[Note that this file is a concatenation of more than one RFC.]
Network Working Group
Request for Comments: 1001 March, 1987
PROTOCOL STANDARD FOR A NetBIOS SERVICE
ON A TCP/UDP TRANSPORT:
CONCEPTS AND METHODS
ABSTRACT
This RFC defines a proposed standard protocol to support NetBIOS
services in a TCP/IP environment. Both local network and internet
operation are supported. Various node types are defined to accommodate
local and internet topologies and to allow operation with or without the
use of IP broadcast.
This RFC describes the NetBIOS-over-TCP protocols in a general manner,
emphasizing the underlying ideas and techniques. Detailed
specifications are found in a companion RFC, "Protocol Standard For a
NetBIOS Service on a TCP/UDP Transport: Detailed Specifications".
NetBIOS Working Group [Page 1]
RFC 1001 March 1987
SUMMARY OF CONTENTS
1. STATUS OF THIS MEMO 6
2. ACKNOWLEDGEMENTS 6
3. INTRODUCTION 7
4. DESIGN PRINCIPLES 7
5. OVERVIEW OF NetBIOS 10
6. NetBIOS FACILITIES SUPPORTED BY THIS STANDARD 15
7. REQUIRED SUPPORTING SERVICE INTERFACES AND DEFINITIONS 15
8. RELATED PROTOCOLS AND SERVICES 16
9. NetBIOS SCOPE 16
10. NetBIOS END-NODES 16
11. NetBIOS SUPPORT SERVERS 18
12. TOPOLOGIES 20
13. GENERAL METHODS 23
14. REPRESENTATION OF NETBIOS NAMES 25
15. NetBIOS NAME SERVICE 27
16. NetBIOS SESSION SERVICE 48
17. NETBIOS DATAGRAM SERVICE 55
18. NODE CONFIGURATION PARAMETERS 58
19. MINIMAL CONFORMANCE 59
REFERENCES 60
APPENDIX A - INTEGRATION WITH INTERNET GROUP MULTICASTING 61
APPENDIX B - IMPLEMENTATION CONSIDERATIONS 62
NetBIOS Working Group [Page 2]
RFC 1001 March 1987
TABLE OF CONTENTS
1. STATUS OF THIS MEMO 6
2. ACKNOWLEDGEMENTS 6
3. INTRODUCTION 7
4. DESIGN PRINCIPLES 8
4.1 PRESERVE NetBIOS SERVICES 8
4.2 USE EXISTING STANDARDS 8
4.3 MINIMIZE OPTIONS 8
4.4 TOLERATE ERRORS AND DISRUPTIONS 8
4.5 DO NOT REQUIRE CENTRAL MANAGEMENT 9
4.6 ALLOW INTERNET OPERATION 9
4.7 MINIMIZE BROADCAST ACTIVITY 9
4.8 PERMIT IMPLEMENTATION ON EXISTING SYSTEMS 9
4.9 REQUIRE ONLY THE MINIMUM NECESSARY TO OPERATE 9
4.10 MAXIMIZE EFFICIENCY 10
4.11 MINIMIZE NEW INVENTIONS 10
5. OVERVIEW OF NetBIOS 10
5.1 INTERFACE TO APPLICATION PROGRAMS 10
5.2 NAME SERVICE 11
5.3 SESSION SERVICE 12
5.4 DATAGRAM SERVICE 13
5.5 MISCELLANEOUS FUNCTIONS 14
5.6 NON-STANDARD EXTENSIONS 15
6. NetBIOS FACILITIES SUPPORTED BY THIS STANDARD 15
7. REQUIRED SUPPORTING SERVICE INTERFACES AND DEFINITIONS 15
8. RELATED PROTOCOLS AND SERVICES 16
9. NetBIOS SCOPE 16
10. NetBIOS END-NODES 16
10.1 BROADCAST (B) NODES 16
10.2 POINT-TO-POINT (P) NODES 16
10.3 MIXED MODE (M) NODES 16
11. NetBIOS SUPPORT SERVERS 18
11.1 NetBIOS NAME SERVER (NBNS) NODES 18
11.1.1 RELATIONSHIP OF THE NBNS TO THE DOMAIN NAME SYSTEM 19
11.2 NetBIOS DATAGRAM DISTRIBUTION SERVER (NBDD) NODES 19
11.3 RELATIONSHIP OF NBNS AND NBDD NODES 20
11.4 RELATIONSHIP OF NetBIOS SUPPORT SERVERS AND B NODES 20
12. TOPOLOGIES 20
12.1 LOCAL 20
NetBIOS Working Group [Page 3]
RFC 1001 March 1987
12.1.1 B NODES ONLY 21
12.1.2 P NODES ONLY 21
12.1.3 MIXED B AND P NODES 21
12.2 INTERNET 22
12.2.1 P NODES ONLY 22
12.2.2 MIXED M AND P NODES 23
13. GENERAL METHODS 23
13.1 REQUEST/RESPONSE INTERACTION STYLE 23
13.1.1 RETRANSMISSION OF REQUESTS 24
13.1.2 REQUESTS WITHOUT RESPONSES: DEMANDS 24
13.2 TRANSACTIONS 25
13.2.1 TRANSACTION ID 25
13.3 TCP AND UDP FOUNDATIONS 25
14. REPRESENTATION OF NETBIOS NAMES 25
14.1 FIRST LEVEL ENCODING 26
14.2 SECOND LEVEL ENCODING 27
15. NetBIOS NAME SERVICE 27
15.1 OVERVIEW OF NetBIOS NAME SERVICE 27
15.1.1 NAME REGISTRATION (CLAIM) 27
15.1.2 NAME QUERY (DISCOVERY) 28
15.1.3 NAME RELEASE 28
15.1.3.1 EXPLICIT RELEASE 28
15.1.3.2 NAME LIFETIME AND REFRESH 29
15.1.3.3 NAME CHALLENGE 29
15.1.3.4 GROUP NAME FADE-OUT 29
15.1.3.5 NAME CONFLICT 30
15.1.4 ADAPTER STATUS 31
15.1.5 END-NODE NBNS INTERACTION 31
15.1.5.1 UDP, TCP, AND TRUNCATION 31
15.1.5.2 NBNS WACK 32
15.1.5.3 NBNS REDIRECTION 32
15.1.6 SECURED VERSUS NON-SECURED NBNS 32
15.1.7 CONSISTENCY OF THE NBNS DATA BASE 32
15.1.8 NAME CACHING 34
15.2 NAME REGISTRATION TRANSACTIONS 34
15.2.1 NAME REGISTRATION BY B NODES 34
15.2.2 NAME REGISTRATION BY P NODES 35
15.2.2.1 NEW NAME, OR NEW GROUP MEMBER 35
15.2.2.2 EXISTING NAME AND OWNER IS STILL ACTIVE 36
15.2.2.3 EXISTING NAME AND OWNER IS INACTIVE 37
15.2.3 NAME REGISTRATION BY M NODES 38
15.3 NAME QUERY TRANSACTIONS 39
15.3.1 QUERY BY B NODES 39
15.3.2 QUERY BY P NODES 40
15.3.3 QUERY BY M NODES 43
15.3.4 ACQUIRE GROUP MEMBERSHIP LIST 43
15.4 NAME RELEASE TRANSACTIONS 44
15.4.1 RELEASE BY B NODES 44
NetBIOS Working Group [Page 4]
RFC 1001 March 1987
15.4.2 RELEASE BY P NODES 44
15.4.3 RELEASE BY M NODES 44
15.5 NAME MAINTENANCE TRANSACTIONS 45
15.5.1 NAME REFRESH 45
15.5.2 NAME CHALLENGE 46
15.5.3 CLEAR NAME CONFLICT 47
15.6 ADAPTER STATUS TRANSACTIONS 47
16. NetBIOS SESSION SERVICE 48
16.1 OVERVIEW OF NetBIOS SESSION SERVICE 49
16.1.1 SESSION ESTABLISHMENT PHASE OVERVIEW 49
16.1.1.1 RETRYING AFTER BEING RETARGETTED 50
16.1.1.2 SESSION ESTABLISHMENT TO A GROUP NAME 51
16.1.2 STEADY STATE PHASE OVERVIEW 51
16.1.3 SESSION TERMINATION PHASE OVERVIEW 51
16.2 SESSION ESTABLISHMENT PHASE 52
16.3 SESSION DATA TRANSFER PHASE 54
16.3.1 DATA ENCAPSULATION 54
16.3.2 SESSION KEEP-ALIVES 54
17. NETBIOS DATAGRAM SERVICE 55
17.1 OVERVIEW OF NetBIOS DATAGRAM SERVICE 55
17.1.1 UNICAST, MULTICAST, AND BROADCAST 55
17.1.2 FRAGMENTATION OF NetBIOS DATAGRAMS 55
17.2 NetBIOS DATAGRAMS BY B NODES 57
17.3 NetBIOS DATAGRAMS BY P AND M NODES 58
18. NODE CONFIGURATION PARAMETERS 58
19. MINIMAL CONFORMANCE 59
REFERENCES 60
APPENDIX A 61
INTEGRATION WITH INTERNET GROUP MULTICASTING 61
A-1. ADDITIONAL PROTOCOL REQUIRED IN B AND M NODES 61
A-2. CONSTRAINTS 61
APPENDIX B 62
IMPLEMENTATION CONSIDERATIONS 62
B-1. IMPLEMENTATION MODELS 62
B-1.1 MODEL INDEPENDENT CONSIDERATIONS 63
B-1.2 SERVICE OPERATION FOR EACH MODEL 63
B-2. CASUAL AND RESTRICTED NetBIOS APPLICATIONS 64
B-3. TCP VERSUS SESSION KEEP-ALIVES 66
B-4. RETARGET ALGORITHMS 67
B-5. NBDD SERVICE 68
B-6. APPLICATION CONSIDERATIONS 68
B-6.1 USE OF NetBIOS DATAGRAMS 68
NetBIOS Working Group [Page 5]
RFC 1001 March 1987
PROTOCOL STANDARD FOR A NetBIOS SERVICE
ON A TCP/UDP TRANSPORT:
CONCEPTS AND METHODS
1. STATUS OF THIS MEMO
This RFC specifies a proposed standard for the Internet
community. Since this topic is new to the Internet community,
discussions and suggestions are specifically requested.
Please send written comments to:
Karl Auerbach
Epilogue Technology Corporation
P.O. Box 5432
Redwood City, CA 94063
Please send online comments to:
Avnish Aggarwal
Internet: mtxinu!excelan!avnish@ucbvax.berkeley.edu
Usenet: ucbvax!mtxinu!excelan!avnish
Distribution of this document is unlimited.
2. ACKNOWLEDGEMENTS
This RFC has been developed under the auspices of the Internet
Activities Board, especially the End-to-End Services Task Force.
The following individuals have contributed to the development of
this RFC:
Avnish Aggarwal Arvind Agrawal Lorenzo Aguilar
Geoffrey Arnold Karl Auerbach K. Ramesh Babu
Keith Ball Amatzia Ben-Artzi Vint Cerf
Richard Cherry David Crocker Steve Deering
Greg Ennis Steve Holmgren Jay Israel
David Kaufman Lee LaBarre James Lau
Dan Lynch Gaylord Miyata David Stevens
Steve Thomas Ishan Wu
The system proposed by this RFC does not reflect any existing
Netbios-over-TCP implementation. However, the design
incorporates considerable knowledge obtained from prior
implementations. Special thanks goes to the following
organizations which have provided this invaluable information:
CMC/Syros Excelan Sytek Ungermann-Bass
NetBIOS Working Group [Page 6]
RFC 1001 March 1987
3. INTRODUCTION
This RFC describes the ideas and general methods used to provide
NetBIOS on a TCP and UDP foundation. A companion RFC, "Protocol
Standard For a NetBIOS Service on a TCP/UDP Transport: Detailed
Specifications"[1] contains detailed descriptions of packet
formats, protocols, and defined constants and variables.
The NetBIOS service has become the dominant mechanism for
personal computer networking. NetBIOS provides a vendor
independent interface for the IBM Personal Computer (PC) and
compatible systems.
NetBIOS defines a software interface not a protocol. There is no
"official" NetBIOS service standard. In practice, however, the
IBM PC-Network version is used as a reference. That version is
described in the IBM document 6322916, "Technical Reference PC
Network"[2].
Protocols supporting NetBIOS services have been constructed on
diverse protocol and hardware foundations. Even when the same
foundation is used, different implementations may not be able to
interoperate unless they use a common protocol. To allow NetBIOS
interoperation in the Internet, this RFC defines a standard
protocol to support NetBIOS services using TCP and UDP.
NetBIOS has generally been confined to personal computers to
date. However, since larger computers are often well suited to
run certain NetBIOS applications, such as file servers, this
specification has been designed to allow an implementation to be
built on virtually any type of system where the TCP/IP protocol
suite is available.
This standard defines a set of protocols to support NetBIOS
services.
These protocols are more than a simple communications service
involving two entities. Rather, this note describes a
distributed system in which many entities play a part even if
they are not involved as an end-point of a particular NetBIOS
connection.
This standard neither constrains nor determines how those
services are presented to application programs.
Nevertheless, it is expected that on computers operating under
the PC-DOS and MS-DOS operating systems that the existing NetBIOS
interface will be preserved by implementors.
NOTE: Various symbolic values are used in this document. For
their definitions, refer to the Detailed Specifications[1].
NetBIOS Working Group [Page 7]
RFC 1001 March 1987
4. DESIGN PRINCIPLES
In order to develop the specification the following design principles
were adopted to guide the effort. Most are typical to any protocol
standardization effort; however, some have been assigned priorities
that may be considered unusual.
4.1. PRESERVE NetBIOS SERVICES
In the absence of an "official" standard for NetBIOS services, the
version found in the IBM PC Network Technical Reference[2] is used.
NetBIOS is the foundation of a large body of existing applications.
It is desirable to operate these applications on TCP networks and to
extend them beyond personal computers into larger hosts. To support
these applications, NetBIOS on TCP must closely conform to the
services offered by existing NetBIOS systems.
IBM PC-Network NetBIOS contains some implementation specific
characteristics. This standard does not attempt to completely
preserve these. It is certain that some existing software requires
these characteristics and will fail to operate correctly on a NetBIOS
service based on this RFC.
4.2. USE EXISTING STANDARDS
Protocol development, especially with standardization, is a demanding
process. The development of new protocols must be minimized.
It is considered essential that an existing standard which provides
the necessary functionality with reasonable performance always be
chosen in preference to developing a new protocol.
When a standard protocol is used, it must be unmodified.
4.3. MINIMIZE OPTIONS
The standard for NetBIOS on TCP should contain few, if any, options.
Where options are included, the options should be designed so that
devices with different option selections should interoperate.
4.4. TOLERATE ERRORS AND DISRUPTIONS
NetBIOS networks typically operate in an uncontrolled environment.
Computers come on-line at arbitrary times. Computers usually go
off-line without any notice to their peers. The software is often
operated by users who are unfamiliar with networks and who may
randomly perturb configuration settings.
Despite this chaos, NetBIOS networks work. NetBIOS on TCP must also
NetBIOS Working Group [Page 8]
RFC 1001 March 1987
be able to operate well in this environment.
Robust operation does not necessarily mean that the network is proof
against all disruptions. A typical NetBIOS network may be disrupted
by certain types of behavior, whether inadvertent or malicious.
4.5. DO NOT REQUIRE CENTRAL MANAGEMENT
NetBIOS on TCP should be able to operate, if desired, without
centralized management beyond that typically required by a TCP based
network.
4.6. ALLOW INTERNET OPERATION
The proposed standard recognizes the need for NetBIOS operation
across a set of networks interconnected by network (IP) level relays
(gateways.)
However, the standard assumes that this form of operation will be
less frequent than on the local MAC bridged-LAN.
4.7. MINIMIZE BROADCAST ACTIVITY
The standard pre-supposes that the only broadcast services are those
supported by UDP. Multicast capabilities are not assumed to be
available in any form.
Despite the availability of broadcast capabilities, the standard
recognizes that some administrations may wish to avoid heavy
broadcast activity. For example, an administration may wish to avoid
isolated non-participating hosts from the burden of receiving and
discarding NetBIOS broadcasts.
4.8. PERMIT IMPLEMENTATION ON EXISTING SYSTEMS
The NetBIOS on TCP protocol should be implementable on common
operating systems, such as Unix(tm) and VAX/VMS(tm), without massive
effort.
The NetBIOS protocols should not require services typically
unavailable on presently existing TCP/UDP/IP implementations.
4.9. REQUIRE ONLY THE MINIMUM NECESSARY TO OPERATE
The protocol definition should specify only the minimal set of
protocols required for interoperation. However, additional protocol
elements may be defined to enhance efficiency. These latter elements
may be generated at the option of the sender, although they must be
accepted by all receivers.
NetBIOS Working Group [Page 9]
RFC 1001 March 1987
4.10. MAXIMIZE EFFICIENCY
To be useful, a protocol must conduct its business quickly.
4.11. MINIMIZE NEW INVENTIONS
When an existing protocol is not quite able to support a necessary
function, but with a small amount of change, it could, that protocol
should be used. This is felt to be easier to achieve than
development of new protocols; further, it is likely to have more
general utility for the Internet.
5. OVERVIEW OF NetBIOS
This section describes the NetBIOS services. It is for background
information only. The reader may chose to skip to the next section.
NetBIOS was designed for use by groups of PCs, sharing a broadcast
medium. Both connection (Session) and connectionless (Datagram)
services are provided, and broadcast and multicast are supported.
Participants are identified by name. Assignment of names is
distributed and highly dynamic.
NetBIOS applications employ NetBIOS mechanisms to locate resources,
establish connections, send and receive data with an application
peer, and terminate connections. For purposes of discussion, these
mechanisms will collectively be called the NetBIOS Service.
This service can be implemented in many different ways. One of the
first implementations was for personal computers running the PC-DOS
and MS-DOS operating systems. It is possible to implement NetBIOS
within other operating systems, or as processes which are,
themselves, simply application programs as far as the host operating
system is concerned.
The NetBIOS specification, published by IBM as "Technical Reference
PC Network"[2] defines the interface and services available to the
NetBIOS user. The protocols outlined by that document pertain only
to the IBM PC Network and are not generally applicable to other
networks.
5.1. INTERFACE TO APPLICATION PROGRAMS
NetBIOS on personal computers includes both a set of services and an
exact program interface to those services. NetBIOS on other computer
systems may present the NetBIOS services to programs using other
interfaces. Except on personal computers, no clear standard for a
NetBIOS software interface has emerged.
NetBIOS Working Group [Page 10]
RFC 1001 March 1987
5.2. NAME SERVICE
NetBIOS resources are referenced by name. Lower-level address
information is not available to NetBIOS applications. An
application, representing a resource, registers one or more names
that it wishes to use.
The name space is flat and uses sixteen alphanumeric characters.
Names may not start with an asterisk (*).
Registration is a bid for use of a name. The bid may be for
exclusive (unique) or shared (group) ownership. Each application
contends with the other applications in real time. Implicit
permission is granted to a station when it receives no objections.
That is, a bid is made and the application waits for a period of
time. If no objections are received, the station assumes that it has
permission.
A unique name should be held by only one station at a time. However,
duplicates ("name conflicts") may arise due to errors.
All instances of a group name are equivalent.
An application referencing a name generally does not know (or care)
whether the name is registered as a unique or a group name.
An explicit name deletion function is specified, so that applications
may remove a name. Implicit name deletion occurs when a station
ceases operation. In the case of personal computers, implicit name
deletion is a frequent occurrence.
The Name Service primitives are:
1) Add Name
The requesting application wants exclusive use of the name.
2) Add Group Name
The requesting application is willing to share use of the
name with other applications.
3) Delete Name
The application no longer requires use of the name. It is
important to note that typical use of NetBIOS is among
independently-operated personal computers. A common way to
stop using a PC is to turn it off; in this case, the
graceful give-back mechanism, provided by the Delete Name
function, is not used. Because this occurs frequently, the
network service must support this behavior.
NetBIOS Working Group [Page 11]
RFC 1001 March 1987
5.3. SESSION SERVICE
A session is a reliable message exchange, conducted between a pair of
NetBIOS applications. Sessions are full-duplex, sequenced, and
reliable. Data is organized into messages. Each message may range
in size from 0 to 131,071 bytes. No expedited or urgent data
capabilities are present.
Multiple sessions may exist between any pair of calling and called
names.
The parties to a connection have access to the calling and called
names.
The NetBIOS specification does not define how a connection request to
a shared (group) name resolves into a session. The usual assumption
is that a session may be established with any one owner of the called
group name.
An important service provided to NetBIOS applications is the
detection of sessions failure. The loss of a session is reported to
an application via all of the outstanding service requests for that
session. For example, if the application has only a NetBIOS receive
primitive pending and the session terminates, the pending receive
will abort with a termination indication.
Session Service primitives are:
1) Call
Initiate a session with a process that is listening under
the specified name. The calling entity must indicate both a
calling name (properly registered to the caller) and a
called name.
2) Listen
Accept a session from a caller. The listen primitive may be
constrained to accept an incoming call from a named caller.
Alternatively, a call may be accepted from any caller.
3) Hang Up
Gracefully terminate a session. All pending data is
transferred before the session is terminated.
4) Send
Transmit one message. A time-out can occur. A time-out of
any session send forces the non-graceful termination of the
session.
NetBIOS Working Group [Page 12]
RFC 1001 March 1987
A "chain send" primitive is required by the PC NetBIOS
software interface to allow a single message to be gathered
from pieces in various buffers. Chain Send is an interface
detail and does not effect the protocol.
5) Receive
Receive data. A time-out can occur. A time-out on a
session receive only terminates the receive, not the
session, although the data is lost.
The receive primitive may be implemented with variants, such
as "Receive Any", which is required by the PC NetBIOS
software interface. Receive Any is an interface detail and
does not effect the protocol.
6) Session Status
Obtain information about all of the requestor's sessions,
under the specified name. No network activity is involved.
5.4. DATAGRAM SERVICE
The Datagram service is an unreliable, non-sequenced, connectionless
service. Datagrams are sent under cover of a name properly
registered to the sender.
Datagrams may be sent to a specific name or may be explicitly
broadcast.
Datagrams sent to an exclusive name are received, if at all, by the
holder of that name. Datagrams sent to a group name are multicast to
all holders of that name. The sending application program cannot
distinguish between group and unique names and thus must act as if
all non-broadcast datagrams are multicast.
As with the Session Service, the receiver of the datagram is told the
sending and receiving names.
Datagram Service primitives are:
1) Send Datagram
Send an unreliable datagram to an application that is
associated with the specified name. The name may be unique
or group; the sender is not aware of the difference. If the
name belongs to a group, then each member is to receive the
datagram.
