannot be limited: a network-LSA MUST list all routers connected to the link and a link-LSA MUST list all of a router's addresses on the link. o A new LSA called the intra-area-prefix-LSA has been introduced. This LSA carries all IPv6 prefix information that in IPv4 is included in router-LSAs and network-LSAs. See Section 4.4.3.9 for details. o Inclusion of a forwarding address or external route tag in AS- external-LSAs is now optional. In addition, AS-external-LSAs can now reference another LSA, for inclusion of additional route attributes that are outside the scope of the OSPF protocol. For example, this reference could be used to attach BGP path attributes to external routes. 2.9. Handling Unknown LSA Types Handling of unknown LSA types has been made more flexible so that, based on the LS type, unknown LSA types are either treated as having link-local flooding scope, or are stored and flooded as if they were understood. This behavior is explicitly coded in the LSA Handling bit of the link state header's LS type field (see the U-bit in Appendix A.4.2.1). Coltun, et al. Standards Track [Page 10]
RFC 5340 OSPF for IPv6 July 2008 The IPv4 OSPF behavior of simply discarding unknown types is unsupported due to the desire to mix router capabilities on a single link. Discarding unknown types causes problems when the Designated Router supports fewer options than the other routers on the link. 2.10. Stub/NSSA Area Support In OSPF for IPv4, stub and NSSA areas were designed to minimize link- state database and routing table sizes for the areas' internal routers. This allows routers with minimal resources to participate in even very large OSPF routing domains. In OSPF for IPv6, the concept of stub and NSSA areas is retained. In IPv6, of the mandatory LSA types, stub areas carry only router-LSAs, network-LSAs, inter-area-prefix-LSAs, link-LSAs, and intra-area- prefix-LSAs. NSSA areas are restricted to these types and, of course, NSSA-LSAs. This is the IPv6 equivalent of the LSA types carried in IPv4 stub areas: router-LSAs, network-LSAs, type 3 summary-LSAs and for NSSA areas: stub area types and NSSA-LSAs. 2.11. Identifying Neighbors by Router ID In OSPF for IPv6, neighboring routers on a given link are always identified by their OSPF Router ID. This contrasts with the IPv4 behavior where neighbors on point-to-point networks and virtual links are identified by their Router IDs while neighbors on broadcast, NBMA, and point-to-multipoint links are identified by their IPv4 interface addresses. This change affects the reception of OSPF packets (see Section 8.2 of [OSPFV2]), the lookup of neighbors (Section 10 of [OSPFV2]), and the reception of Hello packets (Section 10.5 of [OSPFV2]). The Router ID of 0.0.0.0 is reserved and SHOULD NOT be used. 3. Differences with RFC 2740 OSPFv3 implementations based on RFC 2740 will fully interoperate with implementations based on this specification. There are, however, some protocol additions and changes (all of which are backward compatible). 3.1. Support for Multiple Interfaces on the Same Link This protocol feature was only partially specified in the RFC 2740. The level of specification was insufficient to implement the feature. Section 4.9 specifies the additions and clarifications necessary for implementation. They are fully compatible with RFC 2740. Coltun, et al. Standards Track [Page 11]
RFC 5340 OSPF for IPv6 July 2008 3.2. Deprecation of MOSPF for IPv6 This protocol feature was only partially specified in RFC 2740. The level of specification was insufficient to implement the feature. There are no known implementations. Multicast Extensions to OSPF (MOSPF) support and its attendant protocol fields have been deprecated from OSPFv3. Refer to Section 4.4.3.2, Section 4.4.3.4, Section 4.4.3.6, Section 4.4.3.7, Appendix A.2, Appendix A.4.2.1, Appendix A.4.3, Appendix A.4.1.1, and Section 7.1. 3.3. NSSA Specification This protocol feature was only partially specified in RFC 2740. The level of specification was insufficient to implement the function. This document includes an NSSA specification unique to OSPFv3. This specification coupled with [NSSA] provide sufficient specification for implementation. Refer to Section 4.8.5, Appendix A.4.3, Appendix A.4.8, and [NSSA]. 3.4. Stub Area Unknown LSA Flooding Restriction Deprecated In RFC 2740 [OSPFV3], flooding of unknown LSA was restricted within stub and NSSA areas. The text describing this restriction is included below. However, unlike in IPv4, IPv6 allows LSAs with unrecognized LS types to be labeled "Store and flood the LSA, as if type understood" (see the U-bit in Appendix A.4.2.1). Uncontrolled introduction of such LSAs could cause a stub area's link-state database to grow larger than its component routers' capacities. To guard against this, the following rule regarding stub areas has been established: an LSA whose LS type is unrecognized can only be flooded into/throughout a stub area if both a) the LSA has area or link-local flooding scope and b) the LSA has U-bit set to 0. See Section 3.5 for details. This restriction has been deprecated. OSPFv3 routers will flood link and area scope LSAs whose LS type is unrecognized and whose U-bit is set to 1 throughout stub and NSSA areas. There are no backward- compatibility issues other than OSPFv3 routers still supporting the restriction may not propagate newly defined LSA types. 3.5. Link LSA Suppression The LinkLSASuppression interface configuration parameter has been added. If LinkLSASuppression is configured for an interface and the interface type is not broadcast or NBMA, origination of the link-LSA Coltun, et al. Standards Track [Page 12]
RFC 5340 OSPF for IPv6 July 2008 may be suppressed. The LinkLSASuppression interface configuration parameter is described in Appendix C.3. Section 4.8.2 and Section 4.4.3.8 were updated to reflect the parameter's usage. 3.6. LSA Options and Prefix Options Updates The LSA Options and Prefix Options fields have been updated to reflect recent protocol additions. Specifically, bits related to MOSPF have been deprecated, Options field bits common with OSPFv2 have been reserved, and the DN-bit has been added to the prefix- options. Refer to Appendix A.2 and Appendix A.4.1.1. 3.7. IPv6 Site-Local Addresses All references to IPv6 site-local addresses have been removed. 4. Implementation Details When going from IPv4 to IPv6, the basic OSPF mechanisms remain unchanged from those documented in [OSPFV2]. These mechanisms are briefly outlined in Section 4 of [OSPFV2]. Both IPv6 and IPv4 have a link-state database composed of LSAs and synchronized between adjacent routers. Initial synchronization is performed through the Database Exchange process, which includes the exchange of Database Description, Link State Request, and Link State Update packets. Thereafter, database synchronization is maintained via flooding, utilizing Link State Update and Link State Acknowledgment packets. Both IPv6 and IPv4 use OSPF Hello packets to discover and maintain neighbor relationships, as well as to elect Designated Routers and Backup Designated Routers on broadcast and NBMA links. The decision as to which neighbor relationships become adjacencies, and the basic ideas behind inter-area routing, importing external information in AS-external-LSAs, and the various routing calculations are also the same. In particular, the following IPv4 OSPF functionality described in [OSPFV2] remains completely unchanged for IPv6: o Both IPv4 and IPv6 use OSPF packet types described in Section 4.3 of [OSPFV2], namely: Hello, Database Description, Link State Request, Link State Update, and Link State Acknowledgment packets. While in some cases (e.g., Hello packets) their format has changed somewhat, the functions of the various packet types remain the same. Coltun, et al. Standards Track [Page 13]
RFC 5340 OSPF for IPv6 July 2008 o The system requirements for an OSPF implementation remain unchanged, although OSPF for IPv6 requires an IPv6 protocol stack (from the network layer on down) since it runs directly over the IPv6 network layer. o The discovery and maintenance of neighbor relationships, and the selection and establishment of adjacencies, remain the same. This includes election of the Designated Router and Backup Designated Router on broadcast and NBMA links. These mechanisms are described in Sections 7, 7.1, 7.2, 7.3, 7.4, and 7.5 of [OSPFV2]. o The link types (or equivalently, interface types) supported by OSPF remain unchanged, namely: point-to-point, broadcast, NBMA, point-to-multipoint, and virtual links. o The interface state machine, including the list of OSPF interface states and events, and the Designated Router and Backup Designated Router election algorithm remain unchanged. These are described in Sections 9.1, 9.2, 9.3, and 9.4 of [OSPFV2]. o The neighbor state machine, including the list of OSPF neighbor states and events, remains unchanged. The neighbor state machine is described in Sections 10.1, 10.2, 10.3, and 10.4 of [OSPFV2]. o Aging of the link-state database, as well as flushing LSAs from the routing domain through the premature aging process, remains unchanged from the description in Sections 14 and 14.1 of [OSPFV2]. However, some OSPF protocol mechanisms have changed as previously described in Section 2 herein. These changes are explained in detail in the following subsections, making references to the appropriate sections of [OSPFV2]. The following subsections provide a recipe for turning an IPv4 OSPF implementation into an IPv6 OSPF implementation. 4.1. Protocol Data Structures The major OSPF data structures are the same for both IPv4 and IPv6: areas, interfaces, neighbors, the link-state database, and the routing table. The top-level data structures for IPv6 remain those listed in Section 5 of [OSPFV2], with the following modifications: o All LSAs with known LS type and AS flooding scope appear in the top-level data structure, instead of belonging to a specific area or link. AS-external-LSAs are the only LSAs defined by this specification that have AS flooding scope. LSAs with unknown LS Coltun, et al. Standards Track [Page 14]
RFC 5340 OSPF for IPv6 July 2008 type, U-bit set to 1 (flood even when unrecognized), and AS flooding scope also appear in the top-level data structure. 4.1.1. The Area Data Structure The IPv6 area data structure contains all elements defined for IPv4 areas in Section 6 of [OSPFV2]. In addition, all LSAs of known type that have area flooding scope are contained in the IPv6 area data structure. This always includes the following LSA types: router- LSAs, network-LSAs, inter-area-prefix-LSAs, inter-area-router-LSAs, and intra-area-prefix-LSAs. LSAs with unknown LS type, U-bit set to 1 (flood even when unrecognized), and area scope also appear in the area data structure. NSSA-LSAs are also included in an NSSA area's data structure. 4.1.2. The Interface Data Structure In OSPF for IPv6, an interface connects a router to a link. The IPv6 interface structure modifies the IPv4 interface structure (as defined in Section 9 of [OSPFV2]) as follows: Interface ID Every interface is assigned an Interface ID, which uniquely identifies the interface with the router. For example, some implementations MAY be able to use the MIB-II IfIndex ([INTFMIB]) as the Interface ID. The Interface ID appears in Hello packets sent out the interface, the link-local-LSA originated by the router for the attached link, and the router-LSA originated by the router-LSA for the associated area. It will also serve as the Link State ID for the network-LSA that the router will originate for the link if the router is elected Designated Router. The Interface ID for a virtual link is independent of the Interface ID of the outgoing interface it traverses in the transit area. Instance ID Every interface is assigned an Instance ID. This should default to 0. It is only necessary to assign a value other than 0 on those links that will contain multiple separate communities of OSPF routers. For example, suppose that there are two communities of routers on a given ethernet segment that you wish to keep separate. The first community is assigned an Instance ID of 0 and all the routers in the first community will be assigned 0 as the Instance ID for interfaces connected to the ethernet segment. An Instance ID of 1 is assigned to the other routers' interfaces connected to the ethernet segment. The OSPF transmit and receive processing (see Section 4.2) will then keep the two communities separate. Coltun, et al. Standards Track [Page 15]
RFC 5340 OSPF for IPv6 July 2008 List of LSAs with link-local scope All LSAs with link-local scope and that were originated/flooded on the link belong to the interface structure that connects to the link. This includes the collection of the link's link-LSAs. IP interface address For IPv6, the IPv6 address appearing in the source of OSPF packets sent on the interface is almost always a link-local address. The one exception is for virtual links that MUST use one of the router's own global IPv6 addresses as IP interface address. List of link prefixes A list of IPv6 prefixes can be configured for the attached link. These will be advertised by the router in link-LSAs, so that they can be advertised by the link's Designated Router in intra-area- prefix-LSAs. In OSPF for IPv6, each router interface has a single metric representing the cost of sending packets on the interface. In addition, OSPF for IPv6 relies on the IP Authentication Header (see [IPAUTH]) and the IP Encapsulating Security Payload (see [IPESP]) as described in [OSPFV3-AUTH] to ensure integrity and authentication/ confidentiality of routing exchanges. For this reason, AuType and Authentication key are not associated with IPv6 OSPF interfaces. Interface states, events, and the interface state machine remain unchanged from IPv4 as documented in Sections 9.1, 9.2, and 9.3 of [OSPFV2] respectively. The Designated Router and Backup Designated Router election algorithm also remains unchanged from the IPv4 election in Section 9.4 of [OSPFV2]. 4.1.3. The Neighbor Data Structure The neighbor structure performs the same function in both IPv6 and IPv4. Namely, it collects all information required to form an adjacency between two routers when such an adjacency becomes necessary. Each neighbor structure is bound to a single OSPF interface. The differences between the IPv6 neighbor structure and the neighbor structure defined for IPv4 in Section 10 of [OSPFV2] are: Neighbor's Interface ID The Interface ID that the neighbor advertises in its Hello packets must be recorded in the neighbor structure. The router will include the neighbor's Interface ID in the router's router-LSA when either a) advertising a point-to-point or point-to-multipoint link to the neighbor or b) advertising a link to a network where the neighbor has become the Designated Router. Coltun, et al. Standards Track [Page 16]
RFC 5340 OSPF for IPv6 July 2008 Neighbor IP address The neighbor's IPv6 address contained as the source address in OSPF for IPv6 packets. This will be an IPv6 link-local address for all link types except virtual links. Neighbor's Designated Router The neighbor's choice of Designated Router is now encoded as a Router ID instead of as an IP address. Neighbor's Backup Designated Router The neighbor's choice of Backup Designated Router is now encoded as a Router ID instead of as an IP address. Neighbor states, events, and the neighbor state machine remain unchanged from IPv4 as documented in Sections 10.1, 10.2, and 10.3 of [OSPFV2] respectively. The decision as to which adjacencies to form also remains unchanged from the IPv4 logic documented in Section 10.4 of [OSPFV2]. 4.2. Protocol Packet Processing OSPF for IPv6 runs directly over IPv6's network layer. As such, it is encapsulated in one or more IPv6 headers with the Next Header field of the immediately encapsulating IPv6 header set to the value 89. As for OSPF for IPv4, OSPF for IPv6 OSPF routing protocol packets are sent along adjacencies only (with the exception of Hello packets, which are used to discover the adjacencies). OSPF packet types and functions are the same in both IPv4 and IPv6, encoded by the Type field of the standard OSPF packet header. 4.2.1. Sending Protocol Packets When an IPv6 router sends an OSPF routing protocol packet, it fills in the fields of the standard OSPF for IPv6 packet header (see Appendix A.3.1) as follows: Version # Set to 3, the version number of the protocol as documented in this specification. Type The type of OSPF packet, such as Link State Update or Hello packet. Coltun, et al. Standards Track [Page 17]
RFC 5340 OSPF for IPv6 July 2008 Packet length The length of the entire OSPF packet in bytes, including the standard OSPF packet header. Router ID The identity of the router itself (who is originating the packet). Area ID The OSPF area for the interface on which the packet is being sent. Instance ID The OSPF Instance ID associated with the interface out of which the packet is being sent. Checksum The standard IPv6 Upper-Layer checksum (as described in Section 8.1 of [IPV6]) covering the entire OSPF packet and prepended IPv6 pseudo-header (see Appendix A.3.1). Selection of OSPF routing protocol packets' IPv6 source and destination addresses is performed identically to the IPv4 logic in Section 8.1 of [OSPFV2]. The IPv6 destination address is chosen from among the addresses AllSPFRouters, AllDRouters, and the Neighbor IP address associated with the other end of the adjacency (which in IPv6, for all links except virtual links, is an IPv6 link-local address). The sending of Link State Request packets and Link State Acknowledgment packets remains unchanged from the IPv4 procedures documented in Sections 10.9 and 13.5 of [OSPFV2] respectively. Sending Hello packets is documented in Section 4.2.1.1, and the sending of Database Description packets in Section 4.2.1.2. The sending of Link State Update packets is documented in Section 4.5.2. 4.2.1.1. Sending Hello Packets IPv6 changes the way OSPF Hello packets are sent in the following ways (compare to Section 9.5 of [OSPFV2]): o Before the Hello packet is sent on an interface, the interface's Interface ID MUST be copied into the Hello packet. o The Hello packet no longer contains an IP network mask since OSPF for IPv6 runs per-link instead of per-subnet. o The choice of Designated Router and Backup Designated Router is now indicated within Hellos by their Router IDs instead of by their IP interface addresses. Advertising the Designated Router Coltun, et al. Standards Track [Page 18]
RFC 5340 OSPF for IPv6 July 2008 (or Backup Designated Router) as 0.0.0.0 indicates that the Designated Router (or Backup Designated Router) has not yet been chosen. o The Options field within Hello packets has moved around, getting larger in the process. More Options bits are now possible. Those that MUST be set correctly in Hello packets are as follows. The E-bit is set if and only if the interface attaches to a regular area, i.e., not a stub or NSSA area. Similarly, the N-bit is set if and only if the interface attaches to an NSSA area (see [NSSA]). Finally, the DC-bit is set if and only if the router wishes to suppress the sending of future Hellos over the interface (see [DEMAND]). Unrecognized bits in the Hello packet's Options field should be cleared. Sending Hello packets on NBMA networks proceeds for IPv6 in exactly the same way as for IPv4, as documented in Section 9.5.1 of [OSPFV2]. 4.2.1.2. Sending Database Description Packets The sending of Database Description packets differs from Section 10.8 of [OSPFV2] in the following ways: o The Options field within Database Description packets has moved around, getting larger in the process. More Options bits are now possible. Those that MUST be set correctly in Database Description packets are as follows. The DC-bit is set if and only if the router wishes to suppress the sending of Hellos over the interface (see [DEMAND]). Unrecognized bits in the Database Description packet's Options field should be cleared. 4.2.2. Receiving Protocol Packets Whenever a router receives an OSPF protocol packet, it is marked with the interface on which it was received. For routers that have virtual links configured, it may not be immediately obvious with which interface to associate the packet. For example, consider the Router RT11 depicted in Figure 6 of [OSPFV2]. If RT11 receives an OSPF protocol packet on its interface to Network N8, it may want to associate the packet with the interface to Area 2, or with the virtual link to Router RT10 (which is part of the backbone). In the following, we assume that the packet is initially associated with the non-virtual link. In order for the packet to be passed to OSPF for processing, the following tests must be performed on the encapsulating IPv6 headers: Coltun, et al. Standards Track [Page 19]