NetBIOS Working Group [Page 13]
RFC 1001 March 1987
2) Send Broadcast Datagram
Send an unreliable datagram to any application with a
Receive Broadcast Datagram posted.
3) Receive Datagram
Receive a datagram sent by a specified originating name to
the specified name. If the originating name is an asterisk,
then the datagram may have been originated under any name.
Note: An arriving datagram will be delivered to all pending
Receiving Datagrams that have source and destination
specifications matching those of the datagram. In other
words, if a program (or group of programs) issue a series of
identical Receive Datagrams, one datagram will cause the
entire series to complete.
4) Receive Broadcast Datagram
Receive a datagram sent as a broadcast.
If there are multiple pending Receive Broadcast Datagram
operations pending, all will be satisfied by the same
received datagram.
5.5. MISCELLANEOUS FUNCTIONS
The following functions are present to control the operation of the
hardware interface to the network. These functions are generally
implementation dependent.
1) Reset
Initialize the local network adapter.
2) Cancel
Abort a pending NetBIOS request. The successful cancel of a
Send (or Chain Send) operation will terminate the associated
session.
3) Adapter Status
Obtain information about the local network adapter or of a
remote adapter.
4) Unlink
For use with Remote Program Load (RPL). Unlink redirects
the PC boot disk device back to the local disk. See the
NetBIOS Working Group [Page 14]
RFC 1001 March 1987
NetBIOS specification for further details concerning RPL and
the Unlink operation (see page 2-35 in [2]).
5) Remote Program Load
Remote Program Load (RPL) is not a NetBIOS function. It is
a NetBIOS application defined by IBM in their NetBIOS
specification (see pages 2-80 through 2-82 in [2]).
5.6. NON-STANDARD EXTENSIONS
The IBM Token Ring implementation of NetBIOS has added at least one
new user capability:
1) Find Name
This function determines whether a given name has been
registered on the network.
6. NetBIOS FACILITIES SUPPORTED BY THIS STANDARD
The protocol specified by this standard permits an implementer to
provide all of the NetBIOS services as described in the IBM
"Technical Reference PC Network"[2].
The following NetBIOS facilities are outside the scope of this
specification. These are local implementation matters and do not
impact interoperability:
- RESET
- SESSION STATUS
- UNLINK
- RPL (Remote Program Load)
7. REQUIRED SUPPORTING SERVICE INTERFACES AND DEFINITIONS
The protocols described in this RFC require service interfaces to the
following:
- TCP[3,4]
- UDP[5]
Byte ordering, addressing conventions (including addresses to be
used for broadcasts and multicasts) are defined by the most
recent version of:
- Assigned Numbers[6]
Additional definitions and constraints are in:
NetBIOS Working Group [Page 15]
RFC 1001 March 1987
- IP[7]
- Internet Subnets[8,9,10]
8. RELATED PROTOCOLS AND SERVICES
The design of the protocols described in this RFC allow for the
future incorporation of the following protocols and services.
However, before this may occur, certain extensions may be required to
the protocols defined in this RFC or to those listed below.
- Domain Name Service[11,12,13,14]
- Internet Group Multicast[15,16]
9. NetBIOS SCOPE
A "NetBIOS Scope" is the population of computers across which a
registered NetBIOS name is known. NetBIOS broadcast and multicast
datagram operations must reach the entire extent of the NetBIOS
scope.
An internet may support multiple, non-intersecting NetBIOS Scopes.
Each NetBIOS scope has a "scope identifier". This identifier is a
character string meeting the requirements of the domain name system
for domain names.
NOTE: Each implementation of NetBIOS-over-TCP must provide
mechanisms to manage the scope identifier(s) to be used.
Control of scope identifiers implies a requirement for additional
NetBIOS interface capabilities. These may be provided through
extensions of the user service interface or other means (such as node
configuration parameters.) The nature of these extensions is not
part of this specification.
10. NetBIOS END-NODES
End-nodes support NetBIOS service interfaces and contain
applications.
Three types of end-nodes are part of this standard:
- Broadcast ("B") nodes
- Point-to-point ("P") nodes
- Mixed mode ("M") nodes
An IP address may be associated with only one instance of one of the
above types.
Without having preloaded name-to-address tables, NetBIOS participants
NetBIOS Working Group [Page 16]
RFC 1001 March 1987
are faced with the task of dynamically resolving references to one
another. This can be accomplished with broadcast or mediated point-
to-point communications.
B nodes use local network broadcasting to effect a rendezvous with
one or more recipients. P and M nodes use the NetBIOS Name Server
(NBNS) and the NetBIOS Datagram Distribution Server (NBDD) for this
same purpose.
End-nodes may be combined in various topologies. No matter how
combined, the operation of the B, P, and M nodes is not altered.
NOTE: It is recommended that the administration of a NetBIOS
scope avoid using both M and B nodes within the same scope.
A NetBIOS scope should contain only B nodes or only P and M
nodes.
10.1. BROADCAST (B) NODES
Broadcast (or "B") nodes communicate using a mix of UDP datagrams
(both broadcast and directed) and TCP connections. B nodes may
freely interoperate with one another within a broadcast area. A
broadcast area is a single MAC-bridged "B-LAN". (See Appendix A for
a discussion of using Internet Group Multicasting as a means to
extend a broadcast area beyond a single B-LAN.)
10.2. POINT-TO-POINT (P) NODES
Point-to-point (or "P") nodes communicate using only directed UDP
datagrams and TCP sessions. P nodes neither generate nor listen for
broadcast UDP packets. P nodes do, however, offer NetBIOS level
broadcast and multicast services using capabilities provided by the
NBNS and NBDD.
P nodes rely on NetBIOS name and datagram distribution servers.
These servers may be local or remote; P nodes operate the same in
either case.
10.3. MIXED MODE (M) NODES
Mixed mode nodes (or "M") nodes are P nodes which have been given
certain B node characteristics. M nodes use both broadcast and
unicast. Broadcast is used to improve response time using the
assumption that most resources reside on the local broadcast medium
rather than somewhere in an internet.
M nodes rely upon NBNS and NBDD servers. However, M nodes may
continue limited operation should these servers be temporarily
unavailable.
NetBIOS Working Group [Page 17]
RFC 1001 March 1987
11. NetBIOS SUPPORT SERVERS
Two types of support servers are part of this standard:
- NetBIOS name server ("NBNS") nodes
- Netbios datagram distribution ("NBDD") nodes
NBNS and NBDD nodes are invisible to NetBIOS applications and are
part of the underlying NetBIOS mechanism.
NetBIOS name and datagram distribution servers are the focus of name
and datagram activity for P and M nodes.
Both the name (NBNS) and datagram distribution (NBDD) servers are
permitted to shift part of their operation to the P or M end-node
which is requesting a service.
Since the assignment of responsibility is dynamic, and since P and M
nodes must be prepared to operate should the NetBIOS server delegate
control to the maximum extent, the system naturally accommodates
improvements in NetBIOS server function. For example, as Internet
Group Multicasting becomes more widespread, new NBDD implementations
may elect to assume full responsibility for NetBIOS datagram
distribution.
Interoperability between different implementations is assured by
imposing requirements on end-node implementations that they be able
to accept the full range of legal responses from the NBNS or NBDD.
11.1. NetBIOS NAME SERVER (NBNS) NODES
The NBNS is designed to allow considerable flexibility with its
degree of responsibility for the accuracy and management of NetBIOS
names. On one hand, the NBNS may elect not to accept full
responsibility, leaving the NBNS essentially a "bulletin board" on
which name/address information is freely posted (and removed) by P
and M nodes without validation by the NBNS. Alternatively, the NBNS
may elect to completely manage and validate names. The degree of
responsibility that the NBNS assumes is asserted by the NBNS each
time a name is claimed through a simple mechanism. Should the NBNS
not assert full control, the NBNS returns enough information to the
requesting node so that the node may challenge any putative holder of
the name.
This ability to shift responsibility for NetBIOS name management
between the NBNS and the P and M nodes allows a network administrator
(or vendor) to make a tradeoff between NBNS simplicity, security, and
delay characteristics.
A single NBNS may be implemented as a distributed entity, such as the
Domain Name Service. However, this RFC does not attempt to define
NetBIOS Working Group [Page 18]
RFC 1001 March 1987
the internal communications which would be used.
11.1.1. RELATIONSHIP OF THE NBNS TO THE DOMAIN NAME SYSTEM
The NBNS design attempts to align itself with the Domain Name System
in a number of ways.
First, the NetBIOS names are encoded in a form acceptable to the
domain name system.
Second, a scope identifier is appended to each NetBIOS name. This
identifier meets the restricted character set of the domain system
and has a leading period. This makes the NetBIOS name, in
conjunction with its scope identifier, a valid domain system name.
Third, the negotiated responsibility mechanisms permit the NBNS to be
used as a simple bulletin board on which are posted (name,address)
pairs. This parallels the existing domain sytem query service.
This RFC, however, requires the NBNS to provide services beyond those
provided by the current domain name system. An attempt has been made
to coalesce all the additional services which are required into a set
of transactions which follow domain name system styles of interaction
and packet formats.
Among the areas in which the domain name service must be extended
before it may be used as an NBNS are:
- Dynamic addition of entries
- Dynamic update of entry data
- Support for multiple instance (group) entries
- Support for entry time-to-live values and ability to accept
refresh messages to restart the time-to-live period
- New entry attributes
11.2. NetBIOS DATAGRAM DISTRIBUTION SERVER (NBDD) NODES
The internet does not yet support broadcasting or multicasting. The
NBDD extends NetBIOS datagram distribution service to this
environment.
The NBDD may elect to complete, partially complete, or totally refuse
to service a node's request to distribute a NetBIOS datagram. An
end-node may query an NBDD to determine whether the NBDD will deliver
a datagram to a specific NetBIOS name.
The design of NetBIOS-over-TCP lends itself to the use of Internet
Group Multicast. For details see Appendix A.
NetBIOS Working Group [Page 19]
RFC 1001 March 1987
11.3. RELATIONSHIP OF NBNS AND NBDD NODES
This RFC defines the NBNS and NBDD as distinct, separate entities.
In the absence of NetBIOS name information, a NetBIOS datagram
distribution server must send a copy to each end-node within a
NetBIOS scope.
An implementer may elect to construct NBNS and NBDD nodes which have
a private protocol for the exchange of NetBIOS name information.
Alternatively, an NBNS and NBDD may be implemented within the same
device.
NOTE: Implementations containing private NBNS-NBDD protocols or
combined NBNS-NBDD functions must be clearly identified.
11.4. RELATIONSHIP OF NetBIOS SUPPORT SERVERS AND B NODES
As defined in this RFC, neither NBNS nor NBDD nodes interact with B
nodes. NetBIOS servers do not listen to broadcast traffic on any
broadcast area to which they may be attached. Nor are the NetBIOS
support servers even aware of B node activities or names claimed or
used by B nodes.
It may be possible to extend both the NBNS and NBDD so that they
participate in B node activities and act as a bridge to P and M
nodes. However, such extensions are beyond the scope of this
specification.
12. TOPOLOGIES
B, P, M, NBNS, and NBDD nodes may be combined in various ways to form
useful NetBIOS environments. This section describes some of these
combinations.
There are three classes of operation:
- Class 0: B nodes only.
- Class 1: P nodes only.
- Class 2: P and M nodes together.
In the drawings which follow, any P node may be replaced by an M
node. The effects of such replacement will be mentioned in
conjunction with each example below.
12.1. LOCAL
A NetBIOS scope is operating locally when all entities are within the
same broadcast area.
NetBIOS Working Group [Page 20]
RFC 1001 March 1987
12.1.1. B NODES ONLY
Local operation with only B nodes is the most basic mode of
operation. Name registration and discovery procedures use broadcast
mechanisms. The NetBIOS scope is limited by the extent of the
broadcast area. This configuration does not require NetBIOS support
servers.
====+=========+=====BROADCAST AREA=====+==========+=========+====
| | | | |
| | | | |
+--+--+ +--+--+ +--+--+ +--+--+ +--+--+
| B | | B | | B | | B | | B |
+-----+ +-----+ +-----+ +-----+ +-----+
12.1.2. P NODES ONLY
This configuration would typically be used when the network
administrator desires to eliminate NetBIOS as a source of broadcast
activity.
====+=========+==========+=B'CAST AREA=+==========+=========+====
| | | | | |
| | | | | |
+--+--+ +--+--+ +--+--+ +--+--+ +--+--+ +--+--+
| P | | P | |NBNS | | P | |NBDD | | P |
+-----+ +-----+ +-----+ +-----+ +-----+ +-----+
This configuration operates the same as if it were in an internet and
is cited here only due to its convenience as a means to reduce the
use of broadcast.
Replacement of one or more of the P nodes with M nodes will not
affect the operation of the other P and M nodes. P and M nodes will
be able to interact with one another. Because M nodes use broadcast,
overall broadcast activity will increase.
12.1.3. MIXED B AND P NODES
B and P nodes do not interact with one another. Replacement of P
nodes with M nodes will allow B's and M's to interact.
NOTE: B nodes and M nodes may be intermixed only on a local
broadcast area. B and M nodes should not be intermixed in
an internet environment.
NetBIOS Working Group [Page 21]
RFC 1001 March 1987
12.2. INTERNET
12.2.1. P NODES ONLY
P nodes may be scattered at various locations in an internetwork.
They require both an NBNS and an NBDD for NetBIOS name and datagram
support, respectively.
The NetBIOS scope is determined by the NetBIOS scope identifier
(domain name) used by the various P (and M) nodes. An internet may
contain numerous NetBIOS scopes.
+-----+
| P |
+--+--+ | +-----+
| |----+ P |
| | +-----+
/-----+-----\ |
+-----+ | | +------+ | +-----+
| P +------+ INTERNET +--+G'WAY |-+----+ P |
+-----+ | | +------+ | +-----+
/-----+-----/ |
/ | | +-----+
/ | |----+ P |
+-----+ +--+--+ | +-----+
|NBNS + |NBDD |
+-----+ +--+--+
Any P node may be replaced by an M node with no loss of function to
any node. However, broadcast activity will be increased in the
broadcast area to which the M node is attached.
NetBIOS Working Group [Page 22]
RFC 1001 March 1987
12.2.2. MIXED M AND P NODES
M and P nodes may be mixed. When locating NetBIOS names, M nodes
will tend to find names held by other M nodes on the same common
broadcast area in preference to names held by P nodes or M nodes
elsewhere in the network.
+-----+
| P |
+--+--+
|
|
/-----+-----\
+-----+ | | +-----+
| P +------+ INTERNET +------+NBDD |
+-----+ | | +-----+
/-----+-----/
/ |
/ |
+-----+ +--+--+
|NBNS + |G'WAY|
+-----+ +--+--+
|
|
====+=========+==========+=B'CAST AREA=+==========+=========+====
| | | | | |
| | | | | |
+--+--+ +--+--+ +--+--+ +--+--+ +--+--+ +--+--+
| M | | P | | M | | P | | M | | P |
+-----+ +-----+ +--+--+ +-----+ +-----+ +-----+
NOTE: B and M nodes should not be intermixed in an internet
environment. Doing so would allow undetected NetBIOS name
conflicts to arise and cause unpredictable behavior.
13. GENERAL METHODS
Overlying the specific protocols, described later, are a few general
methods of interaction between entities.
13.1. REQUEST/RESPONSE INTERACTION STYLE
Most interactions between entities consist of a request flowing in
one direction and a subsequent response flowing in the opposite
direction.
In those situations where interactions occur on unreliable transports
(i.e. UDP) or when a request is broadcast, there may not be a strict
interlocking or one-to-one relationship between requests and
responses.
NetBIOS Working Group [Page 23]
RFC 1001 March 1987
In no case, however, is more than one response generated for a
received request. While a response is pending the responding entity
may send one or more wait acknowledgements.
13.1.1. RETRANSMISSION OF REQUESTS
UDP is an unreliable delivery mechanism where packets can be lost,
received out of transmit sequence, duplicated and delivery can be
significantly delayed. Since the NetBIOS protocols make heavy use of
UDP, they have compensated for its unreliability with extra
mechanisms.
Each NetBIOS packet contains all the necessary information to process
it. None of the protocols use multiple UDP packets to convey a
single request or response. If more information is required than
will fit in a single UDP packet, for example, when a P-type node
wants all the owners of a group name from a NetBIOS server, a TCP
connection is used. Consequently, the NetBIOS protocols will not
fail because of out of sequence delivery of UDP packets.
To overcome the loss of a request or response packet, each request
operation will retransmit the request if a response is not received
within a specified time limit.
Protocol operations sensitive to successive response packets, such as
name conflict detection, are protected from duplicated packets
because they ignore successive packets with the same NetBIOS
information. Since no state on the responder's node is associated
with a request, the responder just sends the appropriate response
whenever a request packet arrives. Consequently, duplicate or
delayed request packets have no impact.
For all requests, if a response packet is delayed too long another
request packet will be transmitted. A second response packet being
sent in response to the second request packet is equivalent to a
duplicate packet. Therefore, the protocols will ignore the second
packet received. If the delivery of a response is delayed until
after the request operation has been completed, successfully or not,
the response packet is ignored.
13.1.2. REQUESTS WITHOUT RESPONSES: DEMANDS
Some request types do not have matching responses. These requests
are known as "demands". In general a "demand" is an imperative
request; the receiving node is expected to obey. However, because
demands are unconfirmed, they are used only in situations where, at
most, limited damage would occur if the demand packet should be lost.
Demand packets are not retransmitted.
NetBIOS Working Group [Page 24]
RFC 1001 March 1987
13.2. TRANSACTIONS
Interactions between a pair of entities are grouped into
"transactions". These transactions comprise one or more
request/response pairs.
13.2.1. TRANSACTION ID
Since multiple simultaneous transactions may be in progress between a
pair of entities a "transaction id" is used.
The originator of a transaction selects an ID unique to the
originator. The transaction id is reflected back and forth in each
interaction within the transaction. The transaction partners must
match responses and requests by comparison of the transaction ID and
the IP address of the transaction partner. If no matching request
can be found the response must be discarded.
A new transaction ID should be used for each transaction. A simple
16 bit transaction counter ought to be an adequate id generator. It
is probably not necessary to search the space of outstanding
transaction ID to filter duplicates: it is extremely unlikely that
any transaction will have a lifetime that is more than a small
fraction of the typical counter cycle period. Use of the IP
addresses in conjunction with the transaction ID further reduces the
possibility of damage should transaction IDs be prematurely re-used.
13.3. TCP AND UDP FOUNDATIONS
This version of the NetBIOS-over-TCP protocols uses UDP for many
interactions. In the future this RFC may be extended to permit such
interactions to occur over TCP connections (perhaps to increase
efficiency when multiple interactions occur within a short time or
when NetBIOS datagram traffic reveals that an application is using
NetBIOS datagrams to support connection- oriented service.)
14. REPRESENTATION OF NETBIOS NAMES
NetBIOS names as seen across the client interface to NetBIOS are
exactly 16 bytes long. Within the NetBIOS-over-TCP protocols, a
longer representation is used.
There are two levels of encoding. The first level maps a NetBIOS
name into a domain system name. The second level maps the domain
system name into the "compressed" representation required for
interaction with the domain name system.
Except in one packet, the second level representation is the only
NetBIOS name representation used in NetBIOS-over-TCP packet formats.
The exception is the RDATA field of a NODE STATUS RESPONSE packet.
NetBIOS Working Group [Page 25]
RFC 1001 March 1987
14.1. FIRST LEVEL ENCODING
The first level representation consists of two parts:
- NetBIOS name
- NetBIOS scope identifier
The 16 byte NetBIOS name is mapped into a 32 byte wide field using a
reversible, half-ASCII, biased encoding. Each half-octet of the
NetBIOS name is encoded into one byte of the 32 byte field. The
first half octet is encoded into the first byte, the second half-
octet into the second byte, etc.
Each 4-bit, half-octet of the NetBIOS name is treated as an 8-bit,
right-adjusted, zero-filled binary number. This number is added to
value of the ASCII character 'A' (hexidecimal 41). The resulting 8-
bit number is stored in the appropriate byte. The following diagram
demonstrates this procedure:
0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+
|a b c d|w x y z| ORIGINAL BYTE
+-+-+-+-+-+-+-+-+
| |
+--------+ +--------+
| | SPLIT THE NIBBLES
v v
0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+
|0 0 0 0 a b c d| |0 0 0 0 w x y z|
+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+
| |
+ + ADD 'A'
| |
0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7
+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+
|0 1 0 0 0 0 0 1| |0 1 0 0 0 0 0 1|
+-+-+-+-+-+-+-+-+ +-+-+-+-+-+-+-+-+
This encoding results in a NetBIOS name being represented as a
sequence of 32 ASCII, upper-case characters from the set
{A,B,C...N,O,P}.
The NetBIOS scope identifier is a valid domain name (without a
leading dot).
An ASCII dot (2E hexidecimal) and the scope identifier are appended
to the encoded form of the NetBIOS name, the result forming a valid
domain name.
NetBIOS Working Group [Page 26]
RFC 1001 March 1987
For example, the NetBIOS name "The NetBIOS name" in the NetBIOS scope
"SCOPE.ID.COM" would be represented at level one by the ASCII
character string:
FEGHGFCAEOGFHEECEJEPFDCAHEGBGNGF.SCOPE.ID.COM
14.2. SECOND LEVEL ENCODING
The first level encoding must be reduced to second level encoding.
This is performed according to the rules defined in on page 31 of RFC
883[12] in the section on "Domain name representation and
compression". Also see the section titled "Name Formats" in the
Detailed Specifications[1].
15. NetBIOS NAME SERVICE
Before a name may be used, the name must be registered by a node.
Once acquired, the name must be defended against inconsistent
registration by other nodes. Before building a NetBIOS session or
sending a NetBIOS datagram, the one or more holders of the name must
be located.
The NetBIOS name service is the collection of procedures through
which nodes acquire, defend, and locate the holders of NetBIOS names.
The name service procedures are different depending whether the end-
node is of type B, P, or M.
15.1. OVERVIEW OF NetBIOS NAME SERVICE
15.1.1. NAME REGISTRATION (CLAIM)
Each NetBIOS node can own more than one name. Names are acquired
dynamically through the registration (name claim) procedures.
Every node has a permanent unique name. This name, like any other
name, must be explicitly registered by all end-node types.
A name can be unique (exclusive) or group (non-exclusive). A unique
name may be owned by a single node; a group name may be owned by any
number of nodes. A name ceases to exist when it is not owned by at
least one node. There is no intrinsic quality of a name which
determines its characteristics: these are established at the time of
registration.
Each node maintains state information for each name it has
registered. This information includes:
- Whether the name is a group or unique name
- Whether the name is "in conflict"
- Whether the name is in the process of being deleted
NetBIOS Working Group [Page 27]
RFC 1001 March 1987
B nodes perform name registration by broadcasting claim requests,
soliciting a defense from any node already holding the name.
P nodes perform name registration through the agency of the NBNS.
M nodes register names through an initial broadcast, like B nodes,
then, in the absence of an objection, by following the same
procedures as a P node. In other words, the broadcast action may
terminate the attempt, but is not sufficient to confirm the
registration.
15.1.2. NAME QUERY (DISCOVERY)
Name query (also known as "resolution" or "discovery") is the
procedure by which the IP address(es) associated with a NetBIOS name
are discovered. Name query is required during the following
operations:
During session establishment, calling and called names must be
specified. The calling name must exist on the node that posts the
CALL. The called name must exist on a node that has previously
posted a LISTEN. Either name may be a unique or group name.
When a directed datagram is sent, a source and destination name must
be specified. If the destination name is a group name, a datagram is
sent to all the members of that group.
Different end-node types perform name resolution using different
techniques, but using the same packet formats:
- B nodes solicit name information by broadcasting a request.
- P nodes ask the NBNS.
- M nodes broadcast a request. If that does not provide the
desired information, an inquiry is sent to the NBNS.
15.1.3. NAME RELEASE
NetBIOS names may be released explicitly or silently by an end- node.
Silent release typically occurs when an end-node fails or is turned-
off. Most of the mechanisms described below are present to detect
silent name release.
15.1.3.1. EXPLICIT RELEASE
B nodes explicitly release a name by broadcasting a notice.
P nodes send a notification to their NBNS.
M nodes both broadcast a notice and inform their supporting NBNS.
NetBIOS Working Group [Page 28]
RFC 1001 March 1987
15.1.3.2. NAME LIFETIME AND REFRESH
Names held by an NBNS are given a lifetime during name registration.
The NBNS will consider a name to have been silently released if the
end-node fails to send a name refresh message to the NBNS before the
lifetime expires. A refresh restarts the lifetime clock.
NOTE: The implementor should be aware of the tradeoff between
accuracy of the database and the internet overhead that the
refresh mechanism introduces. The lifetime period should
be tuned accordingly.
For group names, each end-node must send refresh messages. A node
that fails to do so will be considered to have silently released the
name and dropped from the group.
The lifetime period is established through a simple negotiation
mechanism during name registration: In the name registration
request, the end-node proposes a lifetime value or requests an
infinite lifetime. The NBNS places an actual lifetime value into the
name registration response. The NBNS is always allowed to respond
with an infinite actual period. If the end node proposed an infinite
lifetime, the NBNS may respond with any definite period. If the end
node proposed a definite period, the NBNS may respond with any
definite period greater than or equal to that proposed.
This negotiation of refresh times gives the NBNS means to disable or
enable refresh activity. The end-nodes may set a minimum refresh
cycle period.
NBNS implementations which are completely reliable may disable
refresh.
15.1.3.3. NAME CHALLENGE
To detect whether a node has silently released its claim to a name,
it is necessary on occasion to challenge that node's current
ownership. If the node defends the name then the node is allowed to
continue possession. Otherwise it is assumed that the node has
released the name.
A name challenge may be issued by an NBNS or by a P or M node. A
challenge may be directed towards any end-node type: B, P, or M.
15.1.3.4. GROUP NAME FADE-OUT
NetBIOS groups may contain an arbitrarily large number of members.
The time to challenge all members could be quite large.
To avoid long delays when names are claimed through an NBNS, an
NetBIOS Working Group [Page 29]
RFC 1001 March 1987
optimistic heuristic has been adopted. It is assumed that there will
always be some node which will defend a group name. Consequently, it
is recommended that the NBNS will immediately reject a claim request
for a unique name when there already exists a group with the same
name. The NBNS will never return an IP address (in response to a
NAME REGISTRATION REQUEST) when a group name exists.
An NBNS will consider a group to have faded out of existence when the
last remaining member fails to send a timely refresh message or
explicitly releases the name.
15.1.3.5. NAME CONFLICT
Name conflict exists when a unique name has been claimed by more than
one node on a NetBIOS network. B, M, and NBNS nodes may detect a
name conflict. The detection mechanism used by B and M nodes is
active only during name discovery. The NBNS may detect conflict at
any time it verifies the consistency of its name database.
B and M nodes detect conflict by examining the responses received in
answer to a broadcast name query request. The first response is
taken as authoritative. Any subsequent, inconsistent responses
represent conflicts.
Subsequent responses are inconsistent with the authoritative response
when:
The subsequent response has the same transaction ID as the
NAME QUERY REQUEST.
AND
The subsequent response is not a duplicate of the
authoritative response.
AND EITHER:
The group/unique characteristic of the authoritative
response is "unique".
OR
The group/unique characteristic of the subsequent
response is "unique".
The period in which B and M nodes examine responses is limited by a
conflict timer, CONFLICT_TIMER. The accuracy or duration of this
timer is not crucial: the NetBIOS system will continue to operate
even with persistent name conflicts.
Conflict conditions are signaled by sending a NAME CONFLICT DEMAND to
the node owning the offending name. Nothing is sent to the node
which originated the authoritative response.
Any end-node that receives NAME CONFLICT DEMAND is required to update
its "local name table" to reflect that the name is in conflict. (The
"local name table" on each node contains names that have been
NetBIOS Working Group [Page 30]
RFC 1001 March 1987
successfully registered by that node.)
Notice that only those nodes that receive the name conflict message
place a conflict mark next to a name.
Logically, a marked name does not exist on that node. This means
that the node should not defend the name (for name claim purposes),
should not respond to a name discovery requests for that name, nor
should the node send name refresh messages for that name.
Furthermore, it can no longer be used by that node for any session
establishment or sending or receiving datagrams. Existing sessions
are not affected at the time a name is marked as being in conflict.
The only valid user function against a marked name is DELETE NAME.
Any other user NetBIOS function returns immediately with an error
code of "NAME CONFLICT".
15.1.4. ADAPTER STATUS
An end-node or the NBNS may ask any other end-node for a collection
of information about the NetBIOS status of that node. This status
consists of, among other things, a list of the names which the node
believes it owns. The returned status is filtered to contain only
those names which have the same NetBIOS scope identifier as the
requestor's name.
When requesting node status, the requestor identifies the target node
by NetBIOS name A name query transaction may be necessary to acquire
the IP address for the name. Locally cached name information may be
used in lieu of a query transaction. The requesting node sends a
NODE STATUS REQUEST. In response, the receiving node sends a NODE
STATUS RESPONSE containing its local name table and various
statistics.
The amount of status which may be returned is limited by the size of
a UDP packet. However, this is sufficient for the typical NODE
STATUS RESPONSE packet.
15.1.5. END-NODE NBNS INTERACTION
There are certain characteristics of end-node to NBNS interactions
which are in common and are independent of any particular transaction
type.
15.1.5.1. UDP, TCP, AND TRUNCATION
For all transactions between an end-node and an NBNS, either UDP or
TCP may be used as a transport. If the NBNS receives a UDP based
request, it will respond using UDP. If the amount of information
exceeds what fits into a UDP packet, the response will contain a
"truncation flag". In this situation, the end- node may open a TCP
NetBIOS Working Group [Page 31]
RFC 1001 March 1987
connection to the NBNS, repeat the request, and receive a complete,
untruncated response.
15.1.5.2. NBNS WACK
While a name service request is in progress, the NBNS may issue a
WAIT FOR ACKNOWLEDGEMENT RESPONSE (WACK) to assure the client end-
node that the NBNS is still operational and is working on the
request.
15.1.5.3. NBNS REDIRECTION
The NBNS, because it follows Domain Name system styles of
interaction, is permitted to redirect a client to another NBNS.
15.1.6. SECURED VERSUS NON-SECURED NBNS
An NBNS may be implemented in either of two general ways: The NBNS
may monitor, and participate in, name activity to ensure consistency.
This would be a "secured" style NBNS. Alternatively, an NBNS may be
implemented to be essentially a "bulletin board" on which name
information is posted and responsibility for consistency is delegated
to the end-nodes. This would be a "non-secured" style NBNS.
15.1.7. CONSISTENCY OF THE NBNS DATA BASE
Even in a properly running NetBIOS scope the NBNS and its community
of end-nodes may occasionally lose synchronization with respect to
the true state of name registrations.
This may occur should the NBNS fail and lose all or part of its
database.
More commonly, a P or M node may be turned-off (thus forgetting the
names it has registered) and then be subsequently turned back on.
Finally, errors may occur or an implementation may be incorrect.
Various approaches have been incorporated into the NetBIOS-over- TCP
protocols to minimize the impact of these problems.
1. The NBNS (or any other node) may "challenge" (using a NAME
QUERY REQUEST) an end-node to verify that it actually owns a
name.
Such a challenge may occur at any time. Every end-node must
be prepared to make a timely response.
Failure to respond causes the NBNS to consider that the
end-node has released the name in question.
NetBIOS Working Group [Page 32]
RFC 1001 March 1987
(If UDP is being used as the underlying transport, the
challenge, like all other requests, must be retransmitted
some number of times in the absence of a response.)
2. The NBNS (or any other node) may request (using the NODE
STATUS REQUEST) that an end-node deliver its entire name
table.
This may occur at any time. Every end-node must be prepared
to make a timely response.
Failure to respond permits (but does not require) the NBNS
to consider that the end-node has failed and released all
names to which it had claims. (Like the challenge, on a UDP
transport, the request must be retransmitted in the absence
of a response.)
3. The NBNS may revoke a P or M node's use of a name by sending
either a NAME CONFLICT DEMAND or a NAME RELEASE REQUEST to
the node.
The receiving end-node may continue existing sessions which
use that name, but must otherwise cease using that name. If
the NBNS placed the name in conflict, the name may be re-
acquired only by deletion and subsequent reclamation. If
the NBNS requested that the name be released, the node may
attempt to re-acquire the name without first performing a
name release transaction.
4. The NBNS may impose a "time-to-live" on each name it
registers. The registering node is made aware of this time
value during the name registration procedure.
Simple or reliable NBNS's may impose an infinite time-to-
live.
5. If an end-node holds any names that have finite time-to-
live values, then that node must periodically send a status
report to the NBNS. Each name is reported using the NAME
REFRESH REQUEST packet.
These status reports restart the timers of both the NBNS and
the reporting node. However, the only timers which are
restarted are those associated with the name found in the
status report. Timers on other names are not affected.
The NBNS may consider that a node has released any name
which has not been refreshed within some multiple of name's
time-to-live.
A well-behaved NBNS, would, however, issue a challenge to-,
NetBIOS Working Group [Page 33]
RFC 1001 March 1987
or request a list of names from-, the non-reporting end-
node before deleting its name(s). The absence of a
response, or of the name in a response, will confirm the
NBNS decision to delete a name.
6. The absence of reports may cause the NBNS to infer that the
end-node has failed. Similarly, receipt of information
widely divergent from what the NBNS believes about the node,
may cause the NBNS to consider that the end-node has been
restarted.
The NBNS may analyze the situation through challenges or
requests for a list of names.
7. A very cautious NBNS is free to poll nodes (by sending NAME
QUERY REQUEST or NODE STATUS REQUEST packets) to verify that
their name status is the same as that registered in the
NBNS.
NOTE: Such polling activity, if used at all by an
implementation, should be kept at a very low level or
enabled only during periods when the NBNS has some reason to
suspect that its information base is inaccurate.
8. P and M nodes can detect incorrect name information at
session establishment.
If incorrect information is found, NBNS is informed via a
NAME RELEASE REQUEST originated by the end-node which
detects the error.
15.1.8. NAME CACHING
An end-node may keep a local cache of NetBIOS name-to-IP address
translation entries.
All cache entries should be flushed on a periodic basis.
In addition, a node ought to flush any cache information associated
with an IP address if the node receives any information indicating
that there may be any possibility of trouble with the node at that IP
address. For example, if a NAME CONFLICT DEMAND is sent to a node,
all cached information about that node should be cleared within the
sending node.
15.2. NAME REGISTRATION TRANSACTIONS
15.2.1. NAME REGISTRATION BY B NODES
A name claim transaction initiated by a B node is broadcast
throughout the broadcast area. The NAME REGISTRATION REQUEST will be
NetBIOS Working Group [Page 34]
RFC 1001 March 1987
heard by all B and M nodes in the area. Each node examines the claim
to see whether it it is consistent with the names it owns. If an
inconsistency exists, a NEGATIVE NAME REGISTRATION RESPONSE is
unicast to the requestor. The requesting node obtains ownership of
the name (or membership in the group) if, and only if, no NEGATIVE
NAME REGISTRATION RESPONSEs are received within the name claim
timeout, CONFLICT_TIMER. (See "Defined Constants and Variables" in
the Detailed Specification for the value of this timer.)
A B node proclaims its new ownership by broadcasting a NAME OVERWRITE
DEMAND.
B-NODE REGISTRATION PROCESS
<-----NAME NOT ON NETWORK------> <----NAME ALREADY EXISTS---->
REQ. NODE NODE REQ.NODE
HOLDING
NAME
(BROADCAST) REGISTER (BROADCAST) REGISTER
-------------------> <-------------------
REGISTER REGISTER
-------------------> <-------------------
REGISTER NEGATIVE RESPONSE
-------------------> ------------------------------>
OVERWRITE
-------------------> (NODE DOES NOT HAVE THE NAME)
(NODE HAS THE NAME)
The NAME REGISTRATION REQUEST, like any request, must be repeated if
no response is received within BCAST_REQ_RETRY_TIMEOUT. Transmission
of the request is attempted BCAST_REQ_RETRY_COUNT times.
15.2.2. NAME REGISTRATION BY P NODES
A name registration may proceed in various ways depending whether
the name being registered is new to the NBNS. If the name is known
to the NBNS, then challenges may be sent to the prior holder(s).
15.2.2.1. NEW NAME, OR NEW GROUP MEMBER
The diagram, below, shows the sequence of events when an end-node
registers a name which is new to the NBNS. (The diagram omits WACKs,
NBNS redirections, and retransmission of requests.)
This same interaction will occur if the name being registered is a
group name and the group already exists. The NBNS will add the
NetBIOS Working Group [Page 35]
RFC 1001 March 1987
registrant to the set of group members.
P-NODE REGISTRATION PROCESS
(server has no previous information about the name)
P-NODE NBNS
REGISTER
--------------------------------->
POSITIVE RESPONSE
<---------------------------------
The interaction is rather simple: the end-node sends a NAME
REGISTRATION REQUEST, the NBNS responds with a POSITIVE NAME
REGISTRATION RESPONSE.
15.2.2.2. EXISTING NAME AND OWNER IS STILL ACTIVE
The following diagram shows interactions when an attempt is made to
register a unique name, the NBNS is aware of an existing owner, and
that existing owner is still active.
There are two sides to the diagram. The left side shows how a non-
secured NBNS would handle the matter. Secured NBNS activity is shown
on the right.
P-NODE REGISTRATION PROCESS
(server HAS a previous owner that IS active)
<------NON-SECURED STYLE-------> <---------SECURED STYLE------->
REQ. NODE NBNS NODE NBNS REQ.NODE
HOLDING
NAME
REGISTER REGISTER
-------------------> <-------------------
QUERY
END-NODE CHALLENGE <------------
<------------------- QUERY
<------------
QUERY
----------------------------->
POSITIVE RESP
QUERY ------------>
-----------------------------> NEGATIVE RESPONSE
----------------->
POSITIVE RESPONSE
<----------------------------
NetBIOS Working Group [Page 36]
RFC 1001 March 1987
A non-secured NBNS will answer the NAME REGISTRATION REQUEST with a
END-NODE CHALLENGE REGISTRATION RESPONSE. This response asks the
end-node to issue a challenge transaction against the node indicated
in the response. In this case, the prior node will defend against
the challenge and the registering end-node will simply drop the
registration attempt without further interaction with the NBNS.
A secured NBNS will refrain from answering the NAME REGISTRATION
REQUEST until the NBNS has itself challenged the prior holder(s) of
the name. In this case, the NBNS finds that that the name is still
being defended and consequently returns a NEGATIVE NAME REGISTRATION
RESPONSE to the registrant.
Due to the potential time for the secured NBNS to make the
challenge(s), it is likely that a WACK will be sent by the NBNS to
the registrant.
Although not shown in the diagram, a non-secured NBNS will send a
NEGATIVE NAME REGISTRATION RESPONSE to a request to register a unique
name when there already exists a group of the same name. A secured
NBNS may elect to poll (or challenge) the group members to determine
whether any active members remain. This may impose a heavy load on
the network. It is recommended that group names be allowed to fade-
out through the name refresh mechanism.
15.2.2.3. EXISTING NAME AND OWNER IS INACTIVE
The following diagram shows interactions when an attempt is made to
register a unique name, the NBNS is aware of an existing owner, and
that existing owner is no longer active.
A non-secured NBNS will answer the NAME REGISTRATION REQUEST with a
END-NODE CHALLENGE REGISTRATION RESPONSE. This response asks the
end-node to issue a challenge transaction against the node indicated
in the response. In this case, the prior node will not defend
against the challenge. The registrant will inform the NBNS through a
NAME OVERWRITE REQUEST. The NBNS will replace the prior name
information in its database with the information in the overwrite
request.
A secured NBNS will refrain from answering the NAME REGISTRATION
REQUEST until the NBNS has itself challenged the prior holder(s) of
the name. In this case, the NBNS finds that that the name is not
being defended and consequently returns a POSITIVE NAME REGISTRATION
RESPONSE to the registrant.
NetBIOS Working Group [Page 37]
RFC 1001 March 1987
P-NODE REGISTRATION PROCESS
(server HAS a previous owner that is NOT active)
<------NON-SECURED STYLE-----> <----------SECURED STYLE-------->
REQ. NODE NBNS NODE NBNS REQ.NODE
HOLDING
NAME
REGISTER REGISTER
-------------------> <-------------------
QUERY
END-NODE CHALLENGE <------------
<------------------- QUERY
<------------
NAME QUERY REQUEST POSITIVE RESPONSE
----------------------------> ------------------>
QUERY
---------------------------->
OVERWRITE
------------------->
POSITIVE RESPONSE
<------------------
Due to the potential time for the secured NBNS to make the
challenge(s), it is likely that a WACK will be sent by the NBNS to
the registrant.
A secured NBNS will immediately send a NEGATIVE NAME REGISTRATION
RESPONSE in answer to any NAME OVERWRITE REQUESTS it may receive.
15.2.3. NAME REGISTRATION BY M NODES
An M node begin a name claim operation as if the node were a B node:
it broadcasts a NAME REGISTRATION REQUEST and listens for NEGATIVE
NAME REGISTRATION RESPONSEs. Any NEGATIVE NAME REGISTRATION RESPONSE
prevents the M node from obtaining the name and terminates the claim
operation.
If, however, the M node does not receive any NEGATIVE NAME
REGISTRATION RESPONSE, the M node must continue the claim procedure
as if the M node were a P node.
Only if both name claims were successful does the M node acquire the
name.
The following diagram illustrates M node name registration:
NetBIOS Working Group [Page 38]
RFC 1001 March 1987
M-NODE REGISTRATION PROCESS
<---NAME NOT IN BROADCAST AREA--> <--NAME IS IN BROADCAST AREA-->
REQ. NODE NODE REQ.NODE
HOLDING
NAME
(BROADCAST) REGISTER (BROADCAST) REGISTER
-------------------> <-------------------
REGISTER REGISTER
-------------------> <-------------------
REGISTER NEGATIVE RESPONSE
-------------------> ------------------------------->
! (NODE DOES NOT HAVE THE NAME)
INITIATE !
A P-NODE !
REGISTRATION !
V
15.3. NAME QUERY TRANSACTIONS
Name query transactions are initiated by end-nodes to obtain the IP
address(es) and other attributes associated with a NetBIOS name.
15.3.1. QUERY BY B NODES
The following diagram shows how B nodes go about discovering who owns
a name.
The left half of the diagram illustrates what happens if there are no
holders of the name. In that case no responses are received in
answer to the broadcast NAME QUERY REQUEST(s).
The right half shows a POSITIVE NAME QUERY RESPONSE unicast by a name
holder in answer to the broadcast request. A name holder will make
this response to every NAME QUERY REQUEST that it hears. And each
holder acts this way. Thus, the node sending the request may receive
many responses, some duplicates, and from many nodes.
NetBIOS Working Group [Page 39]
RFC 1001 March 1987
B-NODE DISCOVERY PROCESS
<------NAME NOT ON NETWORK------> <---NAME PRESENT ON NETWORK-->
REQ. NODE NODE REQ.NODE
HOLDING
NAME
(BROADCAST) QUERY (BROADCAST) QUERY
----------------------> <---------------------
NAME QUERY REQUEST NAME QUERY REQUEST
----------------------> <---------------------
QUERY POSITIVE RESPONSE
----------------------> ------------------------------>
Name query is generally, but not necessarily, a prelude to NetBIOS
session establishment or NetBIOS datagram transmission. However,
name query may be used for other purposes.
A B node may elect to build a group membership list for subsequent
use (e.g. for session establishment) by collecting and saving the
responses.
15.3.2. QUERY BY P NODES
An NBNS answers queries from a P node with a list of IP address and
other information for each owner of the name. If there are multiple
owners (i.e. if the name is a group name), the NBNS loads as many
answers into the response as will fit into a UDP packet. A
truncation flag indicates whether any additional owner information
remains. All the information may be obtained by repeating the query
over a TCP connection.
The NBNS is not required to impose any order on its answer list.
The following diagram shows what happens if the NBNS has no
information about the name:
P-NODE DISCOVERY PROCESS
(server has no information about the name)
P-NODE NBNS
NAME QUERY REQUEST
--------------------------------->
NEGATIVE RESPONSE
<---------------------------------
NetBIOS Working Group [Page 40]
RFC 1001 March 1987
The next diagram illustrates interaction between the end-node and the
NBNS when the NBNS does have information about the name. This
diagram shows, in addition, the retransmission of the request by the
end-node in the absence of a timely response. Also shown are WACKs
(or temporary, intermediate responses) sent by the NBNS to the end-
node:
P-NODE QUERY PROCESS
(server HAS information about the name)
P-NODE NBNS
NAME QUERY REQUEST
/---------------------------------------->
/
! (OPTIONAL) WACK
! <- - - - - - - - - - - - - - - - - - - -
! !
!timer !
! ! (optional timer restart)
! !
\ V QUERY
\--------------------------------------->
.
.
.
QUERY
/---------------------------------------->
/
! (OPTIONAL) WACK
! <- - - - - - - - - - - - - - - - - - - -
! !
!timer !
! ! (optional timer restart)
! !
\ V QUERY
\--------------------------------------->
.
.
POSITIVE RESPONSE
<-----------------------------------------
The following diagram illustrates NBNS redirection. Upon receipt of
a NAME QUERY REQUEST, the NBNS redirects the client to another NBNS.