RFC 5340 OSPF for IPv6 July 2008 o The packet's IP destination address MUST be one of the IPv6 unicast addresses associated with the receiving interface (this includes link-local addresses), one of the IPv6 multicast addresses AllSPFRouters or AllDRouters, or an IPv6 global address (for virtual links). o The Next Header field of the immediately encapsulating IPv6 header MUST specify the OSPF protocol (89). o Any encapsulating IP Authentication Headers (see [IPAUTH]) and the IP Encapsulating Security Payloads (see [IPESP]) MUST be processed and/or verified to ensure integrity and authentication/ confidentiality of OSPF routing exchanges. This is described in [OSPFV3-AUTH]. After processing the encapsulating IPv6 headers, the OSPF packet header is processed. The fields specified in the header must match those configured for the receiving OSPFv3 interface. If they do not, the packet SHOULD be discarded: o The version number field MUST specify protocol version 3. o The IPv6 Upper-Layer checksum (as described in Section 8.1 of [IPV6]), covering the entire OSPF packet and prepended IPv6 pseudo-header, must be verified (see Appendix A.3.1). o The Area ID and Instance ID found in the OSPF header must be verified. If both of the following cases fail, the packet should be discarded. The Area ID and Instance ID specified in the header must either: 1. Match one of the Area ID(s) and Interface Instance ID(s) for the receiving link. Unlike IPv4, the IPv6 source address is not restricted to lie within the same IPv6 subnet as the receiving link. IPv6 OSPF runs per-link instead of per-IP- subnet. 2. Match the backbone area and other criteria for a configured virtual link. The receiving router must be an ABR (Area Border Router) and the Router ID specified in the packet (the source router) must be the other end of a configured virtual link. Additionally, the receiving link must have an OSPFv3 interface that attaches to the virtual link's configured transit area and the Instance ID must match the virtual link's Instance ID. If all of these checks succeed, the packet is accepted and is associated with the virtual link (and the backbone area). Coltun, et al. Standards Track [Page 20]
RFC 5340 OSPF for IPv6 July 2008 o Locally originated packets SHOULD NOT be processed by OSPF except for support of multiple interfaces attached to the same link as described in Section 4.9. Locally originated packets have a source address equal to one of the router's local addresses. o Packets whose IPv6 destination is AllDRouters should only be accepted if the state of the receiving OSPFv3 interface is DR or Backup (see Section 9.1 [OSPFV2]). After header processing, the packet is further processed according to its OSPF packet type. OSPF packet types and functions are the same for both IPv4 and IPv6. If the packet type is Hello, it should then be further processed by the Hello packet processing as described in Section 4.2.2.1. All other packet types are sent/received only on adjacencies. This means that the packet must have been sent by one of the router's active neighbors. The neighbor is identified by the Router ID appearing in the received packet's OSPF header. Packets not matching any active neighbor are discarded. The receive processing of Database Description packets, Link State Request packets, and Link State Acknowledgment packets is almost identical to the IPv4 procedures documented in Sections 10.6, 10.7, and 13.7 of [OSPFV2] respectively with the exceptions noted below. o LSAs with unknown LS types in Database Description packets that have an acceptable flooding scope are processed the same as LSAs with known LS types. In OSPFv2 [OSPFV2], these would result in the adjacency being brought down with a SequenceMismatch event. The receiving of Hello packets is documented in Section 4.2.2.1 and the receiving of Link State Update packets is documented in Section 4.5.1. 4.2.2.1. Receiving Hello Packets The receive processing of Hello packets differs from Section 10.5 of [OSPFV2] in the following ways: o On all link types (e.g., broadcast, NBMA, point-to-point, etc.), neighbors are identified solely by their OSPF Router ID. For all link types except virtual links, the Neighbor IP address is set to the IPv6 source address in the IPv6 header of the received OSPF Hello packet. o There is no longer a Network Mask field in the Hello packet. Coltun, et al. Standards Track [Page 21]
RFC 5340 OSPF for IPv6 July 2008 o The neighbor's choice of Designated Router and Backup Designated Router is now encoded as an OSPF Router ID instead of an IP interface address. 4.3. The Routing table Structure The routing table used by OSPF for IPv4 is defined in Section 11 of [OSPFV2]. For IPv6, there are analogous routing table entries: there are routing table entries for IPv6 address prefixes and also for AS boundary routers. The latter routing table entries are only used to hold intermediate results during the routing table build process (see Section 4.8). Also, to hold the intermediate results during the shortest-path calculation for each area, there is a separate routing table for each area holding the following entries: o An entry for each router in the area. Routers are identified by their OSPF Router ID. These routing table entries hold the set of shortest paths through a given area to a given router, which in turn allows calculation of paths to the IPv6 prefixes advertised by that router in intra-area-prefix-LSAs. If the router is also an area border router, these entries are also used to calculate paths for inter-area address prefixes. If in addition the router is the other endpoint of a virtual link, the routing table entry describes the cost and viability of the virtual link. o An entry for each transit link in the area. Transit links have associated network-LSAs. Both the transit link and the network- LSA are identified by a combination of the Designated Router's Interface ID on the link and the Designated Router's OSPF Router ID. These routing table entries allow later calculation of paths to IP prefixes advertised for the transit link in intra-area- prefix-LSAs. The fields in the IPv4 OSPF routing table (see Section 11 of [OSPFV2]) remain valid for IPv6: optional capabilities (routers only), path type, cost, type 2 cost, link state origin, and for each of the equal cost paths to the destination, the next-hop and advertising routers. For IPv6, the link-state origin field in the routing table entry is the router-LSA or network-LSA that has directly or indirectly produced the routing table entry. For example, if the routing table entry describes a route to an IPv6 prefix, the link state origin is the router-LSA or network-LSA that is listed in the body of the intra-area-prefix-LSA that has produced the route (see Appendix A.4.10). Coltun, et al. Standards Track [Page 22]
RFC 5340 OSPF for IPv6 July 2008 4.3.1. Routing Table Lookup Routing table lookup (i.e., determining the best matching routing table entry during IP forwarding) is the same for IPv6 as for IPv4. 4.4. Link State Advertisements For IPv6, the OSPF LSA header has changed slightly, with the LS type field expanding and the Options field being moved into the body of appropriate LSAs. Also, the formats of some LSAs have changed somewhat (namely, router-LSAs, network-LSAs, AS-external-LSAs, and NSSA-LSAs), while the names of other LSAs have been changed (type 3 and 4 summary-LSAs are now inter-area-prefix-LSAs and inter-area- router-LSAs respectively) and additional LSAs have been added (link- LSAs and intra-area-prefix-LSAs). Type of Service (TOS) has been removed from the OSPFv2 specification [OSPFV2] and is not encoded within OSPF for IPv6's LSAs. These changes will be described in detail in the following subsections. 4.4.1. The LSA Header In both IPv4 and IPv6, all OSPF LSAs begin with a standard 20-byte LSA header. However, the contents of this 20-byte header have changed in IPv6. The LS age, Advertising Router, LS Sequence Number, LS checksum, and length fields within the LSA header remain unchanged, as documented in Sections 12.1.1, 12.1.5, 12.1.6, 12.1.7, and A.4.1 of [OSPFV2], respectively. However, the following fields have changed for IPv6: Options The Options field has been removed from the standard 20-byte LSA header and moved into the body of router-LSAs, network-LSAs, inter-area-router-LSAs, and link-LSAs. The size of the Options field has increased from 8 to 24 bits, and some of the bit definitions have changed (see Appendix A.2). Additionally, a separate PrefixOptions field, 8 bits in length, is attached to each prefix advertised within the body of an LSA. LS type The size of the LS type field has increased from 8 to 16 bits, with high-order bit encoding the handling of unknown types and the next two bits encoding flooding scope. See Appendix A.4.2.1 for the current coding of the LS type field. Coltun, et al. Standards Track [Page 23]
RFC 5340 OSPF for IPv6 July 2008 Link State ID The Link State ID remains at 32 bits in length. However, except for network-LSAs and link-LSAs, the Link State ID has shed any addressing semantics. For example, an IPv6 router originating multiple AS-external-LSAs could start by assigning the first a Link State ID of 0.0.0.1, the second a Link State ID of 0.0.0.2, and so on. Instead of the IPv4 behavior of encoding the network number within the AS-external-LSA's Link State ID, the IPv6 Link State ID simply serves as a way to differentiate multiple LSAs originated by the same router. For network-LSAs, the Link State ID is set to the Designated Router's Interface ID on the link. When a router originates a link-LSA for a given link, its Link State ID is set equal to the router's Interface ID on the link. 4.4.2. The Link-State Database In IPv6, as in IPv4, individual LSAs are identified by a combination of their LS type, Link State ID, and Advertising Router fields. Given two instances of an LSA, the most recent instance is determined by examining the LSAs' LS sequence number, using LS checksum and LS age as tiebreakers (see Section 13.1 of [OSPFV2]). In IPv6, the link-state database is split across three separate data structures. LSAs with AS flooding scope are contained within the top-level OSPF data structure (see Section 4.1) as long as either their LS type is known or their U-bit is 1 (flood even when unrecognized); this includes the AS-external-LSAs. LSAs with area flooding scope are contained within the appropriate area structure (see Section 4.1.1) as long as either their LS type is known or their U-bit is 1 (flood even when unrecognized); this includes router-LSAs, network-LSAs, inter-area-prefix-LSAs, inter-area-router-LSAs, NSSA- LSAs, and intra-area-prefix-LSAs. LSAs with an unknown LS type, the U-bit set to 0, and/or link-local flooding scope are contained within the appropriate interface structure (see Section 4.1.2); this includes link-LSAs. To look up or install an LSA in the database, you first examine the LS type and the LSA's context (i.e., the area or link to which the LSA belongs). This information allows you to find the correct database of LSAs where you then search based on the LSA's type, Link State ID, and Advertising Router. Coltun, et al. Standards Track [Page 24]
RFC 5340 OSPF for IPv6 July 2008 4.4.3. Originating LSAs The process of reoriginating an LSA in IPv6 is the same as in IPv4: the LSA's LS sequence number is incremented, its LS age is set to 0, its LS checksum is calculated, and the LSA is added to the link state database and flooded on the appropriate interfaces. The list of events causing LSAs to be reoriginated for IPv4 is given in Section 12.4 of [OSPFV2]. The following events and/or actions are added for IPv6: o The state or interface ID of one of the router's interfaces changes. The router may need to (re)originate or flush its link- LSA and one or more router-LSAs and/or intra-area-prefix-LSAs. If the router is the Designated Router, the router may also need to (re)originate and/or flush the network-LSA corresponding to the interface. o The identity of a link's Designated Router changes. The router may need to (re)originate or flush the link's network-LSA and one or more router-LSAs and/or intra-area-prefix-LSAs. o A neighbor transitions to/from "Full" state. The router may need to (re)originate or flush the link's network-LSA and one or more router-LSAs and/or intra-area-prefix-LSAs. o The Interface ID of a neighbor changes. This may cause a new instance of a router-LSA to be originated for the associated area. o A new prefix is added to an attached link, or a prefix is deleted (both through configuration). This causes the router to reoriginate its link-LSA for the link or, if it is the only router attached to the link, causes the router to reoriginate an intra- area-prefix-LSA. o A new link-LSA is received, causing the link's collection of prefixes to change. If the router is the Designated Router for the link, it originates a new intra-area-prefix-LSA. o A new link-LSA is received, causing the logical OR of LSA options advertised by adjacent routers on the link to change. If the router is the Designated Router for the link, it originates a new network-LSA. Detailed construction of the seven required IPv6 LSA types is supplied by the following subsections. In order to display example LSAs, the network map in Figure 15 of [OSPFV2] has been reworked to show IPv6 addressing, resulting in Figure 1. The OSPF cost of each Coltun, et al. Standards Track [Page 25]
RFC 5340 OSPF for IPv6 July 2008 interface is displayed in Figure 1. The assignment of IPv6 prefixes to network links is shown in Table 1. A single area address range has been configured for Area 1, so that outside of Area 1 all of its prefixes are covered by a single route to 2001:0db8:c001::/48. The OSPF interface IDs and the link-local addresses for the router interfaces in Figure 1 are given in Table 2. .......................................... . Area 1. . + . . | . . | 3+---+1 . . N1 |--|RT1|-----+ . . | +---+ \ . . | \ ______ . . + \/ \ 1+---+ . * N3 *------|RT4|------ . + /\_______/ +---+ . | / | . . | 3+---+1 / | . . N2 |--|RT2|-----+ 1| . . | +---+ +---+ . . | |RT3|---------------- . + +---+ . . |2 . . | . . +------------+ . . N4 . .......................................... Figure 1: Area 1 with IP Addresses Shown Network IPv6 prefix ----------------------------------- N1 2001:0db8:c001:0200::/56 N2 2001:0db8:c001:0300::/56 N3 2001:0db8:c001:0100::/56 N4 2001:0db8:c001:0400::/56 Table 1: IPv6 Link Prefixes for Sample Network Coltun, et al. Standards Track [Page 26]
RFC 5340 OSPF for IPv6 July 2008 Router Interface Interface ID link-local address ------------------------------------------------------- RT1 to N1 1 fe80:0001::RT1 to N3 2 fe80:0002::RT1 RT2 to N2 1 fe80:0001::RT2 to N3 2 fe80:0002::RT2 RT3 to N3 1 fe80:0001::RT3 to N4 2 fe80:0002::RT3 RT4 to N3 1 fe80:0001::RT4 Table 2: OSPF Interface IDs and Link-Local Addresses Figure 1 4.4.3.1. LSA Options The Options field in LSAs should be coded as follows. The V6-bit should be set unless the router will not participate in transit IPv6 routing. The E-bit should be clear if and only if the attached area is an OSPF stub or OSPF NSSA area. The E-bit should always be set in AS scoped LSAs. The N-bit should be set if and only if the attached area is an OSPF NSSA area. The R-bit should be set unless the router will not participate in any transit routing. The DC-bit should be set if and only if the router can correctly process the DoNotAge bit when it appears in the LS age field of LSAs (see [DEMAND]). All unrecognized bits in the Options field should be cleared. The V6-bit and R-bit are only examined in Router-LSAs during the SPF computation. In other LSA types containing options, they are set for informational purposes only. 4.4.3.2. Router-LSAs The LS type of a router-LSA is set to the value 0x2001. Router-LSAs have area flooding scope. A router MAY originate one or more router- LSAs for a given area. Each router-LSA contains an integral number of interface descriptions. Taken together, the collection of router- LSAs originated by the router for an area describes the collected states of all the router's interfaces attached to the area. When multiple router-LSAs are used, they are distinguished by their Link State ID fields. To the left of the Options field, the router capability bits V, E, and B should be set according to Section 12.4.1 of [OSPFV2]. Each of the router's interfaces to the area is then described by appending "link descriptions" to the router-LSA. Each link description is 16 bytes long, consisting of five fields: (link) Type, Coltun, et al. Standards Track [Page 27]
RFC 5340 OSPF for IPv6 July 2008 Metric, Interface ID, Neighbor Interface ID, and Neighbor Router ID (see Appendix A.4.3). Interfaces in the state "Down" or "Loopback" are not described (although looped back interfaces can contribute prefixes to intra-area-prefix-LSAs), nor are interfaces without any full adjacencies described (except in the case of multiple Standby Interfaces as described in Section 4.9). All other interfaces to the area add zero, one, or more link descriptions. The number and content of these depend on the interface type. Within each link description, the Metric field is always set to the interface's output cost, and the Interface ID field is set to the interface's OSPF Interface ID. Point-to-point interfaces If the neighboring router is fully adjacent, add a Type 1 link description (point-to-point). The Neighbor Interface ID field is set to the Interface ID advertised by the neighbor in its Hello packets, and the Neighbor Router ID field is set to the neighbor's Router ID. Broadcast and NBMA interfaces If the router is fully adjacent to the link's Designated Router or if the router itself is the Designated Router and is fully adjacent to at least one other router, add a single Type 2 link description (transit network). The Neighbor Interface ID field is set to the Interface ID advertised by the Designated Router in its Hello packets, and the Neighbor Router ID field is set to the Designated Router's Router ID. Virtual links If the neighboring router is fully adjacent, add a Type 4 link description (virtual). The Neighbor Interface ID field is set to the Interface ID advertised by the neighbor in its Hello packets, and the Neighbor Router ID field is set to the neighbor's Router ID. Note that the output cost of a virtual link is calculated during the routing table calculation (see Section 4.7). Point-to-Multipoint interfaces For each fully adjacent neighbor associated with the interface, add a separate Type 1 link description (point-to-point) with the Neighbor Interface ID field set to the Interface ID advertised by the neighbor in its Hello packets and the Neighbor Router ID field set to the neighbor's Router ID. As an example, consider the router-LSA that router RT3 would originate for Area 1 in Figure 1. Only a single interface must be described, namely, that which connects to the transit network N3. It assumes that RT4 has been elected the Designated Router of Network N3. Coltun, et al. Standards Track [Page 28]
RFC 5340 OSPF for IPv6 July 2008 ; RT3's router-LSA for Area 1 LS age = 0 ;newly (re)originated LS type = 0x2001 ;router-LSA Link State ID = 0 ;first fragment Advertising Router = 192.0.2.3 ;RT3's Router ID bit E = 0 ;not an AS boundary router bit B = 1 ;area border router Options = (V6-bit|E-bit|R-bit) Type = 2 ;connects to N3 Metric = 1 ;cost to N3 Interface ID = 1 ;RT3's Interface ID on N3 Neighbor Interface ID = 1 ;RT4's Interface ID on N3 Neighbor Router ID = 192.0.2.4 ; RT4's Router ID RT3's router-LSA for Area 1 For example, if another router was added to Network N4, RT3 would have to advertise a second link description for its connection to (the now transit) network N4. This could be accomplished by reoriginating the above router-LSA, this time with two link descriptions. Or, a separate router-LSA could be originated with a separate Link State ID (e.g., using a Link State ID of 1) to describe the connection to N4. Host routes for stub networks no longer appear in the router-LSA. Rather, they are included in intra-area-prefix-LSAs. 4.4.3.3. Network-LSAs The LS type of a network-LSA is set to the value 0x2002. Network- LSAs have area flooding scope. A network-LSA is originated for every broadcast or NBMA link with an elected Designated Router that is fully adjacent with at least one other router on the link. The network-LSA is originated by the link's Designated Router and lists all routers on the link with which it is fully adjacent. The procedure for originating network-LSAs in IPv6 is the same as the IPv4 procedure documented in Section 12.4.2 of [OSPFV2], with the following exceptions: o An IPv6 network-LSA's Link State ID is set to the Interface ID of the Designated Router on the link. o IPv6 network-LSAs do not contain a Network Mask. All addressing information formerly contained in the IPv4 network-LSA has now been consigned to intra-Area-Prefix-LSAs originated by the link's Designated Router. Coltun, et al. Standards Track [Page 29]
RFC 5340 OSPF for IPv6 July 2008 o The Options field in the network-LSA is set to the logical OR of the Options fields contained within the link's associated link- LSAs corresponding to fully adjacent neighbors. In this way, the network link exhibits a capability when at least one fully adjacent neighbor on the link requests that the capability be advertised. As an example, assuming that Router RT4 has been elected the Designated Router of Network N3 in Figure 1, the following network- LSA is originated: ; Network-LSA for Network N3 LS age = 0 ;newly (re)originated LS type = 0x2002 ;network-LSA Link State ID = 1 ;RT4's Interface ID on N3 Advertising Router = 192.0.2.4 ;RT4's Router ID Options = (V6-bit|E-bit|R-bit) Attached Router = 192.0.2.4 ;Router ID Attached Router = 192.0.2.1 ;Router ID Attached Router = 192.0.2.2 ;Router ID Attached Router = 192.0.2.3 ;Router ID Network-LSA for Network N3 4.4.3.4. Inter-Area-Prefix-LSAs The LS type of an inter-area-prefix-LSA is set to the value 0x2003. Inter-area-prefix-LSAs have area flooding scope. In IPv4, inter- area-prefix-LSAs were called type 3 summary-LSAs. Each inter-area- prefix-LSA describes a prefix external to the area, yet internal to the Autonomous System. The procedure for originating inter-area-prefix-LSAs in IPv6 is the same as the IPv4 procedure documented in Sections 12.4.3 and 12.4.3.1 of [OSPFV2], with the following exceptions: o The Link State ID of an inter-area-prefix-LSA has lost all of its addressing semantics and simply serves to distinguish multiple inter-area-prefix-LSAs that are originated by the same router. o The prefix is described by the PrefixLength, PrefixOptions, and Address Prefix fields embedded within the LSA body. Network Mask is no longer specified. o The NU-bit in the PrefixOptions field should be clear. Coltun, et al. Standards Track [Page 30]
RFC 5340 OSPF for IPv6 July 2008 o Link-local addresses MUST never be advertised in inter-area- prefix-LSAs. As an example, the following shows the inter-area-prefix-LSA that Router RT4 originates into the OSPF backbone area, condensing all of Area 1's prefixes into the single prefix 2001:0db8:c001::/48. The cost is set to 4, which is the maximum cost of all of the individual component prefixes. The prefix is padded out to an even number of 32-bit words, so that it consumes 64 bits of space instead of 48 bits. ; Inter-area-prefix-LSA for Area 1 addresses ; originated by Router RT4 into the backbone LS age = 0 ;newly (re)originated LS type = 0x2003 ;inter-area-prefix-LSA Advertising Router = 192.0.2.4 ;RT4's ID Metric = 4 ;maximum to components PrefixLength = 48 PrefixOptions = 0 Address Prefix = 2001:0db8:c001 ;padded to 64-bits Inter-area-prefix-LSA for Area 1 addresses originated by Router RT4 into the backbone 4.4.3.5. Inter-Area-Router-LSAs The LS type of an inter-area-router-LSA is set to the value 0x2004. Inter-area-router-LSAs have area flooding scope. In IPv4, inter- area-router-LSAs were called type 4 summary-LSAs. Each inter-area- router-LSA describes a path to a destination OSPF router (i.e., an AS Boundary Router (ASBR)) that is external to the area yet internal to the Autonomous System. The procedure for originating inter-area-router-LSAs in IPv6 is the same as the IPv4 procedure documented in Section 12.4.3 of [OSPFV2], with the following exceptions: o The Link State ID of an inter-area-router-LSA is no longer the destination router's OSPF Router ID and now simply serves to distinguish multiple inter-area-router-LSAs that are originated by the same router. The destination router's Router ID is now found in the body of the LSA. Coltun, et al. Standards Track [Page 31]
RFC 5340 OSPF for IPv6 July 2008 o The Options field in an inter-area-router-LSA should be set equal to the Options field contained in the destination router's own router-LSA. The Options field thus describes the capabilities supported by the destination router. As an example, consider the OSPF Autonomous System depicted in Figure 6 of [OSPFV2]. Router RT4 would originate into Area 1 the following inter-area-router-LSA for destination router RT7. ; inter-area-router-LSA for AS boundary router RT7 ; originated by Router RT4 into Area 1 LS age = 0 ;newly (re)originated LS type = 0x2004 ;inter-area-router-LSA Advertising Router = 192.0.2.4 ;RT4's ID Options = (V6-bit|E-bit|R-bit) ;RT7's capabilities Metric = 14 ;cost to RT7 Destination Router ID = Router RT7's ID Inter-area-router-LSA for AS boundary router RT7 originated by Router RT4 into Area 1 4.4.3.6. AS-External-LSAs The LS type of an AS-external-LSA is set to the value 0x4005. AS- external-LSAs have AS flooding scope. Each AS-external-LSA describes a path to a prefix external to the Autonomous System. The procedure for originating AS-external-LSAs in IPv6 is the same as the IPv4 procedure documented in Section 12.4.4 of [OSPFV2], with the following exceptions: o The Link State ID of an AS-external-LSA has lost all of its addressing semantics and simply serves to distinguish multiple AS- external-LSAs that are originated by the same router. o The prefix is described by the PrefixLength, PrefixOptions, and Address Prefix fields embedded within the LSA body. Network Mask is no longer specified. o The NU-bit in the PrefixOptions field should be clear. o Link-local addresses can never be advertised in AS-external-LSAs. o The forwarding address is present in the AS-external-LSA if and only if the AS-external-LSA's bit F is set. Coltun, et al. Standards Track [Page 32]
RFC 5340 OSPF for IPv6 July 2008 o The external route tag is present in the AS-external-LSA if and only if the AS-external-LSA's bit T is set. o The capability for an AS-external-LSA to reference another LSA has been supported through the inclusion of the Referenced LS Type field and the optional Referenced Link State ID field (the latter present if and only if the Referenced LS Type is non-zero). This capability is for future use; the Referenced LS Type should be set to 0, and received non-zero values for this field should be ignored until its use is defined. As an example, consider the OSPF Autonomous System depicted in Figure 6 of [OSPFV2]. Assume that RT7 has learned its route to N12 via BGP and that it wishes to advertise a Type 2 metric into the AS. Also assume that the IPv6 prefix for N12 is the value 2001:0db8:0a00::/40. RT7 would then originate the following AS-external-LSA for the external network N12. Note that within the AS-external-LSA, N12's prefix occupies 64 bits of space in order to maintain 32-bit alignment. ; AS-external-LSA for Network N12, ; originated by Router RT7 LS age = 0 ;newly (re)originated LS type = 0x4005 ;AS-external-LSA Link State ID = 123 ;LSA type/scope unique identifier Advertising Router = Router RT7's ID bit E = 1 ;Type 2 metric bit F = 0 ;no forwarding address bit T = 1 ;external route tag included Metric = 2 PrefixLength = 40 PrefixOptions = 0 Referenced LS Type = 0 ;no Referenced Link State ID Address Prefix = 2001:0db8:0a00 ;padded to 64-bits External Route Tag = as per BGP/OSPF interaction AS-external-LSA for Network N12, originated by Router RT7 4.4.3.7. NSSA-LSAs The LS type of an NSSA-LSA is set to the value 0x2007. NSSA-LSAs have area flooding scope. Each NSSA-LSA describes a path to a prefix external to the Autonomous System whose flooding scope is restricted to a single NSSA area. The procedure for originating NSSA-LSAs in IPv6 is the same as the IPv4 procedure documented in [NSSA], with the following exceptions: Coltun, et al. Standards Track [Page 33]
RFC 5340 OSPF for IPv6 July 2008 o The Link State ID of an NSSA-LSA has lost all of its addressing semantics and simply serves to distinguish multiple NSSA-LSAs that are originated by the same router in the same area. o The prefix is described by the PrefixLength, PrefixOptions, and Address Prefix fields embedded within the LSA body. Network Mask is no longer specified. o The NU-bit in the PrefixOptions field should be clear. o Link-local addresses can never be advertised in NSSA-LSAs. o The forwarding address is present in the NSSA-LSA if and only if the NSSA-LSA's bit F is set. o The external route tag is present in the NSSA-LSA if and only if the NSSA-LSA's bit T is set. o The capability for an NSSA-LSA to reference another LSA has been supported through the inclusion of the Referenced LS Type field and the optional Referenced Link State ID field (the latter present if and only if the Referenced LS Type is non-zero). This capability is for future use; the Referenced LS Type should be set to 0, and received non-zero values for this field should be ignored until its use is defined. An example of an NSSA-LSA would only differ from an AS-external-LSA in that the LS type would be 0x2007 rather than 0x4005. 4.4.3.8. Link-LSAs The LS type of a link-LSA is set to the value 0x0008. Link-LSAs have link-local flooding scope. A router originates a separate link-LSA for each attached link that supports two or more (including the originating router itself) routers. Link-LSAs SHOULD NOT be originated for virtual links. Link-LSAs have three purposes: 1. They provide the router's link-local address to all other routers attached to the link. 2. They inform other routers attached to the link of a list of IPv6 prefixes to associate with the link. 3. They allow the router to advertise a collection of Options bits in the network-LSA originated by the Designated Router on a broadcast or NBMA link. Coltun, et al. Standards Track [Page 34]
RFC 5340 OSPF for IPv6 July 2008 A link-LSA for a given Link L is built in the following fashion: o The Link State ID is set to the router's Interface ID on Link L. o The Router Priority of the router's interface to Link L is inserted into the link-LSA. o The link-LSA's Options field is set to reflect the router's capabilities. On multi-access links, the Designated Router will logically OR the link-LSA Options fields for all fully adjacent neighbors in Link L's network-LSA. o The router inserts its link-local address on Link L into the link- LSA. This information will be used when the other routers on Link L do their next-hop calculations (see Section 4.8.2). o Each IPv6 address prefix that has been configured on Link L is added to the link-LSA by specifying values for the PrefixLength, PrefixOptions, and Address Prefix fields. After building a link-LSA for a given link, the router installs the link-LSA into the associated interface data structure and floods the link-LSA on the link. All other routers on the link will receive the link-LSA, but they will not flood the link-LSA on other links. If LinkLSASuppression is configured for the interface and the interface type is not broadcast or NBMA, origination of the link-LSA may be suppressed. This implies that other routers on the link will ascertain the router's next-hop address using a mechanism other than the link-LSA (see Section 4.8.2). Refer to Appendix C.3 for a description of the LinkLSASuppression interface configuration parameter. As an example, consider the link-LSA that RT3 will build for N3 in Figure 1. Suppose that the prefix 2001:0db8:c001:0100::/56 has been configured within RT3 for N3. This will result in the following link-LSA that RT3 will flood only on N3. Note that not all routers on N3 need be configured with the prefix; those not configured will learn the prefix when receiving RT3's link-LSA. Coltun, et al. Standards Track [Page 35]
RFC 5340 OSPF for IPv6 July 2008 ; RT3's link-LSA for N3 LS age = 0 ;newly (re)originated LS type = 0x0008 ;link-LSA Link State ID = 1 ;RT3's Interface ID on N3 Advertising Router = 192.0.2.3 ;RT3's Router ID Rtr Priority = 1 ;RT3's N3 Router Priority Options = (V6-bit|E-bit|R-bit) Link-local Interface Address = fe80:0001::RT3 # prefixes = 1 PrefixLength = 56 PrefixOptions = 0 Address Prefix = 2001:0db8:c001:0100 ;pad to 64-bits RT3's link-LSA for N3 4.4.3.9. Intra-Area-Prefix-LSAs The LS type of an intra-area-prefix-LSA is set to the value 0x2009. Intra-area-prefix-LSAs have area flooding scope. An intra-area- prefix-LSA has one of two functions. It either associates a list of IPv6 address prefixes with a transit network link by referencing a network-LSA, or associates a list of IPv6 address prefixes with a router by referencing a router-LSA. A stub link's prefixes are associated with its attached router. A router MAY originate multiple intra-area-prefix-LSAs for a given area. Each intra-area-prefix-LSA has a unique Link State ID and contains an integral number of prefix descriptions. A link's Designated Router originates one or more intra-area-prefix- LSAs to advertise the link's prefixes throughout the area. For a link L, L's Designated Router builds an intra-area-prefix-LSA in the following fashion: o In order to indicate that the prefixes are to be associated with the Link L, the fields Referenced LS Type, Referenced Link State ID, and Referenced Advertising Router are set to the corresponding fields in Link L's network-LSA (namely, LS type, Link State ID, and Advertising Router respectively). This means that the Referenced LS Type is set to 0x2002, the Referenced Link State ID is set to the Designated Router's Interface ID on Link L, and the Referenced Advertising Router is set to the Designated Router's Router ID. o Each link-LSA associated with Link L is examined (these are in the Designated Router's interface structure for Link L). If the link- LSA's Advertising Router is fully adjacent to the Designated Coltun, et al. Standards Track [Page 36]
RFC 5340 OSPF for IPv6 July 2008 Router and the Link State ID matches the neighbor's interface ID, the list of prefixes in the link-LSA is copied into the intra- area-prefix-LSA that is being built. Prefixes having the NU-bit and/or LA-bit set in their Options field SHOULD NOT be copied, nor should link-local addresses be copied. Each prefix is described by the PrefixLength, PrefixOptions, and Address Prefix fields. Multiple prefixes having the same PrefixLength and Address Prefix are considered to be duplicates. In this case, their PrefixOptions fields should be logically OR'ed together, and a single instance of the duplicate prefix should be included in the intra-area-prefix-LSA. The Metric field for all prefixes is set to 0. o The "# prefixes" field is set to the number of prefixes that the router has copied into the LSA. If necessary, the list of prefixes can be spread across multiple intra-area-prefix-LSAs in order to keep the LSA size small. A router builds an intra-area-prefix-LSA to advertise prefixes for its attached stub links, looped-back interfaces, and hosts. A Router RTX would build its intra-area-prefix-LSA in the following fashion: o In order to indicate that the prefixes are to be associated with the Router RTX itself, RTX sets the Referenced LS Type to 0x2001, the Referenced Link State ID to 0, and the Referenced Advertising Router to RTX's own Router ID. o Router RTX examines its list of interfaces to the area. If the interface is in the state Down, its prefixes are not included. If the interface has been reported in RTX's router-LSA as a Type 2 link description (link to transit network), prefixes that will be included in the intra-area-prefix-LSA for the link are skipped. However, any prefixes that would normally have the LA-bit set SHOULD be advertised independent of whether or not the interface is advertised as a transit link. If the interface type is point- to-multipoint or the interface is in the state Loopback, the global scope IPv6 addresses associated with the interface (if any) are copied into the intra-area-prefix-LSA with the PrefixOptions LA-bit set, the PrefixLength set to 128, and the metric set to 0. Otherwise, the list of global prefixes configured in RTX for the link are copied into the intra-area-prefix-LSA by specifying the PrefixLength, PrefixOptions, and Address Prefix fields. The Metric field for each of these prefixes is set to the interface's output cost. o RTX adds the IPv6 prefixes for any directly attached hosts belonging to the area (see Appendix C.7) to the intra-area-prefix- LSA. Coltun, et al. Standards Track [Page 37]
RFC 5340 OSPF for IPv6 July 2008 o If RTX has one or more virtual links configured through the area, it includes one of its global scope IPv6 interface addresses in the LSA (if it hasn't already), setting the LA-bit in the PrefixOptions field, the PrefixLength to 128, and the Metric to 0. This information will be used later in the routing calculation so that the two ends of the virtual link can discover each other's IPv6 addresses. o The "# prefixes" field is set to the number of prefixes that the router has copied into the LSA. If necessary, the list of prefixes can be spread across multiple intra-area-prefix-LSAs in order to keep the LSA size small. For example, the intra-area-prefix-LSA originated by RT4 for Network N3 (assuming that RT4 is N3's Designated Router) and the intra-area- prefix-LSA originated into Area 1 by Router RT3 for its own prefixes are pictured below. Coltun, et al. Standards Track [Page 38]