The client repeats the request to the new NBNS and obtains a
response. The diagram shows that response as a POSITIVE NAME QUERY
RESPONSE. However any legal NBNS response may occur in actual
operation.
NetBIOS Working Group [Page 41]
RFC 1001 March 1987
NBNS REDIRECTION
P-NODE NBNS
NAME QUERY REQUEST
--------------------------------->
REDIRECT NAME QUERY RESPONSE
<---------------------------------
(START FROM THE
VERY BEGINNING
USING THE ADDRESS
OF THE NEWLY
SUPPLIED NBNS.)
NEW
P-NODE NBNS
NAME QUERY REQUEST
--------------------------------->
POSITIVE NAME QUERY RESPONSE
<---------------------------------
The next diagram shows how a P or M node tells the NBNS that the NBNS
has provided incorrect information. This procedure may begin after a
DATAGRAM ERROR packet has been received or a session set-up attempt
has discovered that the NetBIOS name does not exist at the
destination, the IP address of which was obtained from the NBNS
during a prior name query transaction. The NBNS, in this case a
secure NBNS, issues queries to verify whether the information is, in
fact, incorrect. The NBNS closes the transaction by sending either a
POSITIVE or NEGATIVE NAME RELEASE RESPONSE, depending on the results
of the verification.
CORRECTING NBNS INFORMATION BASE
P-NODE NBNS
NAME RELEASE REQUEST
--------------------------------->
QUERY
---------------->
QUERY
---------------->
(NAME TAKEN OFF THE DATABASE
IF NBNS FINDS IT TO BE
INCORRECT)
POSITIVE/NEGATIVE RESPONSE
<---------------------------------
NetBIOS Working Group [Page 42]
RFC 1001 March 1987
15.3.3. QUERY BY M NODES
M node name query follows the B node pattern. In the absence of
adequate results, the M node then continues by performing a P node
type query. This is shown in the following diagram:
M-NODE DISCOVERY PROCESS
<---NAME NOT ON BROADCAST AREA--> <--NAME IS ON BROADCAST AREA->
REQ. NODE NODE REQ.NODE
HOLDING
NAME
(BROADCAST) QUERY (BROADCAST) QUERY
---------------------> <----------------------
NAME QUERY REQUEST NAME QUERY REQUEST
---------------------> <----------------------
QUERY POSITIVE RESPONSE
---------------------> ------------------------------->
!
INITIATE !
A P-NODE !
DISCOVERY !
PROCESS !
V
15.3.4. ACQUIRE GROUP MEMBERSHIP LIST
The entire membership of a group may be acquired by sending a NAME
QUERY REQUEST to the NBNS. The NBNS will respond with a POSITIVE
NAME QUERY RESPONSE or a NEGATIVE NAME QUERY RESPONSE. A negative
response completes the procedure and indicates that there are no
members in the group.
If the positive response has the truncation bit clear, then the
response contains the entire list of group members. If the
truncation bit is set, then this entire procedure must be repeated,
but using TCP as a foundation rather than UDP.
NetBIOS Working Group [Page 43]
RFC 1001 March 1987
15.4. NAME RELEASE TRANSACTIONS
15.4.1. RELEASE BY B NODES
A NAME RELEASE DEMAND contains the following information:
- NetBIOS name
- The scope of the NetBIOS name
- Name type: unique or group
- IP address of the releasing node
- Transaction ID
REQUESTING OTHER
B-NODE B-NODES
NAME RELEASE DEMAND
---------------------------------->
15.4.2. RELEASE BY P NODES
A NAME RELEASE REQUEST contains the following information:
- NetBIOS name
- The scope of the NetBIOS name
- Name type: unique or group
- IP address of the releasing node
- Transaction ID
A NAME RELEASE RESPONSE contains the following information:
- NetBIOS name
- The scope of the NetBIOS name
- Name type: unique or group
- IP address of the releasing node
- Transaction ID
- Result:
- Yes: name was released
- No: name was not released, a reason code is provided
REQUESTING
P-NODE NBNS
NAME RELEASE REQUEST
---------------------------------->
NAME RELEASE RESPONSE
<---------------------------------
15.4.3. RELEASE BY M NODES
The name release procedure of the M node is a combination of the P
and B node name release procedures. The M node first performs the P
NetBIOS Working Group [Page 44]
RFC 1001 March 1987
release procedure. If the P procedure fails then the release
procedure does not continue, it fails. If and only if the P
procedure succeeds then the M node broadcasts the NAME RELEASE DEMAND
to the broadcast area, the B procedure.
NOTE: An M node typically performs a B-style operation and then a
P-style operation. In this case, however, the P-style
operation comes first.
The following diagram illustrates the M node name release procedure:
<-----P procedure fails-------> <-------P procedure succeeds--->
REQUESTING NBNS REQUESTING NBNS
M-NODE M-NODE
NAME RELEASE REQUEST NAME RELEASE REQUEST
--------------------------> ------------------------>
NEGATIVE RELEASE RESPONSE POSITIVE RELEASE RESPONSE
<-------------------------- <-------------------------
OTHER
M-NODES
NAME RELEASE DEMAND
------------------------>
15.5. NAME MAINTENANCE TRANSACTIONS
15.5.1. NAME REFRESH
Name refresh transactions are used to handle the following
situations:
a) An NBNS node needs to detect if a P or M node has "silently"
gone down, so that names held by that node can be purged
from the data base.
b) If the NBNS goes down, it needs to be able to reconstruct
the data base when it comes back up.
c) If the network should be partitioned, the NBNS needs to be
able to able to update its data base when the network
reconnects.
Each P or M node is responsible for sending periodic NAME REFRESH
REQUESTs for each name that it has registered. Each refresh packet
contains a single name that has been successfully registered by that
NetBIOS Working Group [Page 45]
RFC 1001 March 1987
node. The interval between such packets is negotiated between the
end node and the NBNS server at the time that the name is initially
claimed. At name claim time, an end node will suggest a refresh
timeout value. The NBNS node can modify this value in the reply
packet. A NBNS node can also choose to tell the end node to not send
any refresh packet by using the "infinite" timeout value in the
response packet. The timeout value returned by the NBNS is the
actual refresh timeout that the end node must use.
When a node sends a NAME REFRESH REQUEST, it must be prepared to
receive a negative response. This would happen, for example, if the
the NBNS discovers that the the name had already been assigned to
some other node. If such a response is received, the end node should
mark the name as being in conflict. Such an entry should be treated
in the same way as if name conflict had been detected against the
name. The following diagram illustrates name refresh:
<-----Successful Refresh-----> <-----Unsuccessful Refresh---->
REFRESHING NBNS REFRESHING NBNS
NODE NODE
NAME REFRESH REQUEST NAME REFRESH REQUEST
------------------------> ----------------------->
POSITIVE RESPONSE NEGATIVE RESPONSE
<------------------------ <-----------------------
!
!
V
MARK NAME IN
CONFLICT
15.5.2. NAME CHALLENGE
Name challenge is done by sending a NAME QUERY REQUEST to an end node
of any type. If a POSITIVE NAME QUERY RESPONSE is returned, then
that node still owns the name. If a NEGATIVE NAME QUERY RESPONSE is
received or if no response is received, it can be assumed that the
end node no longer owns the name.
Name challenge can be performed either by the NBNS node, or by an end
node. When an end-node sends a name claim packet, the NBNS node may
do the challenge operation. The NBNS node can choose, however, to
require the end node do the challenge. In that case, the NBNS will
send an END-NODE CHALLENGE RESPONSE packet to the end node, which
should then proceed to challenge the putative owner.
Note that the name challenge procedure sends a normal NAME QUERY
REQUEST packet to the end node. It does not require a special
packet. The only new packet introduced is the END-NODE CHALLENGE
NetBIOS Working Group [Page 46]
RFC 1001 March 1987
RESPONSE which is sent by an NBNS node when the NBNS wants the end-
node to perform the challenge operation.
15.5.3. CLEAR NAME CONFLICT
It is possible during a refresh request from a M or P node for a NBNS
to detects a name in conflict. The response to the NAME REFRESH
REQUEST must be a NEGATIVE NAME REGISTRATION RESPONSE. Optionally,
in addition, the NBNS may send a NAME CONFLICT DEMAND or a NAME
RELEASE REQUEST to the refreshing node. The NAME CONFLICT DEMAND
forces the node to place the name in the conflict state. The node
will eventually inform it's user of the conflict. The NAME RELEASE
REQUEST will force the node to flush the name from its local name
table completely. This forces the node to flush the name in
conflict. This does not cause termination of existing sessions using
this name.
The following diagram shows an NBNS detecting and correcting a
conflict:
REFRESHING NODE NBNS
NAME REFRESH REQUEST
----------------------------------------->
NEGATIVE NAME REGISTRATION RESPONSE
<-----------------------------------------
NAME CONFLICT DEMAND
<-----------------------------------------
OR
NAME RELEASE REQUEST
<-----------------------------------------
POSITIVE/NEGATIVE RELEASE REQUEST
----------------------------------------->
15.6. ADAPTER STATUS TRANSACTIONS
Adapter status is obtained from a node as follows:
1. Perform a name discovery operation to obtain the IP
addresses of a set of end-nodes.
2. Repeat until all end-nodes from the set have been used:
a. Select one end-node from the set.
b. Send a NODE STATUS REQUEST to that end-node using UDP.
NetBIOS Working Group [Page 47]
RFC 1001 March 1987
c. Await a NODE STATUS RESPONSE. (If a timely response is
not forthcoming, repeat step "b" UCAST_REQ_RETRY_COUNT
times. After the last retry, go to step "a".)
d. If the truncation bit is not set in the response, the
response contains the entire node status. Return the
status to the user and terminate this procedure.
e. If the truncation bit is set in the response, then not
all status was returned because it would not fit into
the response packet. The responder will set the
truncation bit if the IP datagram length would exceed
MAX_DATAGRAM_LENGTH. Return the status to the user and
terminate this procedure.
3. Return error to user, no status obtained.
The repetition of step 2, above, through all nodes of the set, is
optional.
Following is an example transaction of a successful Adapter Status
operation:
REQUESTING NODE NAME OWNER
NAME QUERY REQUEST
----------------------------------------->
POSITIVE NAME QUERY RESPONSE
<-----------------------------------------
NODE STATUS REQUEST
----------------------------------------->
NODE STATUS RESPONSE
<-----------------------------------------
16. NetBIOS SESSION SERVICE
The NetBIOS session service begins after one or more IP addresses
have been found for the target name. These addresses may have been
acquired using the NetBIOS name query transactions or by other means,
such as a local name table or cache.
NetBIOS session service transactions, packets, and protocols are
identical for all end-node types. They involve only directed
(point-to-point) communications.
NetBIOS Working Group [Page 48]
RFC 1001 March 1987
16.1. OVERVIEW OF NetBIOS SESSION SERVICE
Session service has three phases:
Session establishment - it is during this phase that the IP
address and TCP port of the called name is determined, and a
TCP connection is established with the remote party.
Steady state - it is during this phase that NetBIOS data
messages are exchanged over the session. Keep-alive packets
may also be exchanged if the participating nodes are so
configured.
Session close - a session is closed whenever either a party (in
the session) closes the session or it is determined that one
of the parties has gone down.
16.1.1. SESSION ESTABLISHMENT PHASE OVERVIEW
An end-node begins establishment of a session to another node by
somehow acquiring (perhaps using the name query transactions or a
local cache) the IP address of the node or nodes purported to own the
destination name.
Every end-node awaits incoming NetBIOS session requests by listening
for TCP calls to a well-known service port, SSN_SRVC_TCP_PORT. Each
incoming TCP connection represents the start of a separate NetBIOS
session initiation attempt. The NetBIOS session server, not the
ultimate application, accepts the incoming TCP connection(s).
Once the TCP connection is open, the calling node sends session
service request packet. This packet contains the following
information:
- Calling IP address (see note)
- Calling NetBIOS name
- Called IP address (see note)
- Called NetBIOS name
NOTE: The IP addresses are obtained from the TCP service
interface.
When the session service request packet arrives at the NetBIOS
server, one of the the following situations will exist:
- There exists a NetBIOS LISTEN compatible with the incoming
call and there are adequate resources to permit session
establishment to proceed.
- There exists a NetBIOS LISTEN compatible with the incoming
call, but there are inadequate resources to permit
NetBIOS Working Group [Page 49]
RFC 1001 March 1987
establishment of a session.
- The called name does, in fact, exist on the called node, but
there is no pending NetBIOS LISTEN compatible with the
incoming call.
- The called name does not exist on the called node.
In all but the first case, a rejection response is sent back over the
TCP connection to the caller. The TCP connection is then closed and
the session phase terminates. Any retry is the responsibility of the
caller. For retries in the case of a group name, the caller may use
the next member of the group rather than immediately retrying the
instant address. In the case of a unique name, the caller may
attempt an immediate retry using the same target IP address unless
the called name did not exist on the called node. In that one case,
the NetBIOS name should be re-resolved.
If a compatible LISTEN exists, and there are adequate resources, then
the session server may transform the existing TCP connection into the
NetBIOS data session. Alternatively, the session server may
redirect, or "retarget" the caller to another TCP port (and IP
address).
If the caller is redirected, the caller begins the session
establishment anew, but using the new IP address and TCP port given
in the retarget response. Again a TCP connection is created, and
again the calling and called node exchange credentials. The called
party may accept the call, reject the call, or make a further
redirection.
This mechanism is based on the presumption that, on hosts where it is
not possible to transfer open TCP connections between processes, the
host will have a central session server. Applications willing to
receive NetBIOS calls will obtain an ephemeral TCP port number, post
a TCP unspecified passive open on that port, and then pass that port
number and NetBIOS name information to the NetBIOS session server
using a NetBIOS LISTEN operation. When the call is placed, the
session server will "retarget" the caller to the application's TCP
socket. The caller will then place a new call, directly to the
application. The application has the responsibility to mimic the
session server at least to the extent of receiving the calling
credentials and then accepting or rejecting the call.
16.1.1.1. RETRYING AFTER BEING RETARGETTED
A calling node may find that it can not establish a session with a
node to which it was directed by the retargetting procedure. Since
retargetting may be nested, there is an issue whether the caller
should begin a retry at the initial starting point or back-up to an
intermediate retargetting point. The caller may use any method. A
NetBIOS Working Group [Page 50]
RFC 1001 March 1987
discussion of two such methods is in Appendix B, "Retarget
Algorithms".
16.1.1.2. SESSION ESTABLISHMENT TO A GROUP NAME
Session establishment with a group name requires special
consideration. When a NetBIOS CALL attempt is made to a group name,
name discovery will result in a list (possibly incomplete) of the
members of that group. The calling node selects one member from the
list and attempts to build a session. If that fails, the calling
node may select another member and make another attempt.
When the session service attempts to make a connection with one of
the members of the group, there is no guarantee that that member has
a LISTEN pending against that group name, that the called node even
owns, or even that the called node is operating.
16.1.2. STEADY STATE PHASE OVERVIEW
NetBIOS data messages are exchanged in the steady state. NetBIOS
messages are sent by prepending the user data with a message header
and sending the header and the user data over the TCP connection.
The receiver removes the header and passes the data to the NetBIOS
user.
In order to detect failure of one of the nodes or of the intervening
network, "session keep alive" packets may be periodically sent in the
steady state.
Any failure of the underlying TCP connection, whether a reset, a
timeout, or other failure, implies failure of the NetBIOS session.
16.1.3. SESSION TERMINATION PHASE OVERVIEW
A NetBIOS session is terminated normally when the user requests the
session to be closed or when the session service detects the remote
partner of the session has gracefully terminated the TCP connection.
A NetBIOS session is abnormally terminated when the session service
detects a loss of the connection. Connection loss can be detected
with the keep-alive function of the session service or TCP, or on the
failure of a SESSION MESSAGE send operation.
When a user requests to close a session, the service first attempts a
graceful in-band close of the TCP connection. If the connection does
not close within the SSN_CLOSE_TIMEOUT the TCP connection is aborted.
No matter how the TCP connection is terminated, the NetBIOS session
service always closes the NetBIOS session.
When the session service receives an indication from TCP that a
connection close request has been received, the TCP connection and
the NetBIOS session are immediately closed and the user is informed
NetBIOS Working Group [Page 51]
RFC 1001 March 1987
of the loss of the session. All data received up to the close
indication should be delivered, if possible, to the session's user.
16.2. SESSION ESTABLISHMENT PHASE
All the following diagrams assume a name query operation was
successfully completed by the caller node for the listener's name.
This first diagram shows the sequence of network events used to
successfully establish a session without retargetting by the
listener. The TCP connection is first established with the well-
known NetBIOS session service TCP port, SSN_SRVC_TCP_PORT. The
caller then sends a SESSION REQUEST packet over the TCP connection
requesting a session with the listener. The SESSION REQUEST contains
the caller's name and the listener's name. The listener responds
with a POSITIVE SESSION RESPONSE informing the caller this TCP
connection is accepted as the connection for the data transfer phase
of the session.
CALLER LISTENER
TCP CONNECT
====================================>
TCP ACCEPT
<===================================
SESSION REQUEST
------------------------------------>
POSITIVE RESPONSE
<-----------------------------------
The second diagram shows the sequence of network events used to
successfully establish a session when the listener does retargetting.
The session establishment procedure is the same as with the first
diagram up to the listener's response to the SESSION REQUEST. The
listener, divided into two sections, the listen processor and the
actual listener, sends a SESSION RETARGET RESPONSE to the caller.
This response states the call is acceptable, but the data transfer
TCP connection must be at the new IP address and TCP port. The
caller then re-iterates the session establishment process anew with
the new IP address and TCP port after the initial TCP connection is
closed. The new listener then accepts this connection for the data
transfer phase with a POSITIVE SESSION RESPONSE.
CALLER LISTEN PROCESSOR LISTENER
TCP CONNECT
=============================>
TCP ACCEPT
<=============================
SESSION REQUEST
----------------------------->
NetBIOS Working Group [Page 52]
RFC 1001 March 1987
SESSION RETARGET RESPONSE
<-----------------------------
TCP CLOSE
<=============================
TCP CLOSE
=============================>
TCP CONNECT
====================================================>
TCP ACCEPT
<====================================================
SESSION REQUEST
---------------------------------------------------->
POSITIVE RESPONSE
<----------------------------------------------------
The third diagram is the sequence of network events for a rejected
session request with the listener. This type of rejection could
occur with either a non-retargetting listener or a retargetting
listener. After the TCP connection is established at
SSN_SRVC_TCP_PORT, the caller sends the SESSION REQUEST over the TCP
connection. The listener does not have either a listen pending for
the listener's name or the pending NetBIOS listen is specific to
another caller's name. Consequently, the listener sends a NEGATIVE
SESSION RESPONSE and closes the TCP connection.
CALLER LISTENER
TCP CONNECT
====================================>
TCP ACCEPT
<===================================
SESSION REQUEST
------------------------------------>
NEGATIVE RESPONSE
<-----------------------------------
TCP CLOSE
<===================================
TCP CLOSE
====================================>
The fourth diagram is the sequence of network events when session
establishment fails with a retargetting listener. After being
redirected, and after the initial TCP connection is closed the caller
tries to establish a TCP connection with the new IP address and TCP
port. The connection fails because either the port is unavailable or
the target node is not active. The port unavailable race condition
occurs if another caller has already acquired the TCP connection with
the listener. For additional implementation suggestions, see
Appendix B, "Retarget Algorithms".
NetBIOS Working Group [Page 53]
RFC 1001 March 1987
CALLER LISTEN PROCESSOR LISTENER
TCP CONNECT
=============================>
TCP ACCEPT
<=============================
SESSION REQUEST
----------------------------->
REDIRECT RESPONSE
<-----------------------------
TCP CLOSE
<=============================
TCP CLOSE
=============================>
TCP CONNECT
====================================================>
CONNECTION REFUSED OR TIMED OUT
<===================================================
16.3. SESSION DATA TRANSFER PHASE
16.3.1. DATA ENCAPSULATION
NetBIOS messages are exchanged in the steady state. Messages are
sent by prepending user data with message header and sending the
header and the user data over the TCP connection. The receiver
removes the header and delivers the NetBIOS data to the user.
16.3.2. SESSION KEEP-ALIVES
In order to detect node failure or network partitioning, "session
keep alive" packets are periodically sent in the steady state. A
session keep alive packet is discarded by a peer node.
A session keep alive timer is maintained for each session. This
timer is reset whenever any data is sent to, or received from, the
session peer. When the timer expires, a NetBIOS session keep-alive
packet is sent on the TCP connection. Sending the keep-alive packet
forces data to flow on the TCP connection, thus indirectly causing
TCP to detect whether the connection is still active.
Since many TCP implementations provide a parallel TCP "keep- alive"
mechanism, the NetBIOS session keep-alive is made a configurable
option. It is recommended that the NetBIOS keep- alive mechanism be
used only in the absence of TCP keep-alive.
Note that unlike TCP keep alives, NetBIOS session keep alives do not
require a response from the NetBIOS peer -- the fact that it was
NetBIOS Working Group [Page 54]
RFC 1001 March 1987
possible to send the NetBIOS session keep alive is sufficient
indication that the peer, and the connection to it, are still active.
The only requirement for interoperability is that when a session keep
alive packet is received, it should be discarded.
17. NETBIOS DATAGRAM SERVICE
17.1. OVERVIEW OF NetBIOS DATAGRAM SERVICE
Every NetBIOS datagram has a named destination and source. To
transmit a NetBIOS datagram, the datagram service must perform a name
query operation to learn the IP address and the attributes of the
destination NetBIOS name. (This information may be cached to avoid
the overhead of name query on subsequent NetBIOS datagrams.)
NetBIOS datagrams are carried within UDP packets. If a NetBIOS
datagram is larger than a single UDP packet, it may be fragmented
into several UDP packets.
End-nodes may receive NetBIOS datagrams addressed to names not held
by the receiving node. Such datagrams should be discarded. If the
name is unique then a DATAGRAM ERROR packet is sent to the source of
that NetBIOS datagram.
17.1.1. UNICAST, MULTICAST, AND BROADCAST
NetBIOS datagrams may be unicast, multicast, or broadcast. A NetBIOS
datagram addressed to a unique NetBIOS name is unicast. A NetBIOS
datatgram addressed to a group NetBIOS name, whether there are zero,
one, or more actual members, is multicast. A NetBIOS datagram sent
using the NetBIOS "Send Broadcast Datagram" primitive is broadcast.
17.1.2. FRAGMENTATION OF NetBIOS DATAGRAMS
When the header and data of a NetBIOS datagram exceeds the maximum
amount of data allowed in a UDP packet, the NetBIOS datagram must be
fragmented before transmission and reassembled upon receipt.
A NetBIOS Datagram is composed of the following protocol elements:
- IP header of 20 bytes (minimum)
- UDP header of 8 bytes
- NetBIOS Datagram Header of 14 bytes
- The NetBIOS Datagram data.