RFC 5340 OSPF for IPv6 July 2008 ; RT4's Intra-area-prefix-LSA for network link N3 LS age = 0 ;newly (re)originated LS type = 0x2009 ;Intra-area-prefix-LSA Link State ID = 5 ;LSA type/scope unique identifier Advertising Router = 192.0.2.4 ;RT4's Router ID # prefixes = 1 Referenced LS Type = 0x2002 ;network-LSA reference Referenced Link State ID = 1 Referenced Advertising Router = 192.0.2.4 PrefixLength = 56 ;N3's prefix PrefixOptions = 0 Metric = 0 Address Prefix = 2001:0db8:c001:0100 ;pad ; RT3's Intra-area-prefix-LSA for its own prefixes LS age = 0 ;newly (re)originated LS type = 0x2009 ;Intra-area-prefix-LSA Link State ID = 177 ;LSA type/scope unique identifier Advertising Router = 192.0.2.3 ;RT3's Router ID # prefixes = 1 Referenced LS Type = 0x2001 ;router-LSA reference Referenced Link State ID = 0 Referenced Advertising Router = 192.0.2.3 PrefixLength = 56 ;N4's prefix PrefixOptions = 0 Metric = 2 ;N4 interface cost Address Prefix = 2001:0db8:c001:0400 ;pad Intra-area-prefix-LSA for Network Link N3 When network conditions change, it may be necessary for a router to move prefixes from one intra-area-prefix-LSA to another. For example, if the router is the Designated Router for a link but the link has no other attached routers, the link's prefixes are advertised in an intra-area-prefix-LSA referring to the Designated Router's router-LSA. When additional routers appear on the link, a network-LSA is originated for the link and the link's prefixes are moved to an intra-area-prefix-LSA referring to the network-LSA. Note that in the intra-area-prefix-LSA, the Referenced Advertising Router is always equal to the router that is originating the intra- area-prefix-LSA (i.e., the LSA's Advertising Router). The reason the Referenced Advertising Router field appears is that, even though it is currently redundant, it may not be in the future. We may sometime want to use the same LSA format to advertise address prefixes for other protocol suites. In this case, the Designated Router may not Coltun, et al. Standards Track [Page 39]
RFC 5340 OSPF for IPv6 July 2008 be running the other protocol suite, and so another of the link's routers may need to originate the intra-area-prefix-LSA. In that case, the Referenced Advertising Router and Advertising Router would be different. 4.4.4. Future LSA Validation It is expected that new LSAs will be defined that will not be processed during the Shortest Path First (SPF) calculation as described in Section 4.8, for example, OSPFv3 LSAs corresponding to information advertised in OSPFv2 using opaque LSAs [OPAQUE]. In general, the new information advertised in future LSAs should not be used unless the OSPFv3 router originating the LSA is reachable. However, depending on the application and the data advertised, this reachability validation MAY be done less frequently than every SPF calculation. To facilitate inter-area reachability validation, any OSPFv3 router originating AS scoped LSAs is considered an AS Boundary Router (ASBR). 4.5. Flooding Most of the flooding algorithm remains unchanged from the IPv4 flooding mechanisms described in Section 13 of [OSPFV2]. In particular, the protocol processes for determining which LSA instance is newer (Section 13.1 of [OSPFV2]), responding to updates of self- originated LSAs (Section 13.4 of [OSPFV2]), sending Link State Acknowledgment packets (Section 13.5 of [OSPFV2]), retransmitting LSAs (Section 13.6 of [OSPFV2]), and receiving Link State Acknowledgment packets (Section 13.7 of [OSPFV2]), are exactly the same for IPv6 and IPv4. However, the addition of flooding scope and unknown LSA type handling (see Appendix A.4.2.1) has caused some changes in the OSPF flooding algorithm: the reception of Link State Updates (Section 13 in [OSPFV2]) and the sending of Link State Updates (Section 13.3 of [OSPFV2]) must take into account the LSA's scope and U-bit setting. Also, installation of LSAs into the OSPF database (Section 13.2 of [OSPFV2]) causes different events in IPv6, due to the reorganization of LSA types and the IPv6 LSA contents. These changes are described in detail below. 4.5.1. Receiving Link State Update Packets The encoding of flooding scope in the LS type and the need to process unknown LS types cause modifications to the processing of received Link State Update packets. As in IPv4, each LSA in a received Link Coltun, et al. Standards Track [Page 40]
RFC 5340 OSPF for IPv6 July 2008 State Update packet is examined. In IPv4, eight steps are executed for each LSA, as described in Section 13 of [OSPFV2]. For IPv6, all the steps are the same, except that Steps 2 and 3 are modified as follows: (2) Examine the LSA's LS type. Discard the LSA and get the next one from the Link State Update packet if the interface area has been configured as a stub or NSSA area and the LS type indicates "AS flooding scope". This generalizes the IPv4 behavior where AS-external-LSAs and AS-scoped opaque LSAs [OPAQUE] are not flooded throughout stub or NSSA areas. (3) Else if the flooding scope in the LSA's LS type is set to "reserved", discard the LSA and get the next one from the Link State Update packet. Steps 5b (sending Link State Update packets) and 5d (installing LSAs in the link-state database) in Section 13 of [OSPFV2] are also somewhat different for IPv6, as described in Sections 4.5.2 and 4.5.3 below. 4.5.2. Sending Link State Update Packets The sending of Link State Update packets is described in Section 13.3 of [OSPFV2]. For IPv4 and IPv6, the steps for sending a Link State Update packet are the same (steps 1 through 5 of Section 13.3 in [OSPFV2]). However, the list of eligible interfaces on which to flood the LSA is different. For IPv6, the eligible interfaces are selected based on the following factors: o The LSA's flooding scope. o For LSAs with area or link-local flooding scope, the particular area or interface with which the LSA is associated. o Whether the LSA has a recognized LS type. o The setting of the U-bit in the LS type. If the U-bit is set to 0, unrecognized LS types are treated as having link-local scope. If set to 1, unrecognized LS types are stored and flooded as if they were recognized. Coltun, et al. Standards Track [Page 41]
RFC 5340 OSPF for IPv6 July 2008 Choosing the set of eligible interfaces then breaks into the following cases: Case 1 The LSA's LS type is recognized. In this case, the set of eligible interfaces is set depending on the flooding scope encoded in the LS type. If the flooding scope is "AS flooding scope", the eligible interfaces are all router interfaces excepting virtual links. In addition, AS-external-LSAs are not flooded on interfaces connecting to stub or NSSA areas. If the flooding scope is "area flooding scope", the eligible interfaces are those interfaces connecting to the LSA's associated area. If the flooding scope is "link-local flooding scope", then there is a single eligible interface, the one connecting to the LSA's associated link (which is also the interface on which the LSA was received in a Link State Update packet). Case 2 The LS type is unrecognized and the U-bit in the LS type is set to 0 (treat the LSA as if it had link-local flooding scope). In this case, there is a single eligible interface, namely, the interface on which the LSA was received. Case 3 The LS type is unrecognized, and the U-bit in the LS type is set to 1 (store and flood the LSA as if the type is understood). In this case, select the eligible interfaces based on the encoded flooding scope the same as in Case 1 above. A further decision must sometimes be made before adding an LSA to a given neighbor's link-state retransmission list (Step 1d in Section 13.3 of [OSPFV2]). If the LS type is recognized by the router but not by the neighbor (as can be determined by examining the Options field that the neighbor advertised in its Database Description packet) and the LSA's U-bit is set to 0, then the LSA should be added to the neighbor's link-state retransmission list if and only if that neighbor is the Designated Router or Backup Designated Router for the attached link. The LS types described in detail by this document, namely, router-LSAs (LS type 0x2001), network-LSAs (0x2002), inter- area-prefix-LSAs (0x2003), inter-area-router-LSAs (0x2004), NSSA-LSAs (0x2007), AS-external-LSAs (0x4005), link-LSAs (0x0008), and Intra- Area-Prefix-LSAs (0x2009), are assumed to be understood by all routers. However, all LS types MAY not be understood by all routers. For example, a new LSA type with its U-bit set to 0 MAY only be understood by a subset of routers. This new LS type should only be flooded to an OSPF neighbor that understands the LS type or when the neighbor is the Designated Router or Backup Designated Router for the attached link. Coltun, et al. Standards Track [Page 42]
RFC 5340 OSPF for IPv6 July 2008 The previous paragraph solves a problem for IPv4 OSPF extensions, which require that the Designated Router support the extension in order to have the new LSA types flooded across broadcast and NBMA networks. 4.5.3. Installing LSAs in the Database There are three separate places to store LSAs, depending on their flooding scope. LSAs with AS flooding scope are stored in the global OSPF data structure (see Section 4.1) as long as their LS type is known or their U-bit is 1. LSAs with area flooding scope are stored in the appropriate area data structure (see Section 4.1.1) as long as their LS type is known or their U-bit is 1. LSAs with link-local flooding scope, and those LSAs with unknown LS type and U-bit set to 0 (treat the LSA as if it had link-local flooding scope), are stored in the appropriate interface data structure. When storing the LSA into the link-state database, a check must be made to see whether the LSA's contents have changed. Changes in contents are indicated exactly as in Section 13.2 of [OSPFV2]. When an LSA's contents have been changed, the following parts of the routing table must be recalculated, based on the LSA's LS type: Router-LSAs, Network-LSAs, Intra-Area-Prefix-LSAs, and Link-LSAs The entire routing table is recalculated, starting with the shortest-path calculation for each area (see Section 4.8). Inter-Area-Prefix-LSAs and Inter-Area-Router-LSAs The best route to the destination described by the LSA must be recalculated (see Section 16.5 in [OSPFV2]). If this destination is an AS boundary router, it may also be necessary to re-examine all the AS-external-LSAs. AS-external-LSAs and NSSA-LSAs The best route to the destination described by the AS-external-LSA or NSSA-LSA must be recalculated (see Section 16.6 in [OSPFV2] and Section 2.0 in [NSSA]). As in IPv4, any old instance of the LSA must be removed from the database when the new LSA is installed. This old instance must also be removed from all neighbors' link-state retransmission lists. 4.6. Definition of Self-Originated LSAs In IPv6, the definition of a self-originated LSA has been simplified from the IPv4 definition appearing in Sections 13.4 and 14.1 of [OSPFV2]. For IPv6, self-originated LSAs are those LSAs whose Advertising Router is equal to the router's own Router ID. Coltun, et al. Standards Track [Page 43]
RFC 5340 OSPF for IPv6 July 2008 4.7. Virtual Links OSPF virtual links for IPv4 are described in Section 15 of [OSPFV2]. Virtual links are the same in IPv6, with the following exceptions: o LSAs having AS flooding scope are never flooded over virtual adjacencies, nor are LSAs with AS flooding scope summarized over virtual adjacencies during the database exchange process. This is a generalization of the IPv4 treatment of AS-external-LSAs. o The IPv6 interface address of a virtual link MUST be an IPv6 address having global scope, instead of the link-local addresses used by other interface types. This address is used as the IPv6 source for OSPF protocol packets sent over the virtual link. Hence, a link-LSA SHOULD NOT be originated for a virtual link since the virtual link has no link-local address or associated prefixes. o Likewise, the virtual neighbor's IPv6 address is an IPv6 address with global scope. To enable the discovery of a virtual neighbor's IPv6 address during the routing calculation, the neighbor advertises its virtual link's IPv6 interface address in an intra-area-prefix-LSA originated for the virtual link's transit area (see Section 4.4.3.9 and Section 4.8.1). o Like all other IPv6 OSPF interfaces, virtual links are assigned unique (within the router) Interface IDs. These are advertised in Hellos sent over the virtual link and in the router's router-LSAs. 4.8. Routing Table Calculation The IPv6 OSPF routing calculation proceeds along the same lines as the IPv4 OSPF routing calculation, following the five steps specified by Section 16 of [OSPFV2]. High-level differences between the IPv6 and IPv4 calculations include: o Prefix information has been removed from router-LSAs and network- LSAs and is now advertised in intra-area-prefix-LSAs. Whenever [OSPFV2] specifies that stub networks within router-LSAs be examined, IPv6 will instead examine prefixes within intra-area- prefix-LSAs. o Type 3 and 4 summary-LSAs have been renamed inter-area-prefix-LSAs and inter-area-router-LSAs respectively. Coltun, et al. Standards Track [Page 44]
RFC 5340 OSPF for IPv6 July 2008 o Addressing information is no longer encoded in Link State IDs and is now only found within the body of LSAs. o In IPv6, a router can originate multiple router-LSAs, distinguished by Link State ID, within a single area. These router-LSAs MUST be treated as a single aggregate by the area's shortest-path calculation (see Section 4.8.1). For each area, the shortest-path tree calculation creates routing table entries for the area's routers and transit links (see Section 4.8.1). These entries are then used when processing intra- area-prefix-LSAs, inter-area-prefix-LSAs, and inter-area-router-LSAs, as described in Section 4.8.3. Events generated as a result of routing table changes (Section 16.7 of [OSPFV2]) and the equal-cost multipath logic (Section 16.8 of [OSPFV2]) are identical for both IPv4 and IPv6. 4.8.1. Calculating the Shortest-Path Tree for an Area The IPv4 shortest-path calculation is contained in Section 16.1 of [OSPFV2]. The graph used by the shortest-path tree calculation is identical for both IPv4 and IPv6. The graph's vertices are routers and transit links, represented by router-LSAs and network-LSAs respectively. A router is identified by its OSPF Router ID, while a transit link is identified by its Designated Router's Interface ID and OSPF Router ID. Both routers and transit links have associated routing table entries within the area (see Section 4.3). Section 16.1 of [OSPFV2] splits up the shortest-path calculations into two stages. First, the Dijkstra calculation is performed, and then the stub links are added onto the tree as leaves. The IPv6 calculation maintains this split. The Dijkstra calculation for IPv6 is identical to that specified for IPv4, with the following exceptions (referencing the steps from the Dijkstra calculation as described in Section 16.1 of [OSPFV2]): o The Vertex ID for a router is the OSPF Router ID. The Vertex ID for a transit network is a combination of the Interface ID and OSPF Router ID of the network's Designated Router. o In Step 2, when a router Vertex V has just been added to the shortest-path tree, there may be multiple LSAs associated with the router. All router-LSAs with the Advertising Router set to V's OSPF Router ID MUST be processed as an aggregate, treating them as fragments of a single large router-LSA. The Options field and the Coltun, et al. Standards Track [Page 45]
RFC 5340 OSPF for IPv6 July 2008 router type bits (bits Nt, V, E, and B) should always be taken from the router-LSA with the smallest Link State ID. o Step 2a is not needed in IPv6, as there are no longer stub network links in router-LSAs. o In Step 2b, if W is a router and the router-LSA V6-bit or R-bit is not set in the LSA options, the transit link W is ignored and V's next link is examined. o In Step 2b, if W is a router, there may again be multiple LSAs associated with the router. All router-LSAs with the Advertising Router set to W's OSPF Router ID MUST be processed as an aggregate, treating them as fragments of a single large router- LSA. o In Step 4, there are now per-area routing table entries for each of an area's routers rather than just the area border routers. These entries subsume all the functionality of IPv4's area border router routing table entries, including the maintenance of virtual links. When the router added to the area routing table in this step is the other end of a virtual link, the virtual neighbor's IP address is set as follows: The collection of intra-area-prefix- LSAs originated by the virtual neighbor is examined, with the virtual neighbor's IP address being set to the first prefix encountered with the LA-bit set. o Routing table entries for transit networks, which are no longer associated with IP networks, are also calculated in Step 4 and added to the per-area routing table. The next stage of the shortest-path calculation proceeds similarly to the two steps of the second stage of Section 16.1 in [OSPFV2]. However, instead of examining the stub links within router-LSAs, the list of the area's intra-area-prefix-LSAs is examined. A prefix advertisement whose NU-bit is set SHOULD NOT be included in the routing calculation. The cost of any advertised prefix is the sum of the prefix's advertised metric plus the cost to the transit vertex (either router or transit network) identified by intra-area-prefix- LSA's Referenced LS Type, Referenced Link State ID, and Referenced Advertising Router fields. This latter cost is stored in the transit vertex's routing table entry for the area. This specification does not require that the above algorithm be used to calculate the intra-area shortest-path tree. However, if another algorithm or optimization is used, an identical shortest-path tree must be produced. It is also important that any alternate algorithm or optimization maintain the requirement that transit vertices must Coltun, et al. Standards Track [Page 46]
RFC 5340 OSPF for IPv6 July 2008 be bidirectional for inclusion in the tree. Alternate algorithms and optimizations are beyond the scope of this specification. 4.8.2. The Next-Hop Calculation In IPv6, the calculation of the next-hop's IPv6 address (which will be a link-local address) proceeds along the same lines as the IPv4 next-hop calculation (see Section 16.1.1 of [OSPFV2]). However, there are some differences. When calculating the next-hop IPv6 address for a router (call it Router X) that shares a link with the calculating router, the calculating router assigns the next-hop IPv6 address to be the link-local interface address contained in Router X's link-LSA (see Appendix A.4.9) for the link. This procedure is necessary for some link types, for example NBMA, where the two routers need not be neighbors and might not be exchanging OSPF Hello packets. For other link types, the next-hop address may be determined via the IPv6 source address in the neighbor's Hello packet. Additionally, when calculating routes for the area's intra-area- prefix-LSAs, the parent vertex can be either a router-LSA or network- LSA. This is in contrast to the second stage of the OSPFv2 intra- area SPF (Section 16.1 in [OSPFV2]) where the parent vertex is always a router-LSA. In the case where the intra-area-prefix-LSA's referenced LSA is a directly connected network-LSA, the prefixes are also considered to be directly connected. In this case, the next hop is solely the outgoing link and no IPv6 next-hop address is selected. 4.8.3. Calculating the Inter-Area Routes Calculation of inter-area routes for IPv6 proceeds along the same lines as the IPv4 calculation in Section 16.2 of [OSPFV2], with the following modifications: o The names of the Type 3 summary-LSAs and Type 4 summary-LSAs have been changed to inter-area-prefix-LSAs and inter-area-router-LSAs respectively. o The Link State ID of the above LSA types no longer encodes the network or router described by the LSA. Instead, an address prefix is contained in the body of an inter-area-prefix-LSA and an advertised AS boundary router's OSPF Router ID is carried in the body of an inter-area-router-LSA. o Prefixes having the NU-bit set in their PrefixOptions field should be ignored by the inter-area route calculation. Coltun, et al. Standards Track [Page 47]
RFC 5340 OSPF for IPv6 July 2008 When a single inter-area-prefix-LSA or inter-area-router-LSA has changed, the incremental calculations outlined in Section 16.5 of [OSPFV2] can be performed instead of recalculating the entire routing table. 4.8.4. Examining Transit Areas' Summary-LSAs Examination of transit areas' summary-LSAs in IPv6 proceeds along the same lines as the IPv4 calculation in Section 16.3 of [OSPFV2], modified in the same way as the IPv6 inter-area route calculation in Section 4.8.3. 4.8.5. Calculating AS External and NSSA Routes The IPv6 AS external route calculation proceeds along the same lines as the IPv4 calculation in Section 16.4 of [OSPFV2] and Section 2.5 of [NSSA], with the following exceptions: o The Link State ID of the AS-external-LSA and NSSA-LSA types no longer encodes the network described by the LSA. Instead, an address prefix is contained in the body of the LSA. o The default route in AS-external-LSAs or NSSA-LSAs is advertised by a zero-length prefix. o Instead of comparing the AS-external-LSA's or NSSA-LSA's Forwarding Address field to 0.0.0.0 to see whether a forwarding address has been used, the bit F in the respective LSA is examined. A forwarding address is in use if and only if bit F is set. o Prefixes having the NU-bit set in their PrefixOptions field should be ignored by the inter-area route calculation. o AS Boundary Router (ASBR) and forwarding address selection will proceed the same as if RFC1583Compatibility is disabled. Furthermore, RFC1583Compatibility is not an OSPF for IPv6 configuration parameter. Refer to Appendix C.1. When a single AS-external-LSA or NSSA-LSA has changed, the incremental calculations outlined in Section 16.6 of [OSPFV2] can be performed instead of recalculating the entire routing table. 4.9. Multiple Interfaces to a Single Link In OSPF for IPv6, a router may have multiple interfaces to a single link associated with the same OSPF instance and area. All interfaces Coltun, et al. Standards Track [Page 48]
RFC 5340 OSPF for IPv6 July 2008 will be used for the reception and transmission of data traffic while only a single interface sends and receives OSPF control traffic. In more detail: o Each of the multiple interfaces is assigned a different Interface ID. A router will automatically detect that multiple interfaces are attached to the same link when a Hello packet is received with one of the router's link-local addresses as the source address and an Interface ID other than the Interface ID of the receiving interface. o Each of the multiple interfaces MUST be configured with the same Interface Instance ID to be considered on the same link. If an interface has multiple Instance IDs, it will be grouped with other interfaces based on matching Instance IDs. Each Instance ID will be treated uniquely with respect to groupings of multiple interfaces on the same link. For example, if interface A is configured with Instance IDs 1 and 35, and interface B is configured with Instance ID 35, interface B may be the Active Interface for Instance ID 35 but interface A will be active for Instance ID 1. o The router will ignore OSPF packets other than Hello packets on all but one of the interfaces attached to the link. It will only send its OSPF control packets (including Hello packets) on a single interface. This interface is designated the Active Interface and other interfaces attached to the same link will be designated Standby Interfaces. The choice of the Active Interface is implementation dependent. For example, the interface with the highest Interface ID could be chosen. If the router is elected Designated Router, it will be the Active Interface's Interface ID that will be used as the network-LSA's Link State ID. o All of the interfaces to the link (Active and Standby) will appear in the router-LSA. In addition, a link-LSA will be generated for each of the interfaces. In this way, all interfaces will be included in OSPF's routing calculations. o Any link-local scope LSAs that are originated for a Standby Interface will be flooded over the Active Interface. If a Standby Interface goes down, then the link-local scope LSAs originated for the Standby Interfaces MUST be flushed on the Active Interface. o Prefixes on Standby Interfaces will be processed the same way as prefixes on the Active Interface. For example, if the router is the DR for the link, the Active Interface's prefixes are included Coltun, et al. Standards Track [Page 49]
RFC 5340 OSPF for IPv6 July 2008 in an intra-area-prefix-LSA which is associated with the Active Interface's network-LSA; prefixes from Standby Interfaces on the link will also be included in that intra-area-prefix LSA. Similarly, if the link is a stub link, then the prefixes for the Active and Standby Interfaces will all be included in the same intra-area-prefix-LSA that is associated with the router-LSA. o If the Active Interface fails, a new Active Interface will have to take over. The new Active Interface SHOULD form all new neighbor adjacencies with routers on the link. This failure can be detected when the router's other interfaces to the Active Interface's link cease to hear the router's Hellos or through internal mechanisms, e.g., monitoring the Active Interface's status. o If the network becomes partitioned with different local interfaces attaching to different network partitions, multiple interfaces will become Active Interfaces and function independently. o During the SPF calculation when a network-LSA for a network that is directly connected to the root vertex is being examined, all of the multiple interfaces to the link of adjacent router-LSAs must be used in the next-hop calculation. This can be accomplished during the back link check (see Section 16.1, Step 2 (B), in [OSPFV2]) by examining each link of the router-LSA and making a list of the links that point to the network-LSA. The Interface IDs for links in this list are then used to find the corresponding link-LSAs and the link-local addresses used as next hops when installing equal-cost paths in the routing table. o The interface state machine is modified to add the state Standby. See Section 4.9.1 for a description of the Standby state. 4.9.1. Standby Interface State In this state, the interface is one of multiple interfaces to a link and this interface is designated Standby and is not sending or receiving control packets. The interface will continue to receive the Hello packets sent by the Active Interface. The interface will maintain a timer, the Active Interface Timer, with the same interval as the RouterDeadInterval. This timer will be reset whenever an OSPF Hello packet is received from the Active Interface to the link. Two new events are added to the list of events that cause interface state changes: MultipleInterfacesToLink and ActiveInterfaceDead. The descriptions of these events are as follows: Coltun, et al. Standards Track [Page 50]
RFC 5340 OSPF for IPv6 July 2008 MultipleInterfacesToLink An interfaces on the router has received a Hello packet from another interface on the same router. One of the interfaces is designated as the Active Interface and the other interface is designated as a Standby Interface. The Standby Interface transitions to the Standby state. ActiveInterfaceDead There has been an indication that a Standby Interface is no longer on a link with an Active Interface. The firing of the Active Interface Timer is one indication of this event, as it indicates that the Standby Interface has not received an OSPF Hello packet from the Active Interface for the RouterDeadInterval. Other indications may come from internal notifications, such as the Active Interface being disabled through a configuration change. Any indication internal to the router, such that the router knows the Active Interface is no longer active on the link, can trigger the ActiveInterfaceDead event for a Standby Interface. Interface state machine additions include: State(s): Waiting, DR Other, Backup, or DR Event: MultipleInterfacesToLink New state: Standby Action: All interface variables are reset and interface timers disabled. Also, all neighbor connections associated with the interface are destroyed. This is done by generating the event KillNbr on all associated neighbors. The Active Interface Timer is started and the interface will listen for OSPF Hello packets from the link's Active Interface. State(s): Standby Event: ActiveInterfaceDead New state: Down Action: The Active Interface Timer is first disabled. Then the InterfaceUp event is invoked. Standby Interface State Machine Additions Coltun, et al. Standards Track [Page 51]
RFC 5340 OSPF for IPv6 July 2008 5. Security Considerations When running over IPv6, OSPFv3 relies on the IP Authentication Header (see [IPAUTH]) and the IP Encapsulating Security Payload (see [IPESP]) to ensure integrity and authentication/confidentiality of protocol packets. This is described in [OSPFV3-AUTH]. Most OSPFv3 implementations will be running on systems that support multiple protocols with their own independent security assumptions and domains. When IPsec is used to protect OSPFv3 packets, it is important for the implementation to check the IPsec Security Association (SA) and local SA database to ensure the OSPF packet originated from a source that is trusted for OSPFv3. This is required to eliminate the possibility that the packet was authenticated using an SA defined for another protocol running on the same system. The mechanisms in [OSPFV3-AUTH] do not provide protection against compromised, malfunctioning, or misconfigured routers. Such routers can, either accidentally or deliberately, cause malfunctions affecting the whole routing domain. The reader is encouraged to consult [GENERIC-THREATS] for a more comprehensive description of threats to routing protocols. 6. Manageability Considerations The Management Information Base (MIB) for OSPFv3 is defined in [OSPFV3-MIB]. 7. IANA Considerations Most OSPF for IPv6 IANA considerations are documented in [OSPF-IANA]. IANA has updated the reference for RFC 2740 to this document. Additionally, this document introduces the following IANA requirements that were not present in [OSPFV3]: o Reserves the options with the values 0x000040 and 0x000080 for migrated OSPFv2 options in the OSPFv3 Options registry defined in [OSPF-IANA]. For information on the OSPFv3 Options field, refer to Appendix A.2. o Adds the prefix option P-bit with value 0x08 to the OSPFv3 Prefix Options registry defined in [OSPF-IANA]. For information on OSPFv3 Prefix Options, refer to Appendix A.4.1.1. Coltun, et al. Standards Track [Page 52]
RFC 5340 OSPF for IPv6 July 2008 o Adds the prefix option DN-bit with value 0x10 to the OSPFv3 Prefix Options registry defined in [OSPF-IANA]. For information on OSPFv3 Prefix Options, refer to Appendix A.4.1.1. 7.1. MOSPF for OSPFv3 Deprecation IANA Considerations With the deprecation of MOSPF for OSPFv3, the following code points are available for reassignment. Refer to [OSPF-IANA] for information on the respective registries. This document: o Deprecates the MC-bit with value 0x000004 in the OSPFv3 Options registry. o Deprecates Group-membership-LSA with value 6 in OSPFv3 LSA Function Code registry. o Deprecates MC-bit with value 0x04 in the OSPFv3 Prefix Options registry. The W-bit in the OSPFv3 Router Properties has also been deprecated. This requires a new registry for OSPFv3 router properties since it will diverge from the OSPFv2 Router Properties. Registry Name: OSPFv3 Router Properties Registry Reference: RFC 5340 Registration Procedures: Standards Action Registry: Value Description Reference ------ ------------- --------- 0x01 B-bit RFC 5340 0x02 E-bit RFC 5340 0x04 V-bit RFC 5340 0x08 Deprecated RFC 5340 0x10 Nt-bit RFC 5340 OSPFv3 Router Properties Registry 8. Acknowledgments The RFC text was produced using Marshall Rose's xml2rfc tool. The following individuals contributed comments that were incorporated into this document: o Harold Rabbie for his description of protocol details that needed to be clarified for OSPFv3 NSSA support. Coltun, et al. Standards Track [Page 53]
RFC 5340 OSPF for IPv6 July 2008 o Nic Neate for his pointing out that there needed to be changes for unknown LSA types handling in the processing of Database Description packets. o Jacek Kwiatkowski for being the first to point out that the V6- and R-bits are not taken into account in the OSPFv3 intra-area SPF calculation. o Michael Barnes recognized that the support for multiple interfaces to a single link was broken (see Section 4.9) and provided the description of the current protocol mechanisms. Abhay Roy reviewed and suggested improvements to the mechanisms. o Alan Davey reviewed and commented on document revisions. o Vivek Dubey reviewed and commented on document revisions. o Manoj Goyal and Vivek Dubey complained enough about link-LSAs being unnecessary to compel introduction of the LinkLSASuppression interface configuration parameter. o Manoj Goyal for pointing out that the next-hop calculation for intra-area-prefix-LSAs corresponding to network vertices was unclear. o Ramana Koppula reviewed and commented on document revisions. o Paul Wells reviewed and commented on document revisions. o Amir Khan reviewed and commented on document revisions. o Dow Street and Wayne Wheeler commented on the addition of the DN- bit to OSPFv3. o Mitchell Erblichs provided numerous editorial comments. o Russ White provided numerous editorial comments. o Kashima Hiroaki provided editorial comments. o Sina Mirtorabi suggested that OSPFv3 should be aligned with OSPFv2 with respect to precedence and should map it to IPv6 traffic class as specified in RFC 2474. Steve Blake helped with the text. o Faraz Shamin reviewed a late version of the document and provided editorial comments. Coltun, et al. Standards Track [Page 54]
RFC 5340 OSPF for IPv6 July 2008 o Christian Vogt performed the General Area Review Team (Gen-ART) review and provided comments. o Dave Ward, Dan Romascanu, Tim Polk, Ron Bonica, Pasi Eronen, and Lars Eggert provided comments during the IESG review. Also, thanks to Pasi for the text in Section 5 relating to routing threats. 9. References 9.1. Normative References [DEMAND] Moy, J., "Extending OSPF to Support Demand Circuits", RFC 1793, April 1995. [DIFF-SERV] Nichols, K., Blake, S., Baker, F., and D. Black, "Definition of the Differentiated Services Field (DS Field) in the IPv4 and IPv6 Headers", RFC 2474, December 1998. [DN-BIT] Rosen, E., Peter, P., and P. Pillay-Esnault, "Using a Link State Advertisement (LSA) Options Bit to Prevent Looping in BGP/MPLS IP Virtual Private Networks (VPNs)", RFC 4576, June 2006. [INTFMIB] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB", RFC 2863, June 2000. [IP6ADDR] Hinden, R. and S. Deering, "IP Version 6 Addressing Architecture", RFC 4291, February 2006. [IPAUTH] Kent, S., "IP Authentication Header", RFC 4302, December 2005. [IPESP] Kent, S., "IP Encapsulating Security Payload (ESP)", RFC 4303, December 2005. [IPV4] Postal, J., "Internet Protocol", STD 5, RFC 791, September 1981. [IPV6] Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", RFC 2460, December 1998. [NSSA] Murphy, P., "The OSPF Not-So-Stubby Area (NSSA) Option", RFC 3101, January 2003. Coltun, et al. Standards Track [Page 55]
RFC 5340 OSPF for IPv6 July 2008 [OSPF-IANA] Kompella, K. and B. Fenner, "IANA Considerations for OSPF", BCP 130, RFC 4940, July 2007. [OSPFV2] Moy, J., "OSPF Version 2", STD 54, RFC 2328, April 1998. [OSPFV3-AUTH] Gupta, M. and N. Melam, "Authentication/ Confidentiality for OSPFv3", RFC 4552, June 2006. [RFC-KEYWORDS] Bradner, S., "Key words for use in RFCs to Indicate Requirement Levels", BCP 14, RFC 2119, March 1997. 9.2. Informative References [GENERIC-THREATS] Barbir, A., Murphy, S., and Y. Yang, "Generic Threats to Routing Protocols", RFC 4593, October 2006. [MOSPF] Moy, J., "Multicast Extensions to OSPF", RFC 1584, March 1994. [MTUDISC] Mogul, J. and S. Deering, "Path MTU discovery", RFC 1191, November 1990. [OPAQUE] Coltun, R., "The OSPF Opaque LSA Option", RFC 2370, July 1998. [OSPFV3] Coltun, R., Ferguson, D., and J. Moy, "OSPF for IPv6", RFC 2740, December 1999. [OSPFV3-MIB] Joyal, D. and V. Manral, "Management Information Base for OSPFv3", Work in Progress, September 2007. [SERV-CLASS] Babiarz, J., Chan, K., and F. Baker, "Configuration Guidelines for DiffServ Service Classes", RFC 4594, August 2006. Coltun, et al. Standards Track [Page 56]
RFC 5340 OSPF for IPv6 July 2008 Appendix A. OSPF Data Formats This appendix describes the format of OSPF protocol packets and OSPF LSAs. The OSPF protocol runs directly over the IPv6 network layer. Before any data formats are described, the details of the OSPF encapsulation are explained. Next, the OSPF Options field is described. This field describes various capabilities that may or may not be supported by pieces of the OSPF routing domain. The OSPF Options field is contained in OSPF Hello packets, Database Description packets, and OSPF LSAs. OSPF packet formats are detailed in Section A.3. A description of OSPF LSAs appears in Section A.4. This section describes how IPv6 address prefixes are represented within LSAs, details the standard LSA header, and then provides formats for each of the specific LSA types. A.1. Encapsulation of OSPF Packets OSPF runs directly over the IPv6's network layer. OSPF packets are therefore encapsulated solely by IPv6 and local data-link headers. OSPF does not define a way to fragment its protocol packets, and depends on IPv6 fragmentation when transmitting packets larger than the link MTU. If necessary, the length of OSPF packets can be up to 65,535 bytes. The OSPF packet types that are likely to be large (Database Description, Link State Request, Link State Update, and Link State Acknowledgment packets) can usually be split into multiple protocol packets without loss of functionality. This is recommended; IPv6 fragmentation should be avoided whenever possible. Using this reasoning, an attempt should be made to limit the size of OSPF packets sent over virtual links to 1280 bytes unless Path MTU Discovery is being performed [MTUDISC]. The other important features of OSPF's IPv6 encapsulation are: o Use of IPv6 multicast. Some OSPF messages are multicast when sent over broadcast networks. Two distinct IP multicast addresses are used. Packets sent to these multicast addresses should never be forwarded; they are meant to travel a single hop only. As such, the multicast addresses have been chosen with link-local scope and packets sent to these addresses should have their IPv6 Hop Limit set to 1. b Coltun, et al. Standards Track [Page 57]