The NetBIOS Datagram data section is composed of 3 parts:
- Source NetBIOS name (255 bytes maximum)
- Destination NetBIOS name (255 bytes maximum)
- The NetBIOS user's data (maximum of 512 bytes)
NetBIOS Working Group [Page 55]
RFC 1001 March 1987
The two name fields are in second level encoded format (see section
14.)
A maximum size NetBIOS datagram is 1064 bytes. The minimal maximum
IP datagram size is 576 bytes. Consequently, a NetBIOS Datagram may
not fit into a single IP datagram. This makes it necessary to permit
the fragmentation of NetBIOS Datagrams.
On networks meeting or exceeding the minimum IP datagram length
requirement of 576 octets, at most two NetBIOS datagram fragments
will be generated. The protocols and packet formats accommodate
fragmentation into three or more parts.
When a NetBIOS datagram is fragmented, the IP, UDP and NetBIOS
Datagram headers are present in each fragment. The NetBIOS Datagram
data section is split among resulting UDP datagrams. The data
sections of NetBIOS datagram fragments do not overlap. The only
fields of the NetBIOS Datagram header that would vary are the FLAGS
and OFFSET fields.
The FIRST bit in the FLAGS field indicate whether the fragment is the
first in a sequence of fragments. The MORE bit in the FLAGS field
indicates whether other fragments follow.
The OFFSET field is the byte offset from the beginning of the NetBIOS
datagram data section to the first byte of the data section in a
fragment. It is 0 for the first fragment. For each subsequent
fragment, OFFSET is the sum of the bytes in the NetBIOS data sections
of all preceding fragments.
If the NetBIOS datagram was not fragmented:
- FIRST = TRUE
- MORE = FALSE
- OFFSET = 0
If the NetBIOS datagram was fragmented:
- First fragment:
- FIRST = TRUE
- MORE = TRUE
- OFFSET = 0
- Intermediate fragments:
- FIRST = FALSE
- MORE = TRUE
- OFFSET = sum(NetBIOS data in prior fragments)
- Last fragment:
- FIRST = FALSE
- MORE = FALSE
NetBIOS Working Group [Page 56]
RFC 1001 March 1987
- OFFSET = sum(NetBIOS data in prior fragments)
The relative position of intermediate fragments may be ascertained
from OFFSET.
An NBDD must remember the destination name of the first fragment in
order to relay the subsequent fragments of a single NetBIOS datagram.
The name information can be associated with the subsequent fragments
through the transaction ID, DGM_ID, and the SOURCE_IP, fields of the
packet. This information can be purged by the NBDD after the last
fragment has been processed or FRAGMENT_TO time has expired since the
first fragment was received.
17.2. NetBIOS DATAGRAMS BY B NODES
For NetBIOS datagrams with a named destination (i.e. non- broadcast),
a B node performs a name discovery for the destination name before
sending the datagram. (Name discovery may be bypassed if information
from a previous discovery is held in a cache.) If the name type
returned by name discovery is UNIQUE, the datagram is unicast to the
sole owner of the name. If the name type is GROUP, the datagram is
broadcast to the entire broadcast area using the destination IP
address BROADCAST_ADDRESS.
A receiving node always filters datagrams based on the destination
name. If the destination name is not owned by the node or if no
RECEIVE DATAGRAM user operations are pending for the name, then the
datagram is discarded. For datagrams with a UNIQUE name destination,
if the name is not owned by the node then the receiving node sends a
DATAGRAM ERROR packet. The error packet originates from the
DGM_SRVC_UDP_PORT and is addressed to the SOURCE_IP and SOURCE_PORT
from the bad datagram. The receiving node quietly discards datagrams
with a GROUP name destination if the name is not owned by the node.
Since broadcast NetBIOS datagrams do not have a named destination,
the B node sends the DATAGRAM SERVICE packet(s) to the entire
broadcast area using the destination IP address BROADCAST_ADDRESS.
In order for the receiving nodes to distinguish this datagram as a
broadcast NetBIOS datagram, the NetBIOS name used as the destination
name is '*' (hexadecimal 2A) followed by 15 bytes of hexidecimal 00.
The NetBIOS scope identifier is appended to the name before it is
converted into second-level encoding. For example, if the scope
identifier is "NETBIOS.SCOPE" then the first-level encoded name would
be:
CKAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA.NETBIOS.SCOPE
According to [2], a user may not provide a NetBIOS name beginning
with "*".
For each node in the broadcast area that receives the NetBIOS
NetBIOS Working Group [Page 57]
RFC 1001 March 1987
broadcast datagram, if any RECEIVE BROADCAST DATAGRAM user operations
are pending then the data from the NetBIOS datagram is replicated and
delivered to each. If no such operations are pending then the node
silently discards the datagram.
17.3. NetBIOS DATAGRAMS BY P AND M NODES
P and M nodes do not use IP broadcast to distribute NetBIOS
datagrams.
Like B nodes, P and M nodes must perform a name discovery or use
cached information to learn whether a destination name is a group or
a unique name.
Datagrams to unique names are unicast directly to the destination by
P and M nodes, exactly as they are by B nodes.
Datagrams to group names and NetBIOS broadcast datagrams are unicast
to the NBDD. The NBDD then relays the datagrams to each of the nodes
specified by the destination name.
An NBDD may not be capable of sending a NetBIOS datagram to a
particular NetBIOS name, including the broadcast NetBIOS name ("*")
defined above. A query mechanism is available to the end- node to
determine if a NBDD will be able to relay a datagram to a given name.
Before a datagram, or its fragments, are sent to the NBDD the P or M
node may send a DATAGRAM QUERY REQUEST packet to the NBDD with the
DESTINATION_NAME from the DATAGRAM SERVICE packet(s). The NBDD will
respond with a DATAGRAM POSITIVE QUERY RESPONSE if it will relay
datagrams to the specified destination name. After a positive
response the end-node unicasts the datagram to the NBDD. If the NBDD
will not be able to relay a datagram to the destination name
specified in the query, a DATAGRAM NEGATIVE QUERY RESPONSE packet is
returned. If the NBDD can not distribute a datagram, the end-node
then has the option of getting the name's owner list from the NBNS
and sending the datagram directly to each of the owners.
An NBDD must be able to respond to DATAGRAM QUERY REQUEST packets.
The response may always be positive. However, the usage or
implementation of the query mechanism by a P or M node is optional.
An implementation may always unicast the NetBIOS datagram to the NBDD
without asking if it will be relayed. Except for the datagram query
facility described above, an NBDD provides no feedback to indicate
whether it forwarded a datagram.
18. NODE CONFIGURATION PARAMETERS
- B NODES:
- Node's permanent unique name
- Whether IGMP is in use
- Broadcast IP address to use
NetBIOS Working Group [Page 58]
RFC 1001 March 1987
- Whether NetBIOS session keep-alives are needed
- Usable UDP data field length (to control fragmentation)
- P NODES:
- Node's permanent unique name
- IP address of NBNS
- IP address of NBDD
- Whether NetBIOS session keep-alives are needed
- Usable UDP data field length (to control fragmentation)
- M NODES:
- Node's permanent unique name
- Whether IGMP is in use
- Broadcast IP address to use
- IP address of NBNS
- IP address of NBDD
- Whether NetBIOS session keep-alives are needed
- Usable UDP data field length (to control fragmentation)
19. MINIMAL CONFORMANCE
To ensure multi-vendor interoperability, a minimally conforming
implementation based on this specification must observe the following
rules:
a) A node designed to work only in a broadcast area must
conform to the B node specification.
b) A node designed to work only in an internet must conform to
the P node specification.
NetBIOS Working Group [Page 59]
RFC 1001 March 1987
REFERENCES
[1] "Protocol Standard For a NetBIOS Service on a TCP/UDP
Transport: Detailed Specifications", RFC 1002, March 1987.
[2] IBM Corp., "IBM PC Network Technical Reference Manual", No.
6322916, First Edition, September 1984.
[3] J. Postel (Ed.), "Transmission Control Protocol", RFC 793,
September 1981.
[4] MIL-STD-1778
[5] J. Postel, "User Datagram Protocol", RFC 768, 28 August
1980.
[6] J. Reynolds, J. Postel, "Assigned Numbers", RFC 990,
November 1986.
[7] J. Postel, "Internet Protocol", RFC 791, September 1981.
[8] J. Mogul, "Internet Subnets", RFC 950, October 1984
[9] J. Mogul, "Broadcasting Internet Datagrams in the Presence
of Subnets", RFC 922, October 1984.
[10] J. Mogul, "Broadcasting Internet Datagrams", RFC 919,
October 1984.
[11] P. Mockapetris, "Domain Names - Concepts and Facilities",
RFC 882, November 1983.
[12] P. Mockapetris, "Domain Names - Implementation and
Specification", RFC 883, November 1983.
[13] P. Mockapetris, "Domain System Changes and Observations",
RFC 973, January 1986.
[14] C. Partridge, "Mail Routing and the Domain System", RFC 974,
January 1986.
[15] S. Deering, D. Cheriton, "Host Groups: A Multicast Extension
to the Internet Protocol", RFC 966, December 1985.
[16] S. Deering, "Host Extensions for IP Multicasting", RFC 988,
July 1986.
NetBIOS Working Group [Page 60]
RFC 1001 March 1987
APPENDIX A
This appendix contains supporting technical discussions. It is not
an integral part of the NetBIOS-over-TCP specification.
INTEGRATION WITH INTERNET GROUP MULTICASTING
The Netbios-over-TCP system described in this RFC may be easily
integrated with the Internet Group Multicast system now being
developed for the internet.
In the main body of the RFC, the notion of a broadcast area was
considered to be a single MAC-bridged "B-LAN". However, the
protocols defined will operate over an extended broadcast area
resulting from the creation of a permanent Internet Multicast Group.
Each separate broadcast area would be based on a separate permanent
Internet Multicast Group. This multicast group address would be used
by B and M nodes as their BROADCAST_ADDRESS.
In order to base the broadcast area on a multicast group certain
additional procedures are required and certain constraints must be
met.
A-1. ADDITIONAL PROTOCOL REQUIRED IN B AND M NODES
All B or M nodes operating on an IGMP based broadcast area must have
IGMP support in their IP layer software. These nodes must perform an
IGMP join operation to enter the IGMP group before engaging in
NetBIOS activity.
A-2. CONSTRAINTS
Broadcast Areas may overlap. For this reason, end-nodes must be
careful to examine the NetBIOS scope identifiers in all received
broadcast packets.
The NetBIOS broadcast protocols were designed for a network that
exhibits a low average transit time and low rate of packet loss. An
IGMP based broadcast area must exhibit these characteristics. In
practice this will tend to constrain IGMP broadcast areas to a campus
of networks interconnected by high-speed routers and inter-router
links. It is unlikely that transcontinental broadcast areas would
exhibit the required characteristics.
NetBIOS Working Group [Page 61]
RFC 1001 March 1987
APPENDIX B
This appendix contains supporting technical discussions. It is not
an integral part of the NetBIOS-over-TCP specification.
IMPLEMENTATION CONSIDERATIONS
B-1. IMPLEMENTATION MODELS
On any participating system, there must be some sort of NetBIOS
Service to coordinate access by NetBIOS applications on that system.
To analyze the impact of the NetBIOS-over-TCP architecture, we use
the following three models of how a NetBIOS service might be
implemented:
1. Combined Service and Application Model
The NetBIOS service and application are both contained
within a single process. No interprocess communication is
assumed within the system; all communication is over the
network. If multiple applications require concurrent access
to the NetBIOS service, they must be folded into this
monolithic process.
2. Common Kernel Element Model
The NetBIOS Service is part of the operating system (perhaps
as a device driver or a front-end processor). The NetBIOS
applications are normal operating system application
processes. The common element NetBIOS service contains all
the information, such as the name and listen tables,
required to co-ordinate the activities of the applications.
3. Non-Kernel Common Element Model
The NetBIOS Service is implemented as an operating system
application process. The NetBIOS applications are other
operating system application processes. The service and the
applications exchange data via operating system interprocess
communication. In a multi-processor (e.g. network)
operating system, each module may reside on a different cpu.
The NetBIOS service process contains all the shared
information required to coordinate the activities of the
NetBIOS applications. The applications may still require a
subroutine library to facilitate access to the NetBIOS
service.
NetBIOS Working Group [Page 62]
RFC 1001 March 1987
For any of the implementation models, the TCP/IP service can be
located in the operating system or split among the NetBIOS
applications and the NetBIOS service processes.
B-1.1 MODEL INDEPENDENT CONSIDERATIONS
The NetBIOS name service associates a NetBIOS name with a host. The
NetBIOS session service further binds the name to a specific TCP port
for the duration of the session.
The name service does not need to be informed of every Listen
initiation and completion. Since the names are not bound to any TCP
port in the name service, the session service may use a different tcp
port for each session established with the same local name.
The TCP port used for the data transfer phase of a NetBIOS session
can be globally well-known, locally well-known, or ephemeral. The
choice is a local implementation issue. The RETARGET mechanism
allows the binding of the NetBIOS session to a TCP connection to any
TCP port, even to another IP node.
An implementation may use the session service's globally well- known
TCP port for the data transfer phase of the session by not using the
RETARGET mechanism and, rather, accepting the session on the initial
TCP connection. This is permissible because the caller always uses
an ephemeral TCP port.
The complexity of the called end RETARGET mechanism is only required
if a particular implementation needs it. For many real system
environments, such as an in-kernel NetBIOS service implementation, it
will not be necessary to retarget incoming calls. Rather, all
NetBIOS sessions may be multiplexed through the single, well-known,
NetBIOS session service port. These implementations will not be
burdened by the complexity of the RETARGET mechanism, nor will their
callers be required to jump through the retargetting hoops.
Nevertheless, all callers must be ready to process all possible
SESSION RETARGET RESPONSEs.
B-1.2 SERVICE OPERATION FOR EACH MODEL
It is possible to construct a NetBIOS service based on this
specification for each of the above defined implementation models.
For the common kernel element model, all the NetBIOS services, name,
datagram, and session, are simple. All the information is contained
within a single entity and can therefore be accessed or modified
easily. A single port or multiple ports for the NetBIOS sessions can
be used without adding any significant complexity to the session
establishment procedure. The only penalty is the amount of overhead
incurred to get the NetBIOS messages and operation requests/responses
NetBIOS Working Group [Page 63]
RFC 1001 March 1987
through the user and operating system boundary.
The combined service and application model is very similar to the
common kernel element model in terms of its requirements on the
NetBIOS service. The major difficulty is the internal coordination
of the multiple NetBIOS service and application processes existing in
a system of this type.
The NetBIOS name, datagram and session protocols assume that the
entities at the end-points have full control of the various well-
known TCP and UDP ports. If an implementation has multiple NetBIOS
service entities, as would be the case with, for example, multiple
applications each linked into a NetBIOS library, then that
implementation must impose some internal coordination.
Alternatively, use of the NetBIOS ports could be periodically
assigned to one application or another.
For the typical non-kernel common element mode implementation, three
permanent system-wide NetBIOS service processes would exist:
- The name server
- the datagram server
- and session server
Each server would listen for requests from the network on a UDP or
TCP well-known port. Each application would have a small piece of
the NetBIOS service built-in, possibly a library. Each application's
NetBIOS support library would need to send a message to the
particular server to request an operation, such as add name or send a
datagram or set-up a listen.
The non-kernel common element model does not require a TCP connection
be passed between the two processes, session server and application.
The RETARGET operation for an active NetBIOS Listen could be used by
the session server to redirect the session to another TCP connection
on a port allocated and owned by the application's NetBIOS support
library. The application with either a built-in or a kernel-based
TCP/IP service could then accept the RETARGETed connection request
and process it independently of the session server.
On Unix(tm) or POSIX(tm), the NetBIOS session server could create
sub-processes for incoming connections. The open sessions would be
passed through "fork" and "exec" to the child as an open file
descriptor. This approach is very limited, however. A pre- existing
process could not receive an incoming call. And all call-ed
processes would have to be sub-processes of the session server.
B-2. CASUAL AND RESTRICTED NetBIOS APPLICATIONS
Because NetBIOS was designed to operate in the open system
environment of the typical personal computer, it does not have the
NetBIOS Working Group [Page 64]
RFC 1001 March 1987
concept of privileged or unprivileged applications. In many multi-
user or multi-tasking operating systems applications are assigned
privilege capabilities. These capabilities limit the applications
ability to acquire and use system resources. For these systems it is
important to allow casual applications, those with limited system
privileges, and privileged applications, those with 'super-user'
capabilities but access to them and their required resources is
restricted, to access NetBIOS services. It is also important to
allow a systems administrator to restrict certain NetBIOS resources
to a particular NetBIOS application. For example, a file server
based on the NetBIOS services should be able to have names and TCP
ports for sessions only it can use.
A NetBIOS application needs at least two local resources to
communicate with another NetBIOS application, a NetBIOS name for
itself and, typically, a session. A NetBIOS service cannot require
that NetBIOS applications directly use privileged system resources.
For example, many systems require privilege to use TCP and UDP ports
with numbers less than 1024. This RFC requires reserved ports for
the name and session servers of a NetBIOS service implementation. It
does not require the application to have direct access these reserved
ports.
For the name service, the manager of the local name table must have
access to the NetBIOS name service's reserved UDP port. It needs to
listen for name service UDP packets to defend and define its local
names to the network. However, this manager need not be a part of a
user application in a system environment which has privilege
restrictions on reserved ports.
The internal name server can require certain privileges to add,
delete, or use a certain name, if an implementer wants the
restriction. This restriction is independent of the operation of the
NetBIOS service protocols and would not necessarily prevent the
interoperation of that implementation with another implementation.
The session server is required to own a reserved TCP port for session
establishment. However, the ultimate TCP connection used to transmit
and receive data does not have to be through that reserved port. The
RETARGET procedure the NetBIOS session to be shifted to another TCP
connection, possibly through a different port at the called end.
This port can be an unprivileged resource, with a value greater than
1023. This facilitates casual applications.
Alternately, the RETARGET mechanism allows the TCP port used for data
transmission and reception to be a reserved port. Consequently, an
application wishing to have access to its ports maintained by the
system administrator can use these restricted TCP ports. This
facilitates privileged applications.
A particular implementation may wish to require further special
NetBIOS Working Group [Page 65]
RFC 1001 March 1987
privileges for session establishment, these could be associated with
internal information. It does not have to be based solely on TCP
port allocation. For example, a given NetBIOS name may only be used
for sessions by applications with a certain system privilege level.
The decision to use reserved or unreserved ports or add any
additional name registration and usage authorization is a purely
local implementation decision. It is not required by the NetBIOS
protocols specified in the RFC.
B-3. TCP VERSUS SESSION KEEP-ALIVES
The KEEP-ALIVE is a protocol element used to validate the existence
of a connection. A packet is sent to the remote connection partner
to solicit a response which shows the connection is still
functioning. TCP KEEP-ALIVES are used at the TCP level on TCP
connections while session KEEP-ALIVES are used on NetBIOS sessions.
These protocol operations are always transparent to the connection
user. The user will only find out about a KEEP-ALIVE operation if it
fails, therefore, if the connection is lost.
The NetBIOS specification[2] requires the NetBIOS service to inform
the session user if a session is lost when it is in a passive or
active state. Therefore,if the session user is only waiting for a
receive operation and the session is dropped the NetBIOS service must
inform the session user. It cannot wait for a session send operation
before it informs the user of the loss of the connection.
This requirement stems from the management of scarce or volatile
resources by a NetBIOS application. If a particular user terminates
a session with a server application by destroying the client
application or the NetBIOS service without a NetBIOS Hang Up, the
server application will want to clean-up or free allocated resources.
This server application if it only receives and then sends a response
requires the notification of the session abort in the passive state.
The standard definition of a TCP service cannot detect loss of a
connection when it is in a passive state, waiting for a packet to
arrive. Some TCP implementations have added a KEEP-ALIVE operation
which is interoperable with implementations without this feature.
These implementations send a packet with an invalid sequence number
to the connection partner. The partner, by specification, must
respond with a packet showing the correct sequence number of the
connection. If no response is received from the remote partner
within a certain time interval then the TCP service assumes the
connection is lost.
Since many TCP implementations do not have this KEEP-ALIVE function
an optional NetBIOS KEEP-ALIVE operation has been added to the
NetBIOS session protocols. The NetBIOS KEEP-ALIVE uses the
properties of TCP to solicit a response from the remote connection
NetBIOS Working Group [Page 66]
RFC 1001 March 1987
partner. A NetBIOS session message called KEEP-ALIVE is sent to the
remote partner. Since this results in TCP sending an IP packet to
the remote partner, the TCP connection is active. TCP will discover
if the TCP connection is lost if the remote TCP partner does not
acknowledge the IP packet. Therefore, the NetBIOS session service
does not send a response to a session KEEP ALIVE message. It just
throws it away. The NetBIOS session service that transmits the KEEP
ALIVE is informed only of the failure of the TCP connection. It does
not wait for a specific response message.
A particular NetBIOS implementation should use KEEP-ALIVES if it is
concerned with maintaining compatibility with the NetBIOS interface
specification[2]. Compatibility is especially important if the
implementation wishes to support existing NetBIOS applications, which
typically require the session loss detection on their servers, or
future applications which were developed for implementations with
session loss detection.
B-4. RETARGET ALGORITHMS
This section contains 2 suggestions for RETARGET algorithms. They
are called the "straight" and "stack" methods. The algorithm in the
body of the RFC uses the straight method. Implementation of either
algorithm must take into account the Session establishment maximum
retry count. The retry count is the maximum number of TCP connect
operations allowed before a failure is reported.
The straight method forces the session establishment procedure to
begin a retry after a retargetting failure with the initial node
returned from the name discovery procedure. A retargetting failure
is when a TCP connection attempt fails because of a time- out or a
NEGATIVE SESSION RESPONSE is received with an error code specifying
NOT LISTENING ON CALLED NAME. If any other failure occurs the
session establishment procedure should retry from the call to the
name discovery procedure.
A minimum of 2 retries, either from a retargetting or a name
discovery failure. This will give the session service a chance to
re-establish a NetBIOS Listen or, more importantly, allow the NetBIOS
scope, local name service or the NBNS, to re-learn the correct IP
address of a NetBIOS name.
The stack method operates similarly to the straight method. However,
instead of retrying at the initial node returned by the name
discovery procedure, it restarts with the IP address of the last node
which sent a SESSION RETARGET RESPONSE prior to the retargetting
failure. To limit the stack method, any one host can only be tried a
maximum of 2 times.
NetBIOS Working Group [Page 67]
RFC 1001 March 1987
B-5. NBDD SERVICE
If the NBDD does not forward datagrams then don't provide Group and
Broadcast NetBIOS datagram services to the NetBIOS user. Therefore,
ignore the implementation of the query request and, when get a
negative response, acquiring the membership list of IP addresses and
sending the datagram as a unicast to each member.