RFC 5340 OSPF for IPv6 July 2008 AllSPFRouters This multicast address has been assigned the value FF02::5. All routers running OSPF should be prepared to receive packets sent to this address. Hello packets are always sent to this destination. Also, certain OSPF protocol packets are sent to this address during the flooding procedure. AllDRouters This multicast address has been assigned the value FF02::6. Both the Designated Router and Backup Designated Router must be prepared to receive packets destined to this address. Certain OSPF protocol packets are sent to this address during the flooding procedure. o OSPF is IP protocol 89. This number SHOULD be inserted in the Next Header field of the encapsulating IPv6 header. o The OSPFv2 specification (Appendix A.1 in [OSPFV2]) indicates that OSPF protocol packets are sent with IP precedence set to Internetwork Control (B'110') [IPV4]. If routers in the OSPF routing domain map their IPv6 Traffic Class octet to the Differentiated Services Code Point (DSCP) as specified in [DIFF-SERV], then OSPFv3 packets SHOULD be sent with their DSCP set to CS6 (B'110000'), as specified in [SERV-CLASS]. In networks supporting this mapping, OSPF packets will be given precedence over IPv6 data traffic. A.2. The Options Field The 24-bit OSPF Options field is present in OSPF Hello packets, Database Description packets, and certain LSAs (router-LSAs, network- LSAs, inter-area-router-LSAs, and link-LSAs). The Options field enables OSPF routers to support (or not support) optional capabilities, and to communicate their capability level to other OSPF routers. Through this mechanism, routers of differing capabilities can be mixed within an OSPF routing domain. An option mismatch between routers can cause a variety of behaviors, depending on the particular option. Some option mismatches prevent neighbor relationships from forming (e.g., the E-bit below); these mismatches are discovered through the sending and receiving of Hello packets. Some option mismatches prevent particular LSA types from being flooded across adjacencies; these are discovered through the sending and receiving of Database Description packets. Some option mismatches prevent routers from being included in one or more of the various routing calculations because of their reduced functionality; these mismatches are discovered by examining LSAs. Coltun, et al. Standards Track [Page 58]
RFC 5340 OSPF for IPv6 July 2008 Seven bits of the OSPF Options field have been assigned. Each bit is described briefly below. Routers should reset (i.e., clear) unrecognized bits in the Options field when sending Hello packets or Database Description packets and when originating LSAs. Conversely, routers encountering unrecognized Options bits in received Hello packets, Database Description packets, or LSAs should ignore the unrecognized bits and process the packet or LSA normally. 1 2 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--+-+-+-+--+--+ | | | | | | | | | | | | | | | | |*|*|DC|R|N|x| E|V6| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--+-+-+-+--+--+ The Options field The Options field V6-bit If this bit is clear, the router/link should be excluded from IPv6 routing calculations. See Section 4.8 for details. E-bit This bit describes the way AS-external-LSAs are flooded, as described in Sections 3.6, 9.5, 10.8, and 12.1.2 of [OSPFV2]. x-Bit This bit was previously used by MOSPF (see [MOSPF]), which has been deprecated for OSPFv3. The bit should be set to 0 and ignored when received. It may be reassigned in the future. N-bit This bit indicates whether or not the router is attached to an NSSA as specified in [NSSA]. R-bit This bit (the `Router' bit) indicates whether the originator is an active router. If the router bit is clear, then routes that transit the advertising node cannot be computed. Clearing the router bit would be appropriate for a multi-homed host that wants to participate in routing, but does not want to forward non- locally addressed packets. DC-bit This bit describes the router's handling of demand circuits, as specified in [DEMAND]. Coltun, et al. Standards Track [Page 59]
RFC 5340 OSPF for IPv6 July 2008 *-bit These bits are reserved for migration of OSPFv2 protocol extensions. A.3. OSPF Packet Formats There are five distinct OSPF packet types. All OSPF packet types begin with a standard 16-byte header. This header is described first. Each packet type is then described in a succeeding section. In these sections, each packet's format is displayed and the packet's component fields are defined. All OSPF packet types (other than the OSPF Hello packets) deal with lists of LSAs. For example, Link State Update packets implement the flooding of LSAs throughout the OSPF routing domain. The format of LSAs is described in Section A.4. The receive processing of OSPF packets is detailed in Section 4.2.2. The sending of OSPF packets is explained in Section 4.2.1. A.3.1. The OSPF Packet Header Every OSPF packet starts with a standard 16-byte header. Together with the encapsulating IPv6 headers, the OSPF header contains all the information necessary to determine whether the packet should be accepted for further processing. This determination is described in Section 4.2.2. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Version # | Type | Packet length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Area ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Checksum | Instance ID | 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The OSPF Packet Header Version # The OSPF version number. This specification documents version 3 of the OSPF protocol. Coltun, et al. Standards Track [Page 60]
RFC 5340 OSPF for IPv6 July 2008 Type The OSPF packet types are as follows. See Appendix A.3.2 through Appendix A.3.6 for details. Type Description --------------------------------- 1 Hello 2 Database Description 3 Link State Request 4 Link State Update 5 Link State Acknowledgment Packet length The length of the OSPF protocol packet in bytes. This length includes the standard OSPF header. Router ID The Router ID of the packet's source. Area ID A 32-bit number identifying the area to which this packet belongs. All OSPF packets are associated with a single area. Most travel a single hop only. Packets traversing a virtual link are labeled with the backbone Area ID of 0. Checksum OSPF uses the standard checksum calculation for IPv6 applications: The 16-bit one's complement of the one's complement sum of the entire contents of the packet, starting with the OSPF packet header, and prepending a "pseudo-header" of IPv6 header fields, as specified in Section 8.1 of [IPV6]. The "Upper-Layer Packet Length" in the pseudo-header is set to the value of the OSPF packet header's length field. The Next Header value used in the pseudo-header is 89. If the packet's length is not an integral number of 16-bit words, the packet is padded with a byte of zero before checksumming. Before computing the checksum, the checksum field in the OSPF packet header is set to 0. Instance ID Enables multiple instances of OSPF to be run over a single link. Each protocol instance would be assigned a separate Instance ID; the Instance ID has link-local significance only. Received packets whose Instance ID is not equal to the receiving interface's Instance ID are discarded. Coltun, et al. Standards Track [Page 61]
RFC 5340 OSPF for IPv6 July 2008 0 These fields are reserved. They SHOULD be set to 0 when sending protocol packets and MUST be ignored when receiving protocol packets. A.3.2. The Hello Packet Hello packets are OSPF packet type 1. These packets are sent periodically on all interfaces (including virtual links) in order to establish and maintain neighbor relationships. In addition, Hello packets are multicast on those links having a multicast or broadcast capability, enabling dynamic discovery of neighboring routers. All routers connected to a common link must agree on certain parameters (HelloInterval and RouterDeadInterval). These parameters are included in Hello packets allowing differences to inhibit the forming of neighbor relationships. The Hello packet also contains fields used in Designated Router election (Designated Router ID and Backup Designated Router ID), and fields used to detect bidirectional communication (the Router IDs of all neighbors whose Hellos have been recently received). 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 3 | 1 | Packet Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Area ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Checksum | Instance ID | 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Interface ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Rtr Priority | Options | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | HelloInterval | RouterDeadInterval | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Designated Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Backup Designated Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Neighbor ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | The OSPF Hello Packet Coltun, et al. Standards Track [Page 62]
RFC 5340 OSPF for IPv6 July 2008 Interface ID 32-bit number uniquely identifying this interface among the collection of this router's interfaces. For example, in some implementations it may be possible to use the MIB-II IfIndex ([INTFMIB]). Rtr Priority This router's Router Priority. Used in (Backup) Designated Router election. If set to 0, the router will be ineligible to become (Backup) Designated Router. Options The optional capabilities supported by the router, as documented in Section A.2. HelloInterval The number of seconds between this router's Hello packets. RouterDeadInterval The number of seconds before declaring a silent router down. Designated Router ID The sending router's view of the identity of the Designated Router for this network. The Designated Router is identified by its Router ID. It is set to 0.0.0.0 if there is no Designated Router. Backup Designated Router ID The sending router's view of the identity of the Backup Designated Router for this network. The Backup Designated Router is identified by its IP Router ID. It is set to 0.0.0.0 if there is no Backup Designated Router. Neighbor ID The Router IDs of each router on the network with neighbor state 1-Way or greater. A.3.3. The Database Description Packet Database Description packets are OSPF packet type 2. These packets are exchanged when an adjacency is being initialized. They describe the contents of the link-state database. Multiple packets may be used to describe the database. For this purpose, a poll-response procedure is used. One of the routers is designated to be the master and the other is the slave. The master sends Database Description packets (polls) that are acknowledged by Database Description packets sent by the slave (responses). The responses are linked to the polls via the packets' DD sequence numbers. Coltun, et al. Standards Track [Page 63]
RFC 5340 OSPF for IPv6 July 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--+ | 3 | 2 | Packet Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--+ | Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--+ | Area ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--+ | Checksum | Instance ID | 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--+ | 0 | Options | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--+ | Interface MTU | 0 |0|0|0|0|0|I|M|MS| +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--+ | DD sequence number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--+ | | +- -+ | | +- An LSA Header -+ | | +- -+ | | +- -+ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+--+ | ... | The OSPF Database Description Packet The format of the Database Description packet is very similar to both the Link State Request packet and the Link State Acknowledgment packet. The main part of all three is a list of items, each item describing a piece of the link-state database. The sending of Database Description packets is documented in Section 10.8 of [OSPFV2]. The reception of Database Description packets is documented in Section 10.6 of [OSPFV2]. Options The optional capabilities supported by the router, as documented in Section A.2. Interface MTU The size in bytes of the largest IPv6 datagram that can be sent out the associated interface without fragmentation. The MTUs of common Internet link types can be found in Table 7-1 of [MTUDISC]. Coltun, et al. Standards Track [Page 64]
RFC 5340 OSPF for IPv6 July 2008 Interface MTU should be set to 0 in Database Description packets sent over virtual links. I-bit The Init bit. When set to 1, this packet is the first in the sequence of Database Description packets. M-bit The More bit. When set to 1, it indicates that more Database Description packets are to follow. MS-bit The Master/Slave bit. When set to 1, it indicates that the router is the master during the Database Exchange process. Otherwise, the router is the slave. DD sequence number Used to sequence the collection of Database Description packets. The initial value (indicated by the Init bit being set) should be unique. The DD sequence number then increments until the complete database for both the master and slave routers have been exchanged. The rest of the packet consists of a (possibly partial) list of the link-state database's pieces. Each LSA in the database is described by its LSA header. The LSA header is documented in Appendix A.4.2. It contains all the information required to uniquely identify both the LSA and the LSA's current instance. A.3.4. The Link State Request Packet Link State Request packets are OSPF packet type 3. After exchanging Database Description packets with a neighboring router, a router may find that parts of its link-state database are out-of-date. The Link State Request packet is used to request the pieces of the neighbor's database that are more up-to-date. Multiple Link State Request packets may need to be used. A router that sends a Link State Request packet has in mind the precise instance of the database pieces it is requesting. Each instance is defined by its LS sequence number, LS checksum, and LS age, although these fields are not specified in the Link State Request packet itself. The router may receive even more recent LSA instances in response. The sending of Link State Request packets is documented in Section 10.9 of [OSPFV2]. The reception of Link State Request packets is documented in Section 10.7 of [OSPFV2]. Coltun, et al. Standards Track [Page 65]
RFC 5340 OSPF for IPv6 July 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 3 | 3 | Packet Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Area ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Checksum | Instance ID | 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0 | LS Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | The OSPF Link State Request Packet Each LSA requested is specified by its LS type, Link State ID, and Advertising Router. This uniquely identifies the LSA without specifying its instance. Link State Request packets are understood to be requests for the most recent instance of the specified LSAs. A.3.5. The Link State Update Packet Link State Update packets are OSPF packet type 4. These packets implement the flooding of LSAs. Each Link State Update packet carries a collection of LSAs one hop further from their origin. Several LSAs may be included in a single packet. Link State Update packets are multicast on those physical networks that support multicast/broadcast. In order to make the flooding procedure reliable, flooded LSAs are acknowledged in Link State Acknowledgment packets. If retransmission of certain LSAs is necessary, the retransmitted LSAs are always carried by unicast Link State Update packets. For more information on the reliable flooding of LSAs, consult Section 4.5. Coltun, et al. Standards Track [Page 66]
RFC 5340 OSPF for IPv6 July 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 3 | 4 | Packet Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Area ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Checksum | Instance ID | 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | # LSAs | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | +- +-+ | LSAs | +- +-+ | ... | The OSPF Link State Update Packet # LSAs The number of LSAs included in this update. The body of the Link State Update packet consists of a list of LSAs. Each LSA begins with a common 20-byte header, described in Appendix A.4.2. Detailed formats of the different types of LSAs are described Appendix A.4. A.3.6. The Link State Acknowledgment Packet Link State Acknowledgment packets are OSPF packet type 5. To make the flooding of LSAs reliable, flooded LSAs are explicitly or implicitly acknowledged. Explicit acknowledgment is accomplished through the sending and receiving of Link State Acknowledgment packets. The sending of Link State Acknowledgment packets is documented in Section 13.5 of [OSPFV2]. The reception of Link State Acknowledgment packets is documented in Section 13.7 of [OSPFV2]. Multiple LSAs MAY be acknowledged in a single Link State Acknowledgment packet. Depending on the state of the sending interface and the sender of the corresponding Link State Update packet, a Link State Acknowledgment packet is sent to the multicast address AllSPFRouters, the multicast address AllDRouters, or to a neighbor's unicast address (see Section 13.5 of [OSPFV2] for details). Coltun, et al. Standards Track [Page 67]
RFC 5340 OSPF for IPv6 July 2008 The format of this packet is similar to that of the Data Description packet. The body of both packets is simply a list of LSA headers. 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 3 | 5 | Packet Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Area ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Checksum | Instance ID | 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | +- -+ | | +- An LSA Header -+ | | +- -+ | | +- -+ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | The OSPF Link State Acknowledgment Packet Each acknowledged LSA is described by its LSA header. The LSA header is documented in Appendix A.4.2. It contains all the information required to uniquely identify both the LSA and the LSA's current instance. A.4. LSA Formats This document defines eight distinct types of LSAs. Each LSA begins with a standard 20-byte LSA header. This header is explained in Appendix A.4.2. Succeeding sections describe each LSA type individually. Each LSA describes a piece of the OSPF routing domain. Every router originates a router-LSA. A network-LSA is advertised for each link by its Designated Router. A router's link-local addresses are advertised to its neighbors in link-LSAs. IPv6 prefixes are advertised in intra-area-prefix-LSAs, inter-area-prefix-LSAs, AS- external-LSAs, and NSSA-LSAs. Location of specific routers can be advertised across area boundaries in inter-area-router-LSAs. All LSAs are then flooded throughout the OSPF routing domain. The Coltun, et al. Standards Track [Page 68]
RFC 5340 OSPF for IPv6 July 2008 flooding algorithm is reliable, ensuring that all routers common to a flooding scope have the same collection of LSAs associated with that flooding scope. (See Section 4.5 for more information concerning the flooding algorithm.) This collection of LSAs is called the link- state database. From the link-state database, each router constructs a shortest-path tree with itself as root. This yields a routing table (see Section 11 of [OSPFV2]). For details on the routing table build process, see Section 4.8. A.4.1. IPv6 Prefix Representation IPv6 addresses are bit strings of length 128. IPv6 routing protocols, and OSPF for IPv6 in particular, advertise IPv6 address prefixes. IPv6 address prefixes are bit strings whose length ranges between 0 and 128 bits (inclusive). Within OSPF, IPv6 address prefixes are always represented by a combination of three fields: PrefixLength, PrefixOptions, and Address Prefix. PrefixLength is the length in bits of the prefix. PrefixOptions is an 8-bit field describing various capabilities associated with the prefix (see Appendix A.4.1.1). Address Prefix is an encoding of the prefix itself as an even multiple of 32-bit words, padding with zero bits as necessary. This encoding consumes ((PrefixLength + 31) / 32) 32-bit words. The default route is represented by a prefix of length 0. Examples of IPv6 Prefix representation in OSPF can be found in Appendix A.4.5, Appendix A.4.7, Appendix A.4.8, Appendix A.4.9, and Appendix A.4.10. A.4.1.1. Prefix Options Each prefix is advertised along with an 8-bit field of capabilities. These serve as input to the various routing calculations. For example, they can indicate that prefixes are to be ignored in some cases or are to be marked as not readvertisable in others. 0 1 2 3 4 5 6 7 +--+--+--+--+--+-+--+--+ | | | |DN| P|x|LA|NU| +--+--+--+--+--+-+--+--+ The PrefixOptions Field Coltun, et al. Standards Track [Page 69]
RFC 5340 OSPF for IPv6 July 2008 NU-bit The "no unicast" capability bit. If set, the prefix should be excluded from IPv6 unicast calculations. If not set, it should be included. LA-bit The "local address" capability bit. If set, the prefix is actually an IPv6 interface address of the Advertising Router. Advertisement of local interface addresses is described in Section 4.4.3.9. An implementation MAY also set the LA-bit for prefixes advertised with a host PrefixLength (128). x-bit This bit was previously defined as a "multicast" capability bit. However, the use was never adequately specified and has been deprecated for OSPFv3. The bit should be set to 0 and ignored when received. It may be reassigned in the future. P-bit The "propagate" bit. Set on NSSA area prefixes that should be readvertised by the translating NSSA area border [NSSA]. DN-bit This bit controls an inter-area-prefix-LSAs or AS-external-LSAs re-advertisement in a VPN environment as specified in [DN-BIT]. A.4.2. The LSA Header All LSAs begin with a common 20-byte header. This header contains enough information to uniquely identify the LSA (LS type, Link State ID, and Advertising Router). Multiple instances of the LSA may exist in the routing domain at the same time. It is then necessary to determine which instance is more recent. This is accomplished by examining the LS age, LS sequence number, and LS checksum fields that are also contained in the LSA header. Coltun, et al. Standards Track [Page 70]
RFC 5340 OSPF for IPv6 July 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Age | LS Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Checksum | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The LSA Header LS Age The time in seconds since the LSA was originated. LS Type The LS type field indicates the function performed by the LSA. The high-order three bits of LS type encode generic properties of the LSA, while the remainder (called LSA function code) indicate the LSA's specific functionality. See Appendix A.4.2.1 for a detailed description of LS type. Link State ID The originating router's identifier for the LSA. The combination of the Link State ID, LS type, and Advertising Router uniquely identify the LSA in the link-state database. Advertising Router The Router ID of the router that originated the LSA. For example, in network-LSAs this field is equal to the Router ID of the network's Designated Router. LS sequence number Successive instances of an LSA are given successive LS sequence numbers. The sequence number can be used to detect old or duplicate LSA instances. See Section 12.1.6 in [OSPFV2] for more details. LS checksum The Fletcher checksum of the complete contents of the LSA, including the LSA header but excluding the LS age field. See Section 12.1.7 in [OSPFV2] for more details. Coltun, et al. Standards Track [Page 71]
RFC 5340 OSPF for IPv6 July 2008 length The length in bytes of the LSA. This includes the 20-byte LSA header. A.4.2.1. LSA Type The LS type field indicates the function performed by the LSA. The high-order three bits of LS type encode generic properties of the LSA, while the remainder (called LSA function code) indicate the LSA's specific functionality. The format of the LS type is as follows: 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ |U |S2|S1| LSA Function Code | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ LSA Type The U-bit indicates how the LSA should be handled by a router that does not recognize the LSA's function code. Its values are: U-bit LSA Handling ------------------------------------------------------------- 0 Treat the LSA as if it had link-local flooding scope 1 Store and flood the LSA as if the type is understood U-Bit The S1 and S2 bits indicate the flooding scope of the LSA. The values are: S2 S1 Flooding Scope ------------------------------------------------------------- 0 0 Link-Local Scoping - Flooded only on originating link 0 1 Area Scoping - Flooded only in originating area 1 0 AS Scoping - Flooded throughout AS 1 1 Reserved Flooding Scope The LSA function codes are defined as follows. The origination and processing of these LSA function codes are defined elsewhere in this document, except for the NSSA-LSA (see [NSSA]) and 0x2006, which was previously used by MOSPF (see [MOSPF]). MOSPF has been deprecated for OSPFv3. As shown below, each LSA function b code also implies a specific setting for the U, S1, and S2 bits. Coltun, et al. Standards Track [Page 72]
RFC 5340 OSPF for IPv6 July 2008 LSA Function Code LS Type Description ---------------------------------------------------- 1 0x2001 Router-LSA 2 0x2002 Network-LSA 3 0x2003 Inter-Area-Prefix-LSA 4 0x2004 Inter-Area-Router-LSA 5 0x4005 AS-External-LSA 6 0x2006 Deprecated (may be reassigned) 7 0x2007 NSSA-LSA 8 0x0008 Link-LSA 9 0x2009 Intra-Area-Prefix-LSA LSA Function Code A.4.3. Router-LSAs Router-LSAs have LS type equal to 0x2001. Each router in an area originates one or more router-LSAs. The complete collection of router-LSAs originated by the router describe the state and cost of the router's interfaces to the area. For details concerning the construction of router-LSAs, see Section 4.4.3.2. Router-LSAs are only flooded throughout a single area. Coltun, et al. Standards Track [Page 73]
RFC 5340 OSPF for IPv6 July 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Age |0|0|1| 1 | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Sequence Number | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Checksum | Length | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0 |Nt|x|V|E|B| Options | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | 0 | Metric | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Interface ID | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Neighbor Interface ID | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Neighbor Router ID | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Type | 0 | Metric | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Interface ID | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Neighbor Interface ID | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Neighbor Router ID | +-+-+-+--+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | Router-LSA Format A single router may originate one or more router-LSAs, distinguished by their Link State IDs (which are chosen arbitrarily by the originating router). The Options field and V, E, and B bits should be the same in all router-LSAs from a single originator. However, in the case of a mismatch, the values in the LSA with the lowest Link State ID take precedence. When more than one router-LSA is received from a single router, the links are processed as if concatenated into a single LSA. Coltun, et al. Standards Track [Page 74]
RFC 5340 OSPF for IPv6 July 2008 Bit V When set, the router is an endpoint of one or more fully adjacent virtual links having the described area as transit area (V is for virtual link endpoint). Bit E When set, the router is an AS boundary router (E is for external). Bit B When set, the router is an area border router (B is for border). Bit x This bit was previously used by MOSPF (see [MOSPF]) and has been deprecated for OSPFv3. The bit should be set to 0 and ignored when received. It may be reassigned in the future. Bit Nt When set, the router is an NSSA border router that is unconditionally translating NSSA-LSAs into AS-external-LSAs (Nt stands for NSSA translation). Note that such routers have their NSSATranslatorRole area configuration parameter set to Always. (See [NSSA].) Options The optional capabilities supported by the router, as documented in Appendix A.2. The following fields are used to describe each router interface. The Type field indicates the kind of interface being described. It may be an interface to a transit network, a point-to-point connection to another router, or a virtual link. The values of all the other fields describing a router interface depend on the interface's Type field. Type The kind of interface being described. One of the following: Type Description --------------------------------------------------- 1 Point-to-point connection to another router 2 Connection to a transit network 3 Reserved 4 Virtual link Router Link Types Coltun, et al. Standards Track [Page 75]
RFC 5340 OSPF for IPv6 July 2008 Metric The cost of using this router interface for outbound traffic. Interface ID The Interface ID assigned to the interface being described. See Section 4.1.2 and Appendix C.3. Neighbor Interface ID The Interface ID the neighbor router has associated with the link, as advertised in the neighbor's Hello packets. For transit (type 2) links, the link's Designated Router is the neighbor described. For other link types, the sole adjacent neighbor is described. Neighbor Router ID The Router ID the of the neighbor router. For transit (type 2) links, the link's Designated Router is the neighbor described. For other link types, the sole adjacent neighbor is described. For transit (Type 2) links, the combination of Neighbor Interface ID and Neighbor Router ID allows the network-LSA for the attached link to be found in the link-state database. A.4.4. Network-LSAs Network-LSAs have LS type equal to 0x2002. A network-LSA is originated for each broadcast and NBMA link in the area that includes two or more adjacent routers. The network-LSA is originated by the link's Designated Router. The LSA describes all routers attached to the link including the Designated Router itself. The LSA's Link State ID field is set to the Interface ID that the Designated Router has been advertising in Hello packets on the link. The distance from the network to all attached routers is zero. This is why the Metric fields need not be specified in the network-LSA. For details concerning the construction of network-LSAs, see Section 4.4.3.3. Coltun, et al. Standards Track [Page 76]
RFC 5340 OSPF for IPv6 July 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Age |0|0|1| 2 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Checksum | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0 | Options | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Attached Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | Network-LSA Format Attached Router The Router IDs of each of the routers attached to the link. Actually, only those routers that are fully adjacent to the Designated Router are listed. The Designated Router includes itself in this list. The number of routers included can be deduced from the LSA header's length field. A.4.5. Inter-Area-Prefix-LSAs Inter-area-prefix-LSAs have LS type equal to 0x2003. These LSAs are the IPv6 equivalent of OSPF for IPv4's type 3 summary-LSAs (see Section 12.4.3 of [OSPFV2]). Originated by area border routers, they describe routes to IPv6 address prefixes that belong to other areas. A separate inter-area-prefix-LSA is originated for each IPv6 address prefix. For details concerning the construction of inter-area- prefix-LSAs, see Section 4.4.3.4. For stub areas, inter-area-prefix-LSAs can also be used to describe a (per-area) default route. Default summary routes are used in stub areas instead of flooding a complete set of external routes. When describing a default summary route, the inter-area-prefix-LSA's PrefixLength is set to 0. Coltun, et al. Standards Track [Page 77]
RFC 5340 OSPF for IPv6 July 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Age |0|0|1| 3 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Checksum | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0 | Metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | PrefixLength | PrefixOptions | 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Address Prefix | | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Inter-Area-Prefix-LSA Format Metric The cost of this route. Expressed in the same units as the interface costs in router-LSAs. When the inter-area-prefix-LSA is describing a route to a range of addresses (see Appendix C.2), the cost is set to the maximum cost to any reachable component of the address range. PrefixLength, PrefixOptions, and Address Prefix Representation of the IPv6 address prefix, as described in Appendix A.4.1. A.4.6. Inter-Area-Router-LSAs Inter-area-router-LSAs have LS type equal to 0x2004. These LSAs are the IPv6 equivalent of OSPF for IPv4's type 4 summary-LSAs (see Section 12.4.3 of [OSPFV2]). Originated by area border routers, they describe routes to AS boundary routers in other areas. To see why it is necessary to advertise the location of each ASBR, consult Section 16.4 in [OSPFV2]. Each LSA describes a route to a single router. For details concerning the construction of inter-area-router-LSAs, see Section 4.4.3.5. Coltun, et al. Standards Track [Page 78]
RFC 5340 OSPF for IPv6 July 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Age |0|0|1| 4 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Checksum | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0 | Options | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | 0 | Metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Destination Router ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Inter-Area-Router-LSA Format Options The optional capabilities supported by the router, as documented in Appendix A.2. Metric The cost of this route. Expressed in the same units as the interface costs in router-LSAs. Destination Router ID The Router ID of the router being described by the LSA. A.4.7. AS-External-LSAs AS-external-LSAs have LS type equal to 0x4005. These LSAs are originated by AS boundary routers and describe destinations external to the AS. Each LSA describes a route to a single IPv6 address prefix. For details concerning the construction of AS-external-LSAs, see Section 4.4.3.6. AS-external-LSAs can be used to describe a default route. Default routes are used when no specific route exists to the destination. When describing a default route, the AS-external-LSA's PrefixLength is set to 0. Coltun, et al. Standards Track [Page 79]
RFC 5340 OSPF for IPv6 July 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Age |0|1|0| 5 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Checksum | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | |E|F|T| Metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | PrefixLength | PrefixOptions | Referenced LS Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Address Prefix | | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | +- -+ | | +- Forwarding Address (Optional) -+ | | +- -+ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | External Route Tag (Optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Referenced Link State ID (Optional) | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ AS-external-LSA Format bit E The type of external metric. If bit E is set, the metric specified is a Type 2 external metric. This means the metric is considered larger than any intra-AS path. If bit E is zero, the specified metric is a Type 1 external metric. This means that it is expressed in the same units as other LSAs (i.e., the same units as the interface costs in router-LSAs). bit F If set, a Forwarding Address has been included in the LSA. bit T If set, an External Route Tag has been included in the LSA. Coltun, et al. Standards Track [Page 80]
RFC 5340 OSPF for IPv6 July 2008 Metric The cost of this route. Interpretation depends on the external type indication (bit E above). PrefixLength, PrefixOptions, and Address Prefix Representation of the IPv6 address prefix, as described in Appendix A.4.1. Referenced LS Type If non-zero, an LSA with this LS type is to be associated with this LSA (see Referenced Link State ID below). Forwarding address A fully qualified IPv6 address (128 bits). Included in the LSA if and only if bit F has been set. If included, data traffic for the advertised destination will be forwarded to this address. It MUST NOT be set to the IPv6 Unspecified Address (0:0:0:0:0:0:0:0) or an IPv6 Link-Local Address (Prefix FE80/10). While OSPFv3 routes are normally installed with link-local addresses, an OSPFv3 implementation advertising a forwarding address MUST advertise a global IPv6 address. This global IPv6 address may be the next-hop gateway for an external prefix or may be obtained through some other method (e.g., configuration). External Route Tag A 32-bit field that MAY be used to communicate additional information between AS boundary routers. Included in the LSA if and only if bit T has been set. Referenced Link State ID Included if and only if Reference LS Type is non-zero. If included, additional information concerning the advertised external route can be found in the LSA having LS type equal to "Referenced LS Type", Link State ID equal to "Referenced Link State ID", and Advertising Router the same as that specified in the AS-external-LSA's link-state header. This additional information is not used by the OSPF protocol itself. It may be used to communicate information between AS boundary routers. The precise nature of such information is outside the scope of this specification. All, none, or some of the fields labeled Forwarding address, External Route Tag, and Referenced Link State ID MAY be present in the AS- external-LSA (as indicated by the setting of bit F, bit T, and Referenced LS Type respectively). When present, Forwarding Address always comes first, External Route Tag next, and the Referenced Link State ID last. Coltun, et al. Standards Track [Page 81]
RFC 5340 OSPF for IPv6 July 2008 A.4.8. NSSA-LSAs NSSA-LSAs have LS type equal to 0x2007. These LSAs are originated by AS boundary routers within an NSSA and describe destinations external to the AS that may or may not be propagated outside the NSSA (refer to [NSSA]). Other than the LS type, their format is exactly the same as AS-external LSAs as described in Appendix A.4.7. A global IPv6 address MUST be selected as forwarding address for NSSA-LSAs that are to be propagated by NSSA area border routers. The selection should proceed the same as OSPFv2 NSSA support [NSSA] with additional checking to ensure IPv6 link-local address are not selected. A.4.9. Link-LSAs Link-LSAs have LS type equal to 0x0008. A router originates a separate link-LSA for each attached physical link. These LSAs have link-local flooding scope; they are never flooded beyond the associated link. Link-LSAs have three purposes: 1. They provide the router's link-local address to all other routers attached to the link. 2. They inform other routers attached to the link of a list of IPv6 prefixes to associate with the link. 3. They allow the router to advertise a collection of Options bits in the network-LSA originated by the Designated Router on a broadcast or NBMA link. For details concerning the construction of links-LSAs, see Section 4.4.3.8. A link-LSA's Link State ID is set equal to the originating router's Interface ID on the link. Coltun, et al. Standards Track [Page 82]