B-6. APPLICATION CONSIDERATIONS
B-6.1 USE OF NetBIOS DATAGRAMS
Certain existing NetBIOS applications use NetBIOS datagrams as a
foundation for their own connection-oriented protocols. This can
cause excessive NetBIOS name query activity and place a substantial
burden on the network, server nodes, and other end- nodes. It is
recommended that this practice be avoided in new applications.
NetBIOS Working Group [Page 68]
========================================================================
Network Working Group
Request for Comments: 1002 March, 1987
PROTOCOL STANDARD FOR A NetBIOS SERVICE
ON A TCP/UDP TRANSPORT:
DETAILED SPECIFICATIONS
ABSTRACT
This RFC defines a proposed standard protocol to support NetBIOS
services in a TCP/IP environment. Both local network and internet
operation are supported. Various node types are defined to accommodate
local and internet topologies and to allow operation with or without the
use of IP broadcast.
This RFC gives the detailed specifications of the NetBIOS-over-TCP
packets, protocols, and defined constants and variables. A more general
overview is found in a companion RFC, "Protocol Standard For a NetBIOS
Service on a TCP/UDP Transport: Concepts and Methods".
NetBIOS Working Group [Page 1]
RFC 1002 March 1987
TABLE OF CONTENTS
1. STATUS OF THIS MEMO 4
2. ACKNOWLEDGEMENTS 4
3. INTRODUCTION 5
4. PACKET DESCRIPTIONS 5
4.1 NAME FORMAT 5
4.2 NAME SERVICE PACKETS 7
4.2.1 GENERAL FORMAT OF NAME SERVICE PACKETS 7
4.2.1.1 HEADER 8
4.2.1.2 QUESTION SECTION 10
4.2.1.3 RESOURCE RECORD 11
4.2.2 NAME REGISTRATION REQUEST 13
4.2.3 NAME OVERWRITE REQUEST & DEMAND 14
4.2.4 NAME REFRESH REQUEST 15
4.2.5 POSITIVE NAME REGISTRATION RESPONSE 16
4.2.6 NEGATIVE NAME REGISTRATION RESPONSE 16
4.2.7 END-NODE CHALLENGE REGISTRATION RESPONSE 17
4.2.8 NAME CONFLICT DEMAND 18
4.2.9 NAME RELEASE REQUEST & DEMAND 19
4.2.10 POSITIVE NAME RELEASE RESPONSE 20
4.2.11 NEGATIVE NAME RELEASE RESPONSE 20
4.2.12 NAME QUERY REQUEST 21
4.2.13 POSITIVE NAME QUERY RESPONSE 22
4.2.14 NEGATIVE NAME QUERY RESPONSE 23
4.2.15 REDIRECT NAME QUERY RESPONSE 24
4.2.16 WAIT FOR ACKNOWLEDGEMENT (WACK) RESPONSE 25
4.2.17 NODE STATUS REQUEST 26
4.2.18 NODE STATUS RESPONSE 27
4.3 SESSION SERVICE PACKETS 29
4.3.1 GENERAL FORMAT OF SESSION PACKETS 29
4.3.2 SESSION REQUEST PACKET 30
4.3.3 POSITIVE SESSION RESPONSE PACKET 31
4.3.4 NEGATIVE SESSION RESPONSE PACKET 31
4.3.5 SESSION RETARGET RESPONSE PACKET 31
4.3.6 SESSION MESSAGE PACKET 32
4.3.7 SESSION KEEP ALIVE PACKET 32
4.4 DATAGRAM SERVICE PACKETS 32
4.4.1 NetBIOS DATAGRAM HEADER 32
4.4.2 DIRECT_UNIQUE, DIRECT_GROUP, & BROADCAST DATAGRAM 33
4.4.3 DATAGRAM ERROR PACKET 34
4.4.4 DATAGRAM QUERY REQUEST 34
4.4.5 DATAGRAM POSITIVE AND NEGATIVE QUERY RESPONSE 34
5. PROTOCOL DESCRIPTIONS 35
5.1 NAME SERVICE PROTOCOLS 35
5.1.1 B-NODE ACTIVITY 35
NetBIOS Working Group [Page 2]
RFC 1002 March 1987
5.1.1.1 B-NODE ADD NAME 35
5.1.1.2 B-NODE ADD_GROUP NAME 37
5.1.1.3 B-NODE FIND_NAME 37
5.1.1.4 B NODE NAME RELEASE 38
5.1.1.5 B-NODE INCOMING PACKET PROCESSING 39
5.1.2 P-NODE ACTIVITY 42
5.1.2.1 P-NODE ADD_NAME 42
5.1.2.2 P-NODE ADD GROUP NAME 45
5.1.2.3 P-NODE FIND NAME 45
5.1.2.4 P-NODE DELETE_NAME 46
5.1.2.5 P-NODE INCOMING PACKET PROCESSING 47
5.1.2.6 P-NODE TIMER INITIATED PROCESSING 49
5.1.3 M-NODE ACTIVITY 50
5.1.3.1 M-NODE ADD NAME 50
5.1.3.2 M-NODE ADD GROUP NAME 54
5.1.3.3 M-NODE FIND NAME 55
5.1.3.4 M-NODE DELETE NAME 56
5.1.3.5 M-NODE INCOMING PACKET PROCESSING 58
5.1.3.6 M-NODE TIMER INITIATED PROCESSING 60
5.1.4 NBNS ACTIVITY 60
5.1.4.1 NBNS INCOMING PACKET PROCESSING 61
5.1.4.2 NBNS TIMER INITIATED PROCESSING 66
5.2 SESSION SERVICE PROTOCOLS 67
5.2.1 SESSION ESTABLISHMENT PROTOCOLS 67
5.2.1.1 USER REQUEST PROCESSING 67
5.2.1.2 RECEIVED PACKET PROCESSING 71
5.2.2 SESSION DATA TRANSFER PROTOCOLS 72
5.2.2.1 USER REQUEST PROCESSING 72
5.2.2.2 RECEIVED PACKET PROCESSING 72
5.2.2.3 PROCESSING INITIATED BY TIMER 73
5.2.3 SESSION TERMINATION PROTOCOLS 73
5.2.3.1 USER REQUEST PROCESSING 73
5.2.3.2 RECEPTION INDICATION PROCESSING 73
5.3 NetBIOS DATAGRAM SERVICE PROTOCOLS 74
5.3.1 B NODE TRANSMISSION OF NetBIOS DATAGRAMS 74
5.3.2 P AND M NODE TRANSMISSION OF NetBIOS DATAGRAMS 76
5.3.3 RECEPTION OF NetBIOS DATAGRAMS BY ALL NODES 78
5.3.4 PROTOCOLS FOR THE NBDD 80
6. DEFINED CONSTANTS AND VARIABLES 83
REFERENCES 85
NetBIOS Working Group [Page 3]
RFC 1002 March 1987
PROTOCOL STANDARD FOR A NetBIOS SERVICE
ON A TCP/UDP TRANSPORT:
DETAILED SPECIFICATIONS
1. STATUS OF THIS MEMO
This RFC specifies a proposed standard for the DARPA Internet
community. Since this topic is new to the Internet community,
discussions and suggestions are specifically requested.
Please send written comments to:
Karl Auerbach
Epilogue Technology Corporation
P.O. Box 5432
Redwood City, CA 94063
Please send online comments to:
Avnish Aggarwal
Internet: mtxinu!excelan!avnish@ucbvax.berkeley.edu
Usenet: ucbvax!mtxinu!excelan!avnish
Distribution of this memorandum is unlimited.
2. ACKNOWLEDGEMENTS
This RFC has been developed under the auspices of the Internet
Activities Board.
The following individuals have contributed to the development of
this RFC:
Avnish Aggarwal Arvind Agrawal Lorenzo Aguilar
Geoffrey Arnold Karl Auerbach K. Ramesh Babu
Keith Ball Amatzia Ben-Artzi Vint Cerf
Richard Cherry David Crocker Steve Deering
Greg Ennis Steve Holmgren Jay Israel
David Kaufman Lee LaBarre James Lau
Dan Lynch Gaylord Miyata David Stevens
Steve Thomas Ishan Wu
The system proposed by this RFC does not reflect any existing
Netbios-over-TCP implementation. However, the design
incorporates considerable knowledge obtained from prior
implementations. Special thanks goes to the following
organizations which have provided this invaluable information:
CMC/Syros Excelan Sytek Ungermann-Bass
NetBIOS Working Group [Page 4]
RFC 1002 March 1987
3. INTRODUCTION
This RFC contains the detailed packet formats and protocol
specifications for NetBIOS-over-TCP. This RFC is a companion to
RFC 1001, "Protocol Standard For a NetBIOS Service on a TCP/UDP
Transport: Concepts and Methods" [1].
4. PACKET DESCRIPTIONS
Bit and byte ordering are defined by the most recent version of
"Assigned Numbers" [2].
4.1. NAME FORMAT
The NetBIOS name representation in all NetBIOS packets (for NAME,
SESSION, and DATAGRAM services) is defined in the Domain Name
Service RFC 883[3] as "compressed" name messages. This format is
called "second-level encoding" in the section entitled
"Representation of NetBIOS Names" in the Concepts and Methods
document.
For ease of description, the first two paragraphs from page 31,
the section titled "Domain name representation and compression",
of RFC 883 are replicated here:
Domain names messages are expressed in terms of a sequence
of labels. Each label is represented as a one octet length
field followed by that number of octets. Since every domain
name ends with the null label of the root, a compressed
domain name is terminated by a length byte of zero. The
high order two bits of the length field must be zero, and
the remaining six bits of the length field limit the label
to 63 octets or less.
To simplify implementations, the total length of label
octets and label length octets that make up a domain name is
restricted to 255 octets or less.
The following is the uncompressed representation of the NetBIOS name
"FRED ", which is the 4 ASCII characters, F, R, E, D, followed by 12
space characters (0x20). This name has the SCOPE_ID: "NETBIOS.COM"
EGFCEFEECACACACACACACACACACACACA.NETBIOS.COM
This uncompressed representation of names is called "first-level
encoding" in the section entitled "Representation of NetBIOS Names"
in the Concepts and Methods document.
The following is a pictographic representation of the compressed
representation of the previous uncompressed Domain Name
representation.
NetBIOS Working Group [Page 5]
RFC 1002 March 1987
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x20 | E (0x45) | G (0x47) | F (0x46) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| C (0x43) | E (0x45) | F (0x46) | E (0x45) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| E (0x45) | C (0x43) | A (0x41) | C (0x43) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| A (0x41) | C (0x43) | A (0x41) | C (0x43) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| A (0x41) | C (0x43) | A (0x41) | C (0x43) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| A (0x41) | C (0x43) | A (0x41) | C (0x43) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| A (0x41) | C (0x43) | A (0x41) | C (0x43) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| A (0x41) | C (0x43) | A (0x41) | C (0x43) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| A (0X41) | 0x07 | N (0x4E) | E (0x45) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| T (0x54) | B (0x42) | I (0x49) | O (0x4F) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| S (0x53) | 0x03 | C (0x43) | O (0x4F) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| M (0x4D) | 0x00 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Each section of a domain name is called a label [7 (page 31)]. A
label can be a maximum of 63 bytes. The first byte of a label in
compressed representation is the number of bytes in the label. For
the above example, the first 0x20 is the number of bytes in the
left-most label, EGFCEFEECACACACACACACACACACACACA, of the domain
name. The bytes following the label length count are the characters
of the label. The following labels are in sequence after the first
label, which is the encoded NetBIOS name, until a zero (0x00) length
count. The zero length count represents the root label, which is
always null.
A label length count is actually a 6-bit field in the label length
field. The most significant 2 bits of the field, bits 7 and 6, are
flags allowing an escape from the above compressed representation.
If bits 7 and 6 are both set (11), the following 14 bits are an
offset pointer into the full message to the actual label string from
another domain name that belongs in this name. This label pointer
allows for a further compression of a domain name in a packet.
NetBIOS implementations can only use label string pointers in Name
Service packets. They cannot be used in Session or Datagram Service
packets.
NetBIOS Working Group [Page 6]
RFC 1002 March 1987
The other two possible values for bits 7 and 6 (01 and 10) of a label
length field are reserved for future use by RFC 883[2 (page 32)].
Note that the first octet of a compressed name must contain one of
the following bit patterns. (An "x" indicates a bit whose value may
be either 0 or 1.):
00100000 - Netbios name, length must be 32 (decimal)
11xxxxxx - Label string pointer
10xxxxxx - Reserved
01xxxxxx - Reserved
4.2. NAME SERVICE PACKETS
4.2.1. GENERAL FORMAT OF NAME SERVICE PACKETS
The NetBIOS Name Service packets follow the packet structure defined
in the Domain Name Service (DNS) RFC 883 [7 (pg 26-31)]. The
structures are compatible with the existing DNS packet formats,
however, additional types and codes have been added to work with
NetBIOS.
If Name Service packets are sent over a TCP connection they are
preceded by a 16 bit unsigned integer representing the length of the
Name Service packet.
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ ------ ------- +
| HEADER |
+ ------ ------- +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ QUESTION ENTRIES /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ ANSWER RESOURCE RECORDS /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ AUTHORITY RESOURCE RECORDS /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ ADDITIONAL RESOURCE RECORDS /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 7]
RFC 1002 March 1987
4.2.1.1. HEADER
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID | OPCODE | NM_FLAGS | RCODE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| QDCOUNT | ANCOUNT |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NSCOUNT | ARCOUNT |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Field Description
NAME_TRN_ID Transaction ID for Name Service Transaction.
Requestor places a unique value for each active
transaction. Responder puts NAME_TRN_ID value
from request packet in response packet.
OPCODE Packet type code, see table below.
NM_FLAGS Flags for operation, see table below.
RCODE Result codes of request. Table of RCODE values
for each response packet below.
QDCOUNT Unsigned 16 bit integer specifying the number of
entries in the question section of a Name
Service packet. Always zero (0) for responses.
Must be non-zero for all NetBIOS Name requests.
ANCOUNT Unsigned 16 bit integer specifying the number of
resource records in the answer section of a Name
Service packet.
NSCOUNT Unsigned 16 bit integer specifying the number of
resource records in the authority section of a
Name Service packet.
ARCOUNT Unsigned 16 bit integer specifying the number of
resource records in the additional records
section of a Name Service packet.
The OPCODE field is defined as:
0 1 2 3 4
+---+---+---+---+---+
| R | OPCODE |
+---+---+---+---+---+
NetBIOS Working Group [Page 8]
RFC 1002 March 1987
Symbol Bit(s) Description
OPCODE 1-4 Operation specifier:
0 = query
5 = registration
6 = release
7 = WACK
8 = refresh
R 0 RESPONSE flag:
if bit == 0 then request packet
if bit == 1 then response packet.
The NM_FLAGS field is defined as:
0 1 2 3 4 5 6
+---+---+---+---+---+---+---+
|AA |TC |RD |RA | 0 | 0 | B |
+---+---+---+---+---+---+---+
Symbol Bit(s) Description
B 6 Broadcast Flag.
= 1: packet was broadcast or multicast
= 0: unicast
RA 3 Recursion Available Flag.
Only valid in responses from a NetBIOS Name
Server -- must be zero in all other
responses.
If one (1) then the NBNS supports recursive
query, registration, and release.
If zero (0) then the end-node must iterate
for query and challenge for registration.
RD 2 Recursion Desired Flag.
May only be set on a request to a NetBIOS
Name Server.
The NBNS will copy its state into the
response packet.
If one (1) the NBNS will iterate on the
query, registration, or release.
TC 1 Truncation Flag.
NetBIOS Working Group [Page 9]
RFC 1002 March 1987
Set if this message was truncated because the
datagram carrying it would be greater than
576 bytes in length. Use TCP to get the
information from the NetBIOS Name Server.
AA 0 Authoritative Answer flag.
Must be zero (0) if R flag of OPCODE is zero
(0).
If R flag is one (1) then if AA is one (1)
then the node responding is an authority for
the domain name.
End nodes responding to queries always set
this bit in responses.
4.2.1.2. QUESTION SECTION
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ QUESTION_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| QUESTION_TYPE | QUESTION_CLASS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Field Description
QUESTION_NAME The compressed name representation of the
NetBIOS name for the request.
QUESTION_TYPE The type of request. The values for this field
are specified for each request.
QUESTION_CLASS The class of the request. The values for this
field are specified for each request.
QUESTION_TYPE is defined as:
Symbol Value Description:
NB 0x0020 NetBIOS general Name Service Resource Record
NBSTAT 0x0021 NetBIOS NODE STATUS Resource Record (See NODE
STATUS REQUEST)
QUESTION_CLASS is defined as:
NetBIOS Working Group [Page 10]
RFC 1002 March 1987
Symbol Value Description:
IN 0x0001 Internet class
4.2.1.3. RESOURCE RECORD
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| RR_TYPE | RR_CLASS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| RDLENGTH | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
/ /
/ RDATA /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Field Description
RR_NAME The compressed name representation of the
NetBIOS name corresponding to this resource
record.
RR_TYPE Resource record type code
RR_CLASS Resource record class code
TTL The Time To Live of a the resource record's
name.
RDLENGTH Unsigned 16 bit integer that specifies the
number of bytes in the RDATA field.
RDATA RR_CLASS and RR_TYPE dependent field. Contains
the resource information for the NetBIOS name.
RESOURCE RECORD RR_TYPE field definitions:
Symbol Value Description:
A 0x0001 IP address Resource Record (See REDIRECT NAME
QUERY RESPONSE)
NS 0x0002 Name Server Resource Record (See REDIRECT
NetBIOS Working Group [Page 11]
RFC 1002 March 1987
NAME QUERY RESPONSE)
NULL 0x000A NULL Resource Record (See WAIT FOR
ACKNOWLEDGEMENT RESPONSE)
NB 0x0020 NetBIOS general Name Service Resource Record
(See NB_FLAGS and NB_ADDRESS, below)
NBSTAT 0x0021 NetBIOS NODE STATUS Resource Record (See NODE
STATUS RESPONSE)
RESOURCE RECORD RR_CLASS field definitions:
Symbol Value Description:
IN 0x0001 Internet class
NB_FLAGS field of the RESOURCE RECORD RDATA field for RR_TYPE of
"NB":
1 1 1 1 1 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
| G | ONT | RESERVED |
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
Symbol Bit(s) Description:
RESERVED 3-15 Reserved for future use. Must be zero (0).
ONT 1,2 Owner Node Type:
00 = B node
01 = P node
10 = M node
11 = Reserved for future use
For registration requests this is the
claimant's type.
For responses this is the actual owner's
type.
G 0 Group Name Flag.
If one (1) then the RR_NAME is a GROUP
NetBIOS name.
If zero (0) then the RR_NAME is a UNIQUE
NetBIOS name.
The NB_ADDRESS field of the RESOURCE RECORD RDATA field for
RR_TYPE of "NB" is the IP address of the name's owner.
NetBIOS Working Group [Page 12]
RFC 1002 March 1987
4.2.2. NAME REGISTRATION REQUEST
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |0| 0x5 |0|0|1|0|0 0|B| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0001 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ QUESTION_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0006 | NB_FLAGS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB_ADDRESS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Since the RR_NAME is the same name as the QUESTION_NAME, the
RR_NAME representation must use pointers to the QUESTION_NAME
name's labels to guarantee the length of the datagram is less
than the maximum 576 bytes. See section above on name formats
and also page 31 and 32 of RFC 883, Domain Names - Implementation
and Specification, for a complete description of compressed name
label pointers.
NetBIOS Working Group [Page 13]
RFC 1002 March 1987
4.2.3. NAME OVERWRITE REQUEST & DEMAND
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |0| 0x5 |0|0|0|0|0 0|B| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0001 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ QUESTION_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0006 | NB_FLAGS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB_ADDRESS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 14]
RFC 1002 March 1987
4.2.4. NAME REFRESH REQUEST
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |0| 0x9 |0|0|0|0|0 0|B| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0001 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ QUESTION_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0006 | NB_FLAGS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB_ADDRESS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 15]
RFC 1002 March 1987
4.2.5. POSITIVE NAME REGISTRATION RESPONSE
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |1| 0x5 |1|0|1|1|0 0|0| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0006 | NB_FLAGS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB_ADDRESS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
4.2.6. NEGATIVE NAME REGISTRATION RESPONSE
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |1| 0x5 |1|0|1|1|0 0|0| RCODE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0006 | NB_FLAGS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB_ADDRESS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 16]
RFC 1002 March 1987
RCODE field values:
Symbol Value Description:
FMT_ERR 0x1 Format Error. Request was invalidly
formatted.
SRV_ERR 0x2 Server failure. Problem with NBNS, cannot
process name.
IMP_ERR 0x4 Unsupported request error. Allowable only
for challenging NBNS when gets an Update type
registration request.
RFS_ERR 0x5 Refused error. For policy reasons server
will not register this name from this host.
ACT_ERR 0x6 Active error. Name is owned by another node.
CFT_ERR 0x7 Name in conflict error. A UNIQUE name is
owned by more than one node.
4.2.7. END-NODE CHALLENGE REGISTRATION RESPONSE
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |1| 0x5 |1|0|1|0|0 0|0| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0006 | NB_FLAGS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB_ADDRESS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 17]
RFC 1002 March 1987
4.2.8. NAME CONFLICT DEMAND
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |1| 0x5 |1|0|1|1|0 0|0| 0x7 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x00000000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0006 |0|ONT|0| 0x000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x00000000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
This packet is identical to a NEGATIVE NAME REGISTRATION RESPONSE
with RCODE = CFT_ERR.
NetBIOS Working Group [Page 18]
RFC 1002 March 1987
4.2.9. NAME RELEASE REQUEST & DEMAND
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |0| 0x6 |0|0|0|0|0 0|B| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0001 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ QUESTION_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x00000000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0006 | NB_FLAGS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB_ADDRESS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Since the RR_NAME is the same name as the QUESTION_NAME, the
RR_NAME representation must use label string pointers to the
QUESTION_NAME labels to guarantee the length of the datagram is
less than the maximum 576 bytes. This is the same condition as
with the NAME REGISTRATION REQUEST.
NetBIOS Working Group [Page 19]
RFC 1002 March 1987
4.2.10. POSITIVE NAME RELEASE RESPONSE
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |1| 0x6 |1|0|0|0|0 0|0| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0006 | NB_FLAGS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB_ADDRESS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
4.2.11. NEGATIVE NAME RELEASE RESPONSE
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |1| 0x6 |1|0|0|0|0 0|0| RCODE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0006 | NB_FLAGS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB_ADDRESS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 20]
RFC 1002 March 1987
RCODE field values:
Symbol Value Description:
FMT_ERR 0x1 Format Error. Request was invalidly
formatted.
SRV_ERR 0x2 Server failure. Problem with NBNS, cannot
process name.
RFS_ERR 0x5 Refused error. For policy reasons server
will not release this name from this host.
ACT_ERR 0x6 Active error. Name is owned by another node.
Only that node may release it. A NetBIOS
Name Server can optionally allow a node to
release a name it does not own. This would
facilitate detection of inactive names for
nodes that went down silently.
4.2.12. NAME QUERY REQUEST
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |0| 0x0 |0|0|1|0|0 0|B| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0001 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ QUESTION_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 21]
RFC 1002 March 1987
4.2.13. POSITIVE NAME QUERY RESPONSE
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |1| 0x0 |1|T|1|?|0 0|0| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| RDLENGTH | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| |
/ ADDR_ENTRY ARRAY /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The ADDR_ENTRY ARRAY a sequence of zero or more ADDR_ENTRY
records. Each ADDR_ENTRY record represents an owner of a name.
For group names there may be multiple entries. However, the list
may be incomplete due to packet size limitations. Bit 22, "T",
will be set to indicate truncated data.
Each ADDR_ENTRY has the following format:
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB_FLAGS | NB_ADDRESS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NB_ADDRESS (continued) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 22]
RFC 1002 March 1987
4.2.14. NEGATIVE NAME QUERY RESPONSE
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |1| 0x0 |1|0|1|?|0 0|0| RCODE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NULL (0x000A) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x00000000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
RCODE field values:
Symbol Value Description
FMT_ERR 0x1 Format Error. Request was invalidly
formatted.
SRV_ERR 0x2 Server failure. Problem with NBNS, cannot
process name.
NAM_ERR 0x3 Name Error. The name requested does not
exist.
IMP_ERR 0x4 Unsupported request error. Allowable only
for challenging NBNS when gets an Update type
registration request.
RFS_ERR 0x5 Refused error. For policy reasons server
will not register this name from this host.
NetBIOS Working Group [Page 23]
RFC 1002 March 1987
4.2.15. REDIRECT NAME QUERY RESPONSE
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |1| 0x0 |0|0|1|0|0 0|0| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0001 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NS (0x0002) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| RDLENGTH | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
/ NSD_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| A (0x0001) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0004 | NSD_IP_ADDR |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NSD_IP_ADDR, continued |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
An end node responding to a NAME QUERY REQUEST always responds
with the AA and RA bits set for both the NEGATIVE and POSITIVE
NAME QUERY RESPONSE packets. An end node never sends a REDIRECT
NAME QUERY RESPONSE packet.
NetBIOS Working Group [Page 24]
RFC 1002 March 1987
When the requestor receives the REDIRECT NAME QUERY RESPONSE it
must reiterate the NAME QUERY REQUEST to the NBNS specified by
the NSD_IP_ADDR field of the A type RESOURCE RECORD in the
ADDITIONAL section of the response packet. This is an optional
packet for the NBNS.
The NSD_NAME and the RR_NAME in the ADDITIONAL section of the
response packet are the same name. Space can be optimized if
label string pointers are used in the RR_NAME which point to the
labels in the NSD_NAME.
The RR_NAME in the AUTHORITY section is the name of the domain
the NBNS called by NSD_NAME has authority over.
4.2.16. WAIT FOR ACKNOWLEDGEMENT (WACK) RESPONSE
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |1| 0x7 |1|0|0|0|0 0|0| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NULL (0x0020) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TTL |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0002 | OPCODE | NM_FLAGS | 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 25]
RFC 1002 March 1987
The NAME_TRN_ID of the WACK RESPONSE packet is the same
NAME_TRN_ID of the request that the NBNS is telling the requestor
to wait longer to complete. The RR_NAME is the name from the
request, if any. If no name is available from the request then
it is a null name, single byte of zero.
The TTL field of the ResourceRecord is the new time to wait, in
seconds, for the request to complete. The RDATA field contains
the OPCODE and NM_FLAGS of the request.
A TTL value of 0 means that the NBNS can not estimate the time it
may take to complete a response.
4.2.17. NODE STATUS REQUEST
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |0| 0x0 |0|0|0|0|0 0|B| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0001 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ QUESTION_NAME /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NBSTAT (0x0021) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 26]
RFC 1002 March 1987
4.2.18. NODE STATUS RESPONSE
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_TRN_ID |1| 0x0 |1|0|0|0|0 0|0| 0x0 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0001 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x0000 | 0x0000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ RR_NAME /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NBSTAT (0x0021) | IN (0x0001) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| 0x00000000 |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| RDLENGTH | NUM_NAMES | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
+ +
/ NODE_NAME ARRAY /
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+ +
/ STATISTICS /
+ +
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The NODE_NAME ARRAY is an array of zero or more NUM_NAMES entries
of NODE_NAME records. Each NODE_NAME entry represents an active
name in the same NetBIOS scope as the requesting name in the
local name table of the responder. RR_NAME is the requesting
name.
NetBIOS Working Group [Page 27]
RFC 1002 March 1987
NODE_NAME Entry:
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
+--- ---+
| |
+--- NETBIOS FORMAT NAME ---+
| |
+--- ---+
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NAME_FLAGS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The NAME_FLAGS field:
1 1 1 1 1 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
| G | ONT |DRG|CNF|ACT|PRM| RESERVED |
+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+---+
The NAME_FLAGS field is defined as:
Symbol Bit(s) Description:
RESERVED 7-15 Reserved for future use. Must be zero (0).
PRM 6 Permanent Name Flag. If one (1) then entry
is for the permanent node name. Flag is zero
(0) for all other names.
ACT 5 Active Name Flag. All entries have this flag
set to one (1).
CNF 4 Conflict Flag. If one (1) then name on this
node is in conflict.
DRG 3 Deregister Flag. If one (1) then this name
is in the process of being deleted.
ONT 1,2 Owner Node Type:
00 = B node
01 = P node
10 = M node
11 = Reserved for future use
G 0 Group Name Flag.
If one (1) then the name is a GROUP NetBIOS
name.
If zero (0) then it is a UNIQUE NetBIOS name.
NetBIOS Working Group [Page 28]
RFC 1002 March 1987
STATISTICS Field of the NODE STATUS RESPONSE:
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| UNIT_ID (Unique unit ID) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| UNIT_ID,continued | JUMPERS | TEST_RESULT |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| VERSION_NUMBER | PERIOD_OF_STATISTICS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NUMBER_OF_CRCs | NUMBER_ALIGNMENT_ERRORS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NUMBER_OF_COLLISIONS | NUMBER_SEND_ABORTS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NUMBER_GOOD_SENDS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NUMBER_GOOD_RECEIVES |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NUMBER_RETRANSMITS | NUMBER_NO_RESOURCE_CONDITIONS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| NUMBER_FREE_COMMAND_BLOCKS | TOTAL_NUMBER_COMMAND_BLOCKS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|MAX_TOTAL_NUMBER_COMMAND_BLOCKS| NUMBER_PENDING_SESSIONS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MAX_NUMBER_PENDING_SESSIONS | MAX_TOTAL_SESSIONS_POSSIBLE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SESSION_DATA_PACKET_SIZE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
4.3. SESSION SERVICE PACKETS
4.3.1. GENERAL FORMAT OF SESSION PACKETS
All session service messages are sent over a TCP connection.
All session packets are of the following general structure:
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TYPE | FLAGS | LENGTH |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ TRAILER (Packet Type Dependent) /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
The TYPE, FLAGS, and LENGTH fields are present in every session
packet.
NetBIOS Working Group [Page 29]
RFC 1002 March 1987
The LENGTH field is the number of bytes following the LENGTH
field. In other words, LENGTH is the combined size of the
TRAILER field(s). For example, the POSITIVE SESSION RESPONSE
packet always has a LENGTH field value of zero (0000) while the
RETARGET SESSION RESPONSE always has a LENGTH field value of six
(0006).
One of the bits of the FLAGS field acts as an additional, high-
order bit for the LENGTH field. Thus the cumulative size of the
trailer field(s) may range from 0 to 128K bytes.
Session Packet Types (in hexidecimal):
00 - SESSION MESSAGE
81 - SESSION REQUEST
82 - POSITIVE SESSION RESPONSE
83 - NEGATIVE SESSION RESPONSE
84 - RETARGET SESSION RESPONSE
85 - SESSION KEEP ALIVE
Bit definitions of the FLAGS field:
0 1 2 3 4 5 6 7
+---+---+---+---+---+---+---+---+
| 0 | 0 | 0 | 0 | 0 | 0 | 0 | E |
+---+---+---+---+---+---+---+---+
Symbol Bit(s) Description
E 7 Length extension, used as an additional,
high-order bit on the LENGTH field.
RESERVED 0-6 Reserved, must be zero (0)
4.3.2. SESSION REQUEST PACKET
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TYPE | FLAGS | LENGTH |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ CALLED NAME /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ CALLING NAME /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 30]
RFC 1002 March 1987
4.3.3. POSITIVE SESSION RESPONSE PACKET
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TYPE | FLAGS | LENGTH |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
4.3.4. NEGATIVE SESSION RESPONSE PACKET
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TYPE | FLAGS | LENGTH |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ERROR_CODE |
+-+-+-+-+-+-+-+-+
NEGATIVE SESSION RESPONSE packet error code values (in
hexidecimal):
80 - Not listening on called name
81 - Not listening for calling name
82 - Called name not present
83 - Called name present, but insufficient resources
8F - Unspecified error
4.3.5. SESSION RETARGET RESPONSE PACKET
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TYPE | FLAGS | LENGTH |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| RETARGET_IP_ADDRESS |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PORT |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 31]
RFC 1002 March 1987
4.3.6. SESSION MESSAGE PACKET
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TYPE | FLAGS | LENGTH |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ /
/ USER_DATA /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
4.3.7. SESSION KEEP ALIVE PACKET
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TYPE | FLAGS | LENGTH |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
4.4. DATAGRAM SERVICE PACKETS
4.4.1. NetBIOS DATAGRAM HEADER
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MSG_TYPE | FLAGS | DGM_ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SOURCE_IP |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SOURCE_PORT | DGM_LENGTH |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PACKET_OFFSET |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
MSG_TYPE values (in hexidecimal):
10 - DIRECT_UNIQUE DATAGRAM
11 - DIRECT_GROUP DATAGRAM
12 - BROADCAST DATAGRAM
13 - DATAGRAM ERROR
14 - DATAGRAM QUERY REQUEST
15 - DATAGRAM POSITIVE QUERY RESPONSE
16 - DATAGRAM NEGATIVE QUERY RESPONSE
NetBIOS Working Group [Page 32]
RFC 1002 March 1987
Bit definitions of the FLAGS field:
0 1 2 3 4 5 6 7
+---+---+---+---+---+---+---+---+
| 0 | 0 | 0 | 0 | SNT | F | M |
+---+---+---+---+---+---+---+---+
Symbol Bit(s) Description
M 7 MORE flag, If set then more NetBIOS datagram
fragments follow.
F 6 FIRST packet flag, If set then this is first
(and possibly only) fragment of NetBIOS
datagram
SNT 4,5 Source End-Node type:
00 = B node
01 = P node
10 = M node
11 = NBDD
RESERVED 0-3 Reserved, must be zero (0)
4.4.2. DIRECT_UNIQUE, DIRECT_GROUP, & BROADCAST DATAGRAM
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MSG_TYPE | FLAGS | DGM_ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SOURCE_IP |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SOURCE_PORT | DGM_LENGTH |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PACKET_OFFSET | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ |
| |
/ SOURCE_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ DESTINATION_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
/ USER_DATA /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 33]
RFC 1002 March 1987
4.4.3. DATAGRAM ERROR PACKET
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MSG_TYPE | FLAGS | DGM_ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SOURCE_IP |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SOURCE_PORT | ERROR_CODE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
ERROR_CODE values (in hexidecimal):
82 - DESTINATION NAME NOT PRESENT
83 - INVALID SOURCE NAME FORMAT
84 - INVALID DESTINATION NAME FORMAT
4.4.4. DATAGRAM QUERY REQUEST
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MSG_TYPE | FLAGS | DGM_ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SOURCE_IP |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SOURCE_PORT | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
/ DESTINATION_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
4.4.5. DATAGRAM POSITIVE AND NEGATIVE QUERY RESPONSE
1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 3 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| MSG_TYPE | FLAGS | DGM_ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SOURCE_IP |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| SOURCE_PORT | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ +
| |
/ DESTINATION_NAME /
/ /
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
NetBIOS Working Group [Page 34]
RFC 1002 March 1987
5. PROTOCOL DESCRIPTIONS
5.1. NAME SERVICE PROTOCOLS
A REQUEST packet is always sent to the well known UDP port -
NAME_SERVICE_UDP_PORT. The destination address is normally
either the IP broadcast address or the address of the NBNS - the
address of the NBNS server it set up at initialization time. In
rare cases, a request packet will be sent to an end node, e.g. a
NAME QUERY REQUEST sent to "challenge" a node.
A RESPONSE packet is always sent to the source UDP port and
source IP address of the request packet.
A DEMAND packet must always be sent to the well known UDP port -
NAME_SERVICE_UDP_PORT. There is no restriction on the target IP
address.
Terms used in this section:
tid - Transaction ID. This is a value composed from
the requestor's IP address and a unique 16 bit
value generated by the originator of the
transaction.
5.1.1. B-NODE ACTIVITY
5.1.1.1. B-NODE ADD NAME
PROCEDURE add_name(newname)
/*
* Host initiated processing for a B node
*/
BEGIN
REPEAT
/* build name service packet */
ONT = B_NODE; /* broadcast node */
G = UNIQUE; /* unique name */
TTL = 0;
broadcast NAME REGISTRATION REQUEST packet;
/*
* remote node(s) will send response packet
* if applicable
*/
NetBIOS Working Group [Page 35]
RFC 1002 March 1987
pause(BCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet is received or
retransmit count has been exceeded
IF no response packet was received THEN
BEGIN /* no response */
/*
* build packet
*/
ONT = B_NODE; /* broadcast node */
G = UNIQUE; /* unique name */
TTL = 0;
/*
* Let other nodes known you have the name
*/
broadcast NAME UPDATE REQUEST packet;
/* name can be added to local name table */
return success;
END /* no response */
ELSE
BEGIN /* got response */
/*
* Match return transaction id
* against tid sent in request
*/
IF NOT response tid = request tid THEN
BEGIN
ignore response packet;
END
ELSE
CASE packet type OF
NEGATIVE NAME REGISTRATION RESPONSE:
return failure; /* name cannot be added */
POSITIVE NAME REGISTRATION RESPONSE:
END-NODE CHALLENGE NAME REGISTRATION RESPONSE:
/*
* B nodes should normally not get this
* response.
*/
ignore packet;
NetBIOS Working Group [Page 36]
RFC 1002 March 1987
END /* case */;
END /* got response */
END /* procedure */
5.1.1.2. B-NODE ADD_GROUP NAME
PROCEDURE add_group_name(newname)
/*
* Host initiated processing for a B node
*/
BEGIN
/*
* same as for a unique name with the
* exception that the group bit (G) must
* be set in the request packets.
*/
...
G = GROUP;
...
...
/*
* broadcast request ...
*/
END
5.1.1.3. B-NODE FIND_NAME
PROCEDURE find_name(name)
/*
* Host initiated processing for a B node
*/
BEGIN
REPEAT
/*
* build packet
*/
ONT = B;
TTL = 0;
G = DONT CARE;
broadcast NAME QUERY REQUEST packet;
NetBIOS Working Group [Page 37]
RFC 1002 March 1987
/*
* a node might send response packet
*/
pause(BCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet received OR
max transmit threshold exceeded
IF no response packet received THEN
return failure;
ELSE
IF NOT response tid = request tid THEN
ignore packet;
ELSE
CASE packet type OF
POSITIVE NAME QUERY RESPONSE:
/*
* Start a timer to detect conflict.
*
* Be prepared to detect conflict if
* any more response packets are received.
*
*/
save response as authoritative response;
start_timer(CONFLICT_TIMER);
return success;
NEGATIVE NAME QUERY RESPONSE:
REDIRECT NAME QUERY RESPONSE:
/*
* B Node should normally not get either
* response.
*/
ignore response packet;
END /* case */
END /* procedure */
5.1.1.4. B NODE NAME RELEASE
PROCEDURE delete_name (name)
BEGIN
REPEAT
/*
* build packet
*/
NetBIOS Working Group [Page 38]
RFC 1002 March 1987
...
/*
* send request
*/
broadcast NAME RELEASE REQUEST packet;
/*
* no response packet expected
*/
pause(BCAST_REQ_RETRY_TIMEOUT);
UNTIL retransmit count has been exceeded
END /* procedure */
5.1.1.5. B-NODE INCOMING PACKET PROCESSING
Following processing is done when broadcast or unicast packets
are received at the NAME_SERVICE_UDP_PORT.
PROCEDURE process_incoming_packet(packet)
/*
* Processing initiated by incoming packets for a B node
*/
BEGIN
/*
* Note: response packets are always sent
* to:
* source IP address of request packet
* source UDP port of request packet
*/
CASE packet type OF
NAME REGISTRATION REQUEST (UNIQUE):
IF name exists in local name table THEN
send NEGATIVE NAME REGISTRATION RESPONSE ;
NAME REGISTRATION REQUEST (GROUP):
IF name exists in local name table THEN
BEGIN
IF local entry is a unique name THEN
send NEGATIVE NAME REGISTRATION RESPONSE ;
END
NAME QUERY REQUEST:
IF name exists in local name table THEN
BEGIN
build response packet;
NetBIOS Working Group [Page 39]
RFC 1002 March 1987
send POSITIVE NAME QUERY RESPONSE;
POSITIVE NAME QUERY RESPONSE:
IF name conflict timer is not active THEN
BEGIN
/*
* timer has expired already... ignore this
* packet
*/
return;
END
ELSE /* timer is active */
IF a response for this name has previously been
received THEN
BEGIN /* existing entry */
/*
* we sent out a request packet, and
* have already received (at least)
* one response
*
* Check if conflict exists.
* If so, send out a conflict packet.
*
* Note: detecting conflict does NOT
* affect any existing sessions.
*
*/
/*
* Check for name conflict.
* See "Name Conflict" in Concepts and Methods
*/
check saved authoritative response against
information in this response packet;
IF conflict detected THEN
BEGIN
unicast NAME CONFLICT DEMAND packet;
IF entry exists in cache THEN
BEGIN
remove entry from cache;
END
END
END /* existing entry */
ELSE
BEGIN
/*
* Note: If this was the first response
* to a name query, it would have been
* handled in the
* find_name() procedure.
NetBIOS Working Group [Page 40]
RFC 1002 March 1987
*/
ignore packet;
END
NAME CONFLICT DEMAND:
IF name exists in local name table THEN
BEGIN
mark name as conflict detected;
/*
* a name in the state "conflict detected"
* does not "logically" exist on that node.
* No further session will be accepted on
* that name.
* No datagrams can be sent against that name.
* Such an entry will not be used for
* purposes of processing incoming request
* packets.
* The only valid user NetBIOS operation
* against such a name is DELETE NAME.
*/
END
NAME RELEASE REQUEST:
IF caching is being done THEN
BEGIN
remove entry from cache;
END
NAME UPDATE REQUEST:
IF caching is being done THEN
BEGIN
IF entry exists in cache already,
update cache;
ELSE IF name is "interesting" THEN
BEGIN
add entry to cache;
END
END
NODE STATUS REQUEST:
IF name exists in local name table THEN
BEGIN
/*
* send only those names that are
* in the same scope as the scope
* field in the request packet
*/
send NODE STATUS RESPONSE;
END
END
NetBIOS Working Group [Page 41]
RFC 1002 March 1987
5.1.2. P-NODE ACTIVITY
All packets sent or received by P nodes are unicast UDP packets.
A P node sends name service requests to the NBNS node that is
specified in the P-node configuration.
5.1.2.1. P-NODE ADD_NAME
PROCEDURE add_name(newname)
/*
* Host initiated processing for a P node
*/
BEGIN
REPEAT
/*
* build packet
*/
ONT = P;
G = UNIQUE;
...
/*
* send request
*/
unicast NAME REGISTRATION REQUEST packet;
/*
* NBNS will send response packet
*/
IF receive a WACK RESPONSE THEN
pause(time from TTL field of response);
ELSE
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet is received OR
retransmit count has been exceeded
IF no response packet was received THEN
BEGIN /* no response */
/*
* NBNS is down. Cannot claim name.
*/
return failure; /* name cannot be claimed */
END /* no response */
ELSE
NetBIOS Working Group [Page 42]
RFC 1002 March 1987
BEGIN /* response */
IF NOT response tid = request tid THEN
BEGIN
/* Packet may belong to another transaction */
ignore response packet;
END
ELSE
CASE packet type OF
POSITIVE NAME REGISTRATION RESPONSE:
/*
* name can be added
*/
adjust refresh timeout value, TTL, for this name;
return success; /* name can be added */
NEGATIVE NAME REGISTRATION RESPONSE:
return failure; /* name cannot be added */
END-NODE CHALLENGE REGISTRATION REQUEST:
BEGIN /* end node challenge */
/*
* The response packet has in it the
* address of the presumed owner of the
* name. Challenge that owner.
* If owner either does not
* respond or indicates that he no longer
* owns the name, claim the name.
* Otherwise, the name cannot be claimed.
*
*/
REPEAT
/*
* build packet
*/
...
unicast NAME QUERY REQUEST packet to the
address contained in the END NODE
CHALLENGE RESPONSE packet;
/*
* remote node may send response packet
*/
pause(UCAST_REQ_RETRY_TIMEOUT);
NetBIOS Working Group [Page 43]
RFC 1002 March 1987
UNTIL response packet is received or
retransmit count has been exceeded
IF no response packet is received OR
NEGATIVE NAME QUERY RESPONSE packet
received THEN
BEGIN /* update */
/*
* name can be claimed
*/
REPEAT
/*
* build packet
*/
...
unicast NAME UPDATE REQUEST to NBNS;
/*
* NBNS node will send response packet
*/
IF receive a WACK RESPONSE THEN
pause(time from TTL field of response);
ELSE
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet is received or
retransmit count has been exceeded
IF no response packet received THEN
BEGIN /* no response */
/*
* name could not be claimed
*/
return failure;
END /* no response */
ELSE
CASE packet type OF
POSITIVE NAME REGISTRATION RESPONSE:
/*
* add name
*/
return success;
NEGATIVE NAME REGISTRATION RESPONSE:
/*
* you lose ...
*/
NetBIOS Working Group [Page 44]
RFC 1002 March 1987
return failure;
END /* case */
END /* update */
ELSE
/*
* received a positive response to the "challenge"
* Remote node still has name
*/
return failure;
END /* end node challenge */
END /* response */
END /* procedure */
5.1.2.2. P-NODE ADD GROUP NAME
PROCEDURE add_group_name(newname)
/*
* Host initiated processing for a P node
*/
BEGIN
/*
* same as for a unique name, except that the
* request packet must indicate that a
* group name claim is being made.