RFC 5340 OSPF for IPv6 July 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Age |0|0|0| 8 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Checksum | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Rtr Priority | Options | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | +- -+ | | +- Link-local Interface Address -+ | | +- -+ | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | # prefixes | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | PrefixLength | PrefixOptions | 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Address Prefix | | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | PrefixLength | PrefixOptions | 0 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Address Prefix | | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Link-LSA Format Rtr Priority The Router Priority of the interface attaching the originating router to the link. Options The set of Options bits that the router would like set in the network-LSA that will be originated by the Designated Router on broadcast or NBMA links. Coltun, et al. Standards Track [Page 83]
RFC 5340 OSPF for IPv6 July 2008 Link-local Interface Address The originating router's link-local interface address on the link. # prefixes The number of IPv6 address prefixes contained in the LSA. The rest of the link-LSA contains a list of IPv6 prefixes to be associated with the link. PrefixLength, PrefixOptions, and Address Prefix Representation of an IPv6 address prefix, as described in Appendix A.4.1. A.4.10. Intra-Area-Prefix-LSAs Intra-area-prefix-LSAs have LS type equal to 0x2009. A router uses intra-area-prefix-LSAs to advertise one or more IPv6 address prefixes that are associated with a local router address, an attached stub network segment, or an attached transit network segment. In IPv4, the first two were accomplished via the router's router-LSA and the last via a network-LSA. In OSPF for IPv6, all addressing information that was advertised in router-LSAs and network-LSAs has been removed and is now advertised in intra-area-prefix-LSAs. For details concerning the construction of intra-area-prefix-LSA, see Section 4.4.3.9. A router can originate multiple intra-area-prefix-LSAs for each router or transit network. Each such LSA is distinguished by its unique Link State ID. Coltun, et al. Standards Track [Page 84]
RFC 5340 OSPF for IPv6 July 2008 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Age |0|0|1| 9 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Sequence Number | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | LS Checksum | Length | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | # Prefixes | Referenced LS Type | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Referenced Link State ID | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Referenced Advertising Router | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | PrefixLength | PrefixOptions | Metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Address Prefix | | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | PrefixLength | PrefixOptions | Metric | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Address Prefix | | ... | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ Intra-Area-Prefix LSA Format # prefixes The number of IPv6 address prefixes contained in the LSA. Referenced LS Type, Referenced Link State ID, and Referenced Advertising Router Identifies the router-LSA or network-LSA with which the IPv6 address prefixes should be associated. If Referenced LS Type is 0x2001, the prefixes are associated with a router-LSA, Referenced Link State ID should be 0, and Referenced Advertising Router should be the originating router's Router ID. If Referenced LS Type is 0x2002, the prefixes are associated with a network-LSA, Referenced Link State ID should be the Interface ID of the link's Designated Router, and Referenced Advertising Router should be the Designated Router's Router ID. Coltun, et al. Standards Track [Page 85]
RFC 5340 OSPF for IPv6 July 2008 The rest of the intra-area-prefix-LSA contains a list of IPv6 prefixes to be associated with the router or transit link, as well as their associated costs. PrefixLength, PrefixOptions, and Address Prefix Representation of an IPv6 address prefix, as described in Appendix A.4.1. Metric The cost of this prefix. Expressed in the same units as the interface costs in router-LSAs. Appendix B. Architectural Constants Architectural constants for the OSPF protocol are defined in Appendix B of [OSPFV2]. The only difference for OSPF for IPv6 is that DefaultDestination is encoded as a prefix with length 0 (see Appendix A.4.1). Appendix C. Configurable Constants The OSPF protocol has quite a few configurable parameters. These parameters are listed below. They are grouped into general functional categories (area parameters, interface parameters, etc.). Sample values are given for some of the parameters. Some parameter settings need to be consistent among groups of routers. For example, all routers in an area must agree on that area's parameters. Similarly, all routers attached to a network must agree on that network's HelloInterval and RouterDeadInterval. Some parameters may be determined by router algorithms outside of this specification (e.g., the address of a host connected to the router via a SLIP line). From OSPF's point of view, these items are still configurable. C.1. Global Parameters In general, a separate copy of the OSPF protocol is run for each area. Because of this, most configuration parameters are defined on a per-area basis. The few global configuration parameters are listed below. Coltun, et al. Standards Track [Page 86]
RFC 5340 OSPF for IPv6 July 2008 Router ID This is a 32-bit number that uniquely identifies the router in the Autonomous System. If a router's OSPF Router ID is changed, the router's OSPF software should be restarted before the new Router ID takes effect. Before restarting due to a Router ID change, the router should flush its self-originated LSAs from the routing domain (see Section 14.1 of [OSPFV2]). Otherwise, they will persist for up to MaxAge seconds. Because the size of the Router ID is smaller than an IPv6 address, it cannot be set to one of the router's IPv6 addresses (as is commonly done for IPv4). Possible Router ID assignment procedures for IPv6 include: a) assign the IPv6 Router ID as one of the router's IPv4 addresses or b) assign IPv6 Router IDs through some local administrative procedure (similar to procedures used by manufacturers to assign product serial numbers). The Router ID of 0.0.0.0 is reserved and SHOULD NOT be used. C.2. Area Parameters All routers belonging to an area must agree on that area's configuration. Disagreements between two routers will lead to an inability for adjacencies to form between them, with a resulting hindrance to the flow of both routing protocol information and data traffic. The following items must be configured for an area: Area ID This is a 32-bit number that identifies the area. The Area ID of 0 is reserved for the backbone. List of address ranges Address ranges control the advertisement of routes across area boundaries. Each address range consists of the following items: [IPv6 prefix, prefix length] Describes the collection of IPv6 addresses contained in the address range. Status Set to either Advertise or DoNotAdvertise. Routing information is condensed at area boundaries. External to the area, at most a single route is advertised (via a inter-area-prefix-LSA) for each address range. The route is advertised if and only if the address range's Status is set to Advertise. Unadvertised ranges allow the existence of certain networks to be intentionally hidden from other areas. Status is set to Advertise by default. Coltun, et al. Standards Track [Page 87]
RFC 5340 OSPF for IPv6 July 2008 ExternalRoutingCapability Whether AS-external-LSAs will be flooded into/throughout the area. If AS-external-LSAs are excluded from the area, the area is called a stub area or NSSA. Internal to stub areas, routing to external destinations will be based solely on a default inter-area route. The backbone cannot be configured as a stub or NSSA area. Also, virtual links cannot be configured through stub or NSSA areas. For more information, see Section 3.6 of [OSPFV2] and [NSSA]. StubDefaultCost If the area has been configured as a stub area, and the router itself is an area border router, then the StubDefaultCost indicates the cost of the default inter-area-prefix-LSA that the router should advertise into the area. See Section 12.4.3.1 of [OSPFV2] for more information. NSSATranslatorRole and TranslatorStabilityInterval These area parameters are described in Appendix D of [NSSA]. Additionally, an NSSA Area Border Router (ABR) is also required to allow configuration of whether or not an NSSA default route is advertised in an NSSA-LSA. If advertised, its metric and metric type are configurable. These requirements are also described in Appendix D of [NSSA]. ImportSummaries When set to enabled, prefixes external to the area are imported into the area via the advertisement of inter-area-prefix-LSAs. When set to disabled, inter-area routes are not imported into the area. The default setting is enabled. This parameter is only valid for stub or NSSA areas. C.3. Router Interface Parameters Some of the configurable router interface parameters (such as Area ID, HelloInterval, and RouterDeadInterval) actually imply properties of the attached links. Therefore, these parameters must be consistent across all the routers attached to that link. The parameters that must be configured for a router interface are: IPv6 link-local address The IPv6 link-local address associated with this interface. May be learned through auto-configuration. Coltun, et al. Standards Track [Page 88]
RFC 5340 OSPF for IPv6 July 2008 Area ID The OSPF area to which the attached link belongs. Instance ID The OSPF protocol instance associated with this OSPF interface. Defaults to 0. Interface ID 32-bit number uniquely identifying this interface among the collection of this router's interfaces. For example, in some implementations it may be possible to use the MIB-II IfIndex ([INTFMIB]). IPv6 prefixes The list of IPv6 prefixes to associate with the link. These will be advertised in intra-area-prefix-LSAs. Interface output cost(s) The cost of sending a packet on the interface, expressed in the link-state metric. This is advertised as the link cost for this interface in the router's router-LSA. The interface output cost MUST always be greater than 0. RxmtInterval The number of seconds between LSA retransmissions for adjacencies belonging to this interface. Also used when retransmitting Database Description and Link State Request packets. This should be well over the expected round-trip delay between any two routers on the attached link. The setting of this value should be conservative or needless retransmissions will result. Sample value for a local area network: 5 seconds. InfTransDelay The estimated number of seconds it takes to transmit a Link State Update packet over this interface. LSAs contained in the update packet must have their age incremented by this amount before transmission. This value should take into account the transmission and propagation delays of the interface. It MUST be greater than 0. Sample value for a local area network: 1 second. Router Priority An 8-bit unsigned integer. When two routers attached to a network both attempt to become the Designated Router, the one with the highest Router Priority takes precedence. If there is still a tie, the router with the highest Router ID takes precedence. A router whose Router Priority is set to 0 is ineligible to become the Designated Router on the attached link. Router Priority is only configured for interfaces to broadcast and NBMA networks. Coltun, et al. Standards Track [Page 89]
RFC 5340 OSPF for IPv6 July 2008 HelloInterval The length of time, in seconds, between Hello packets that the router sends on the interface. This value is advertised in the router's Hello packets. It MUST be the same for all routers attached to a common link. The smaller the HelloInterval, the faster topological changes will be detected. However, more OSPF routing protocol traffic will ensue. Sample value for a X.25 PDN: 30 seconds. Sample value for a local area network (LAN): 10 seconds. RouterDeadInterval After ceasing to hear a router's Hello packets, the number of seconds before its neighbors declare the router down. This is also advertised in the router's Hello packets in their RouterDeadInterval field. This should be some multiple of the HelloInterval (e.g., 4). This value again MUST be the same for all routers attached to a common link. LinkLSASuppression Indicates whether or not origination of a link-LSA is suppressed. If set to "enabled" and the interface type is not broadcast or NBMA, the router will not originate a link-LSA for the link. This implies that other routers on the link will ascertain the router's next-hop address using a mechanism other than the link-LSA (see Section 4.8.2). The default value is "disabled" for interface types described in this specification. It is implicitly "disabled" if the interface type is broadcast or NBMA. Future interface types MAY specify a different default. C.4. Virtual Link Parameters Virtual links are used to restore/increase connectivity of the backbone. Virtual links may be configured between any pair of area border routers having interfaces to a common (non-backbone) area. The virtual link appears as a point-to-point link with no global IPv6 addresses in the graph for the backbone. The virtual link must be configured in both of the area border routers. A virtual link appears in router-LSAs (for the backbone) as if it were a separate router interface to the backbone. As such, it has most of the parameters associated with a router interface (see Appendix C.3). Virtual links do not have link-local addresses, but instead use one of the router's global-scope IPv6 addresses as the IP source in OSPF protocol packets it sends on the virtual link. Router Priority is not used on virtual links. Interface output cost is not configured on virtual links, but is dynamically set to be the cost of the transit area intra-area path between the two endpoint routers. The parameter RxmtInterval may be configured and should be well over Coltun, et al. Standards Track [Page 90]
RFC 5340 OSPF for IPv6 July 2008 the expected round-trip delay between the two routers. This may be hard to estimate for a virtual link; it is better to err on the side of making it too long. A virtual link is defined by the following two configurable parameters: the Router ID of the virtual link's other endpoint and the (non-backbone) area that the virtual link traverses (referred to as the virtual link's transit area). Virtual links cannot be configured through stub or NSSA areas. Additionally, an Instance ID may be configured for virtual links from different protocol instances in order to utilize the same transit area (without requiring different Router IDs for demultiplexing). C.5. NBMA Network Parameters OSPF treats an NBMA network much like it treats a broadcast network. Since there may be many routers attached to the network, a Designated Router is selected for the network. This Designated Router then originates a network-LSA listing all routers attached to the NBMA network. However, due to the lack of broadcast capabilities, it may be necessary to use configuration parameters in the Designated Router selection. These parameters will only need to be configured in those routers that are themselves eligible to become the Designated Router (i.e., those routers whose Router Priority for the network is non- zero), and then only if no automatic procedure for discovering neighbors exists: List of all other attached routers The list of all other routers attached to the NBMA network. Each router is configured with its Router ID and IPv6 link-local address on the network. Also, for each router listed, that router's eligibility to become the Designated Router must be defined. When an interface to an NBMA network first comes up, the router only sends Hello packets to those neighbors eligible to become the Designated Router until such time that a Designated Router is elected. PollInterval If a neighboring router has become inactive (Hello packets have not been seen for RouterDeadInterval seconds), it may still be necessary to send Hello packets to the dead neighbor. These Hello packets will be sent at the reduced rate PollInterval, which should be much larger than HelloInterval. Sample value for a PDN X.25 network: 2 minutes. Coltun, et al. Standards Track [Page 91]
RFC 5340 OSPF for IPv6 July 2008 C.6. Point-to-Multipoint Network Parameters On point-to-multipoint networks, it may be necessary to configure the set of neighbors that are directly reachable over the point-to- multipoint network. Each neighbor is configured with its Router ID and IPv6 link-local address on the network. Designated Routers are not elected on point-to-multipoint networks, so the Designated Router eligibility of configured neighbors is not defined. C.7. Host Route Parameters Host prefixes are advertised in intra-area-prefix-LSAs. They indicate either local router addresses, router interfaces to point- to-point networks, looped router interfaces, or IPv6 hosts that are directly connected to the router (e.g., via a PPP connection). For each host directly connected to the router, the following items must be configured: Host IPv6 prefix An IPv6 prefix belonging to the directly connected host. This must not be a valid IPv6 global prefix. Cost of link to host The cost of sending a packet to the host, in terms of the link- state metric. However, since the host probably has only a single connection to the Internet, the actual configured cost(s) in many cases is unimportant (i.e., will have no effect on routing). Area ID The OSPF area to which the host's prefix belongs. Coltun, et al. Standards Track [Page 92]
RFC 5340 OSPF for IPv6 July 2008 Authors' Addresses Rob Coltun Acoustra Productions 3204 Brooklawn Terrace Chevy Chase, MD 20815 USA Dennis Ferguson Juniper Networks 1194 N. Mathilda Avenue Sunnyvale, CA 94089 USA EMail: dennis@juniper.net John Moy Sycamore Networks, Inc 10 Elizabeth Drive Chelmsford, MA 01824 USA EMail: jmoy@sycamorenet.com Acee Lindem (editor) Redback Networks 102 Carric Bend Court Cary, NC 27519 USA EMail: acee@redback.com Coltun, et al. Standards Track [Page 93]
RFC 5340 OSPF for IPv6 July 2008 Full Copyright Statement Copyright (C) The IETF Trust (2008). This document is subject to the rights, licenses and restrictions contained in BCP 78, and except as set forth therein, the authors retain all their rights. This document and the information contained herein are provided on an "AS IS" basis and THE CONTRIBUTOR, THE ORGANIZATION HE/SHE REPRESENTS OR IS SPONSORED BY (IF ANY), THE INTERNET SOCIETY, THE IETF TRUST AND THE INTERNET ENGINEERING TASK FORCE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Intellectual Property The IETF takes no position regarding the validity or scope of any Intellectual Property Rights or other rights that might be claimed to pertain to the implementation or use of the technology described in this document or the extent to which any license under such rights might or might not be available; nor does it represent that it has made any independent effort to identify any such rights. Information on the procedures with respect to rights in RFC documents can be found in BCP 78 and BCP 79. Copies of IPR disclosures made to the IETF Secretariat and any assurances of licenses to be made available, or the result of an attempt made to obtain a general license or permission for the use of such proprietary rights by implementers or users of this specification can be obtained from the IETF on-line IPR repository at http://www.ietf.org/ipr. The IETF invites any interested party to bring to its attention any copyrights, patents or patent applications, or other proprietary rights that may cover technology that may be required to implement this standard. Please address the information to the IETF at ietf-ipr@ietf.org. Coltun, et al. Standards Track [Page 94]