*/
...
G = GROUP;
...
/*
* send packet
*/
...
END
5.1.2.3. P-NODE FIND NAME
PROCEDURE find_name(name)
/*
* Host initiated processing for a P node
*/
BEGIN
NetBIOS Working Group [Page 45]
RFC 1002 March 1987
REPEAT
/*
* build packet
*/
ONT = P;
G = DONT CARE;
unicast NAME QUERY REQUEST packet;
/*
* a NBNS node might send response packet
*/
IF receive a WACK RESPONSE THEN
pause(time from TTL field of response);
ELSE
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet received OR
max transmit threshold exceeded
IF no response packet received THEN
return failure;
ELSE
IF NOT response tid = request tid THEN
ignore packet;
ELSE
CASE packet type OF
POSITIVE NAME QUERY RESPONSE:
return success;
REDIRECT NAME QUERY RESPONSE:
/*
* NBNS node wants this end node
* to use some other NBNS node
* to resolve the query.
*/
repeat query with NBNS address
in the response packet;
NEGATIVE NAME QUERY RESPONSE:
return failure;
END /* case */
END /* procedure */
5.1.2.4. P-NODE DELETE_NAME
PROCEDURE delete_name (name)
NetBIOS Working Group [Page 46]
RFC 1002 March 1987
/*
* Host initiated processing for a P node
*/
BEGIN
REPEAT
/*
* build packet
*/
...
/*
* send request
*/
unicast NAME RELEASE REQUEST packet;
IF receive a WACK RESPONSE THEN
pause(time from TTL field of response);
ELSE
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL retransmit count has been exceeded
or response been received
IF response has been received THEN
CASE packet type OF
POSITIVE NAME RELEASE RESPONSE:
return success;
NEGATIVE NAME RELEASE RESPONSE:
/*
* NBNS does want node to delete this
* name !!!
*/
return failure;
END /* case */
END /* procedure */
5.1.2.5. P-NODE INCOMING PACKET PROCESSING
Processing initiated by reception of packets at a P node
PROCEDURE process_incoming_packet(packet)
/*
* Processing initiated by incoming packets at a P node
*/
BEGIN
NetBIOS Working Group [Page 47]
RFC 1002 March 1987
/*
* always ignore UDP broadcast packets
*/
IF packet was sent as a broadcast THEN
BEGIN
ignore packet;
return;
END
CASE packet type of
NAME CONFLICT DEMAND:
IF name exists in local name table THEN
mark name as in conflict;
return;
NAME QUERY REQUEST:
IF name exists in local name table THEN
BEGIN /* name exists */
/*
* build packet
*/
...
/*
* send response to the IP address and port
* number from which the request was received.
*/
send POSITIVE NAME QUERY RESPONSE ;
return;
END /* exists */
ELSE
BEGIN /* does not exist */
/*
* send response to the requestor
*/
send NEGATIVE NAME QUERY RESPONSE ;
return;
END /* does not exist */
NODE STATUS REQUEST:
/*
* Name of "*" may be used for force node to
* divulge status for administrative purposes
*/
IF name in local name table OR name = "*" THEN
BEGIN
/*
NetBIOS Working Group [Page 48]
RFC 1002 March 1987
* Build response packet and
* send to requestor node
* Send only those names that are
* in the same scope as the scope
* in the request packet.
*/
send NODE STATUS RESPONSE;
END
NAME RELEASE REQUEST:
/*
* This will be received if the NBNS wants to flush the
* name from the local name table, or from the local
* cache.
*/
IF name exists in the local name table THEN
BEGIN
delete name from local name table;
inform user that name has been deleted;
END
ELSE
IF name has been cached locally THEN
BEGIN
remove entry from cache:
END
END /* case */
END /* procedure */
5.1.2.6. P-NODE TIMER INITIATED PROCESSING
Processing initiated by timer expiration.
PROCEDURE timer_expired()
/*
* Processing initiated by the expiration of a timer on a P node
*/
BEGIN
/*
* Send a NAME REFRESH REQUEST for each name which the
* TTL which has expired.
*/
REPEAT
build NAME REFRESH REQUEST packet;
REPEAT
send packet to NBNS;
IF receive a WACK RESPONSE THEN
pause(time from TTL field of response);
NetBIOS Working Group [Page 49]
RFC 1002 March 1987
ELSE
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet is received or
retransmit count has been exceeded
CASE packet type OF
POSITIVE NAME REGISTRATION RESPONSE:
/* successfully refreshed */
reset TTL timer for this name;
NEGATIVE NAME REGISTRATION RESPONSE:
/*
* refused, can't keep name
* assume in conflict
*/
mark name as in conflict;
END /* case */
UNTIL request sent for all names for which TTL
has expired
END /* procedure */
5.1.3. M-NODE ACTIVITY
M nodes behavior is similar to that of P nodes with the addition
of some B node-like broadcast actions. M node name service
proceeds in two steps:
1.Use broadcast UDP based name service. Depending on the
operation, goto step 2.
2.Use directed UDP name service.
The following code for M nodes is exactly the same as for a P
node, with the exception that broadcast operations are done
before P type operation is attempted.
5.1.3.1. M-NODE ADD NAME
PROCEDURE add_name(newname)
/*
* Host initiated processing for a M node
*/
BEGIN
/*
* check if name exists on the
* broadcast area
*/
NetBIOS Working Group [Page 50]
RFC 1002 March 1987
REPEAT
/* build packet */
....
broadcast NAME REGISTRATION REQUEST packet;
pause(BCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet is received or
retransmit count has been exceeded
IF valid response received THEN
BEGIN
/* cannot claim name */
return failure;
END
/*
* No objections received within the
* broadcast area.
* Send request to name server.
*/
REPEAT
/*
* build packet
*/
ONT = M;
...
unicast NAME REGISTRATION REQUEST packet;
/*
* remote NBNS will send response packet
*/
IF receive a WACK RESPONSE THEN
pause(time from TTL field of response);
ELSE
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet is received or
retransmit count has been exceeded
IF no response packet was received THEN
BEGIN /* no response */
/*
* NBNS is down. Cannot claim name.
*/
NetBIOS Working Group [Page 51]
RFC 1002 March 1987
return failure; /* name cannot be claimed */
END /* no response */
ELSE
BEGIN /* response */
IF NOT response tid = request tid THEN
BEGIN
ignore response packet;
END
ELSE
CASE packet type OF
POSITIVE NAME REGISTRATION RESPONSE:
/*
* name can be added
*/
adjust refresh timeout value, TTL;
return success; /* name can be added */
NEGATIVE NAME REGISTRATION RESPONSE:
return failure; /* name cannot be added */
END-NODE CHALLENGE REGISTRATION REQUEST:
BEGIN /* end node challenge */
/*
* The response packet has in it the
* address of the presumed owner of the
* name. Challenge that owner.
* If owner either does not
* respond or indicates that he no longer
* owns the name, claim the name.
* Otherwise, the name cannot be claimed.
*
*/
REPEAT
/*
* build packet
*/
...
/*
* send packet to address contained in the
* response packet
*/
unicast NAME QUERY REQUEST packet;
/*
* remote node may send response packet
NetBIOS Working Group [Page 52]
RFC 1002 March 1987
*/
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet is received or
retransmit count has been exceeded
IF no response packet is received THEN
BEGIN /* no response */
/*
* name can be claimed
*/
REPEAT
/*
* build packet
*/
...
unicast NAME UPDATE REQUEST to NBNS;
/*
* NBNS node will send response packet
*/
IF receive a WACK RESPONSE THEN
pause(time from TTL field of response);
ELSE
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet is received or
retransmit count has been exceeded
IF no response packet received THEN
BEGIN /* no response */
/*
* name could not be claimed
*/
return failure;
END /* no response */
ELSE
CASE packet type OF
POSITIVE NAME REGISTRATION RESPONSE:
/*
* add name
*/
return success;
NEGATIVE NAME REGISTRATION RESPONSE:
NetBIOS Working Group [Page 53]
RFC 1002 March 1987
/*
* you lose ...
*/
return failure;
END /* case */
END /* no response */
ELSE
IF NOT response tid = request tid THEN
BEGIN
ignore response packet;
END
/*
* received a response to the "challenge"
* packet
*/
CASE packet type OF
POSITIVE NAME QUERY:
/*
* remote node still has name.
*/
return failure;
NEGATIVE NAME QUERY:
/*
* remote node no longer has name
*/
return success;
END /* case */
END /* end node challenge */
END /* case */
END /* response */
END /* procedure */
5.1.3.2. M-NODE ADD GROUP NAME
PROCEDURE add_group_name(newname)
/*
* Host initiated processing for a P node
*/
BEGIN
/*
* same as for a unique name, except that the
* request packet must indicate that a
NetBIOS Working Group [Page 54]
RFC 1002 March 1987
* group name claim is being made.
*/
...
G = GROUP;
...
/*
* send packet
*/
...
END
5.1.3.3. M-NODE FIND NAME
PROCEDURE find_name(name)
/*
* Host initiated processing for a M node
*/
BEGIN
/*
* check if any node on the broadcast
* area has the name
*/
REPEAT
/* build packet */
...
broadcast NAME QUERY REQUEST packet;
pause(BCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet received OR
max transmit threshold exceeded
IF valid response received THEN
BEGIN
save response as authoritative response;
start_timer(CONFLICT_TIMER);
return success;
END
/*
* no valid response on the b'cast segment.
* Try the name server.
*/
REPEAT
NetBIOS Working Group [Page 55]
RFC 1002 March 1987
/*
* build packet
*/
ONT = M;
G = DONT CARE;
unicast NAME QUERY REQUEST packet to NBNS;
/*
* a NBNS node might send response packet
*/
IF receive a WACK RESPONSE THEN
pause(time from TTL field of response);
ELSE
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet received OR
max transmit threshold exceeded
IF no response packet received THEN
return failure;
ELSE
IF NOT response tid = request tid THEN
ignore packet;
ELSE
CASE packet type OF
POSITIVE NAME QUERY RESPONSE:
return success;
REDIRECT NAME QUERY RESPONSE:
/*
* NBNS node wants this end node
* to use some other NBNS node
* to resolve the query.
*/
repeat query with NBNS address
in the response packet;
NEGATIVE NAME QUERY RESPONSE:
return failure;
END /* case */
END /* procedure */
5.1.3.4. M-NODE DELETE NAME
PROCEDURE delete_name (name)
/*
NetBIOS Working Group [Page 56]
RFC 1002 March 1987
* Host initiated processing for a P node
*/
BEGIN
/*
* First, delete name on NBNS
*/
REPEAT
/*
* build packet
*/
...
/*
* send request
*/
unicast NAME RELEASE REQUEST packet to NBNS;
IF receive a WACK RESPONSE THEN
pause(time from TTL field of response);
ELSE
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL retransmit count has been exceeded
or response been received
IF response has been received THEN
CASE packet type OF
POSITIVE NAME RELEASE RESPONSE:
/*
* Deletion of name on b'cast segment is deferred
* until after NBNS has deleted the name
*/
REPEAT
/* build packet */
...
broadcast NAME RELEASE REQUEST;
pause(BCAST_REQ_RETRY_TIMEOUT);
UNTIL rexmt threshold exceeded
return success;
NEGATIVE NAME RELEASE RESPONSE:
/*
* NBNS does want node to delete this
* name
*/
NetBIOS Working Group [Page 57]
RFC 1002 March 1987
return failure;
END /* case */
END /* procedure */
5.1.3.5. M-NODE INCOMING PACKET PROCESSING
Processing initiated by reception of packets at a M node
PROCEDURE process_incoming_packet(packet)
/*
* Processing initiated by incoming packets at a M node
*/
BEGIN
CASE packet type of
NAME CONFLICT DEMAND:
IF name exists in local name table THEN
mark name as in conflict;
return;
NAME QUERY REQUEST:
IF name exists in local name table THEN
BEGIN /* name exists */
/*
* build packet
*/
...
/*
* send response to the IP address and port
* number from which the request was received.
*/
send POSITIVE NAME QUERY RESPONSE ;
return;
END /* exists */
ELSE
BEGIN /* does not exist */
/*
* send response to the requestor
*/
IF request NOT broadcast THEN
/*
* Don't send negative responses to
* queries sent by B nodes
*/
NetBIOS Working Group [Page 58]
RFC 1002 March 1987
send NEGATIVE NAME QUERY RESPONSE ;
return;
END /* does not exist */
NODE STATUS REQUEST:
BEGIN
/*
* Name of "*" may be used for force node to
* divulge status for administrative purposes
*/
IF name in local name table OR name = "*" THEN
/*
* Build response packet and
* send to requestor node
* Send only those names that are
* in the same scope as the scope
* in the request packet.
*/
send NODE STATUS RESPONSE;
END
NAME RELEASE REQUEST:
/*
* This will be received if the NBNS wants to flush the
* name from the local name table, or from the local
* cache.
*/
IF name exists in the local name table THEN
BEGIN
delete name from local name table;
inform user that name has been deleted;
END
ELSE
IF name has been cached locally THEN
BEGIN
remove entry from cache:
END
NAME REGISTRATION REQUEST (UNIQUE):
IF name exists in local name table THEN
send NEGATIVE NAME REGISTRATION RESPONSE ;
NAME REGISTRATION REQUEST (GROUP):
IF name exists in local name table THEN
BEGIN
IF local entry is a unique name THEN
send NEGATIVE NAME REGISTRATION RESPONSE ;
END
END /* case */
END /* procedure */
NetBIOS Working Group [Page 59]
RFC 1002 March 1987
5.1.3.6. M-NODE TIMER INITIATED PROCESSING
Processing initiated by timer expiration:
PROCEDURE timer_expired()
/*
* Processing initiated by the expiration of a timer on a M node
*/
BEGIN
/*
* Send a NAME REFRESH REQUEST for each name which the
* TTL which has expired.
*/
REPEAT
build NAME REFRESH REQUEST packet;
REPEAT
send packet to NBNS;
IF receive a WACK RESPONSE THEN
pause(time from TTL field of response);
ELSE
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL response packet is received or
retransmit count has been exceeded
CASE packet type OF
POSITIVE NAME REGISTRATION RESPONSE:
/* successfully refreshed */
reset TTL timer for this name;
NEGATIVE NAME REGISTRATION RESPONSE:
/*
* refused, can't keep name
* assume in conflict
*/
mark name as in conflict;
END /* case */
UNTIL request sent for all names for which TTL
has expired
END /* procedure */
5.1.4. NBNS ACTIVITY
A NBNS node will receive directed packets from P and M nodes.
Reply packets are always sent as directed packets to the source
IP address and UDP port number. Received broadcast packets must
be ignored.
NetBIOS Working Group [Page 60]
RFC 1002 March 1987
5.1.4.1. NBNS INCOMING PACKET PROCESSING
PROCEDURE process_incoming_packet(packet)
/*
* Incoming packet processing on a NS node
*/
BEGIN
IF packet was sent as a broadcast THEN
BEGIN
discard packet;
return;
END
CASE packet type of
NAME REGISTRATION REQUEST (UNIQUE):
IF unique name exists in data base THEN
BEGIN /* unique name exists */
/*
* NBNS node may be a "passive"
* server in that it expects the
* end node to do the challenge
* server. Such a NBNS node is
* called a "non-secure" server.
* A "secure" server will do the
* challenging before it sends
* back a response packet.
*/
IF non-secure THEN
BEGIN
/*
* build response packet
*/
...
/*
* let end node do the challenge
*/
send END-NODE CHALLENGE NAME REGISTRATION
RESPONSE;
return;
END
ELSE
/*
* secure server - do the name
* challenge operation
*/
NetBIOS Working Group [Page 61]
RFC 1002 March 1987
REPEAT
send NAME QUERY REQUEST;
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL response has been received or
retransmit count has been exceeded
IF no response was received THEN
BEGIN
/* node down */
update data base - remove entry;
update data base - add new entry;
send POSITIVE NAME REGISTRATION RESPONSE;
return;
END
ELSE
BEGIN /* challenged node replied */
/*
* challenged node replied with
* a response packet
*/
CASE packet type
POSITIVE NAME QUERY RESPONSE:
/*
* name still owned by the
* challenged node
*
* build packet and send response
*/
...
/*
* Note: The NBNS will need to
* keep track (based on transaction id) of
* the IP address and port number
* of the original requestor.
*/
send NEGATIVE NAME REGISTRATION RESPONSE;
return;
NEGATIVE NAME QUERY RESPONSE:
update data base - remove entry;
update data base - add new entry;
/*
* build response packet and send
NetBIOS Working Group [Page 62]
RFC 1002 March 1987
* response
*/
send POSITIVE NAME REGISTRATION RESPONSE;
return;
END /* case */
END /* challenged node replied */
END /* unique name exists in data base */
ELSE
IF group name exists in data base THEN
BEGIN /* group names exists */
/*
* Members of a group name are NOT
* challenged.
* Make the assumption that
* at least some of the group members
* are still alive.
* Refresh mechanism will
* allow the NBNS to detect when all
* members of a group no longer use that
* name
*/
send NEGATIVE NAME REGISTRATION RESPONSE;
END /* group name exists */
ELSE
BEGIN /* name does not exist */
/*
* Name does not exist in data base
*
* This code applies to both non-secure
* and secure server.
*/
update data base - add new entry;
send POSITIVE NAME REGISTRATION RESPONSE;
return;
END
NAME QUERY REQUEST:
IF name exists in data base THEN
BEGIN
/*
* build response packet and send to
* requestor
*/
...
send POSITIVE NAME QUERY RESPONSE;
return;
NetBIOS Working Group [Page 63]
RFC 1002 March 1987
ELSE
BEGIN
/*
* build response packet and send to
* requestor
*/
...
send NEGATIVE NAME QUERY RESPONSE;
return;
END
NAME REGISTRATION REQUEST (GROUP):
IF name exists in data base THEN
BEGIN
IF local entry is a unique name THEN
BEGIN /* local is unique */
IF non-secure THEN
BEGIN
send END-NODE CHALLENGE NAME
REGISTRATION RESPONSE;
return;
END
REPEAT
send NAME QUERY REQUEST;
pause(UCAST_REQ_RETRY_TIMEOUT);
UNTIL response received or
retransmit count exceeded
IF no response received or
NEGATIVE NAME QUERY RESPONSE
received THEN
BEGIN
update data base - remove entry;
update data base - add new entry;
send POSITIVE NAME REGISTRATION RESPONSE;
return;
END
ELSE
BEGIN
/*
* name still being held
* by challenged node
*/
send NEGATIVE NAME REGISTRATION RESPONSE;
END
END /* local is unique */
ELSE
BEGIN /* local is group */
NetBIOS Working Group [Page 64]
RFC 1002 March 1987
/*
* existing entry is a group name
*/
update data base - remove entry;
update data base - add new entry;
send POSITIVE NAME REGISTRATION RESPONSE;
return;
END /* local is group */
END /* names exists */
ELSE
BEGIN /* does not exist */
/* name does not exist in data base */
update data base - add new entry;
send POSITIVE NAME REGISTRATION RESPONSE;
return;
END /* does not exist */
NAME RELEASE REQUEST:
/*
* secure server may choose to disallow
* a node from deleting a name
*/
update data base - remove entry;
send POSITIVE NAME RELEASE RESPONSE;
return;
NAME UPDATE REQUEST:
/*
* End-node completed a successful challenge,
* no update database
*/
IF secure server THEN
send NEGATIVE NAME REGISTRATION RESPONSE;
ELSE
BEGIN /* new entry */
IF entry already exists THEN
update data base - remove entry;
update data base - add new entry;
send POSITIVE NAME REGISTRATION RESPONSE;
start_timer(TTL);
END
NAME REFRESH REQUEST:
check for consistency;
NetBIOS Working Group [Page 65]
RFC 1002 March 1987
IF node not allowed to have name THEN
BEGIN
/*
* tell end node that it can't have name
*/
send NEGATIVE NAME REGISTRATION RESPONSE;
END
ELSE
BEGIN
/*
* send confirmation response to the
* end node.
*/
send POSITIVE NAME REGISTRATION;
start_timer(TTL);
END
return;
END /* case */
END /* procedure */
5.1.4.2. NBNS TIMER INITIATED PROCESSING
A NS node uses timers to flush out entries from the data base.
Each entry in the data base is removed when its timer expires.
This time value is a multiple of the refresh TTL established when
the name was registered.
PROCEDURE timer_expired()
/*
* processing initiated by expiration of TTL for a given name
*/
BEGIN
/*
* NBNS can (optionally) ensure
* that the node is actually down
* by sending a NODE STATUS REQUEST.
* If such a request is sent, and
* no response is received, it can
* be assumed that the node is down.
*/
remove entry from data base;
END
NetBIOS Working Group [Page 66]
RFC 1002 March 1987
5.2. SESSION SERVICE PROTOCOLS
The following are variables and should be configurable by the
NetBIOS user. The default values of these variables is found in
"Defined Constants and Variables" in the Detailed
Specification.):
- SSN_RETRY_COUNT - The maximum number TCP connection attempts
allowable per a single NetBIOS call request.
- SSN_CLOSE_TIMEOUT is the time period to wait when closing the
NetBIOS session before killing the TCP connection if session
sends are outstanding.
The following are Defined Constants for the NetBIOS Session
Service. (See "Defined Constants and Variables" in the Detailed
Specification for the value of these constants):
- SSN_SRVC_TCP_PORT - is the globally well-known TCP port
allocated for the NetBIOS Session Service. The service accepts
TCP connections on this port to establish NetBIOS Sessions.
The TCP connection established to this port by the caller is
initially used for the exchange of NetBIOS control information.
The actual NetBIOS data connection may also pass through this
port or, through the retargetting facility, through another
port.
5.2.1. SESSION ESTABLISHMENT PROTOCOLS
5.2.1.1. USER REQUEST PROCESSING
PROCEDURE listen(listening name, caller name)
/*
* User initiated processing for B, P and M nodes
*
* This procedure assumes that an incoming session will be
* retargetted here by a session server.
*/
BEGIN
Do TCP listen; /* Returns TCP port used */
Register listen with Session Service, give names and
TCP port;
Wait for TCP connection to open; /* Incoming call */
Read SESSION REQUEST packet from connection
Process session request (see section on
processing initiated by the reception of session
service packets);
NetBIOS Working Group [Page 67]
RFC 1002 March 1987
Inform Session Service that NetBIOS listen is complete;
IF session established THEN
return success and session information to user;
ELSE
return failure;
END /* procedure */
PROCEDURE call(calling name, called name)
/*
* user initiated processing for B, P and M nodes
*/
/*
* This algorithm assumes that the called name is a unique name.
* If the called name is a group name, the call() procedure
* needs to cycle through the members of the group
* until either (retry_count == SSN_RETRY_COUNT) or
* the list has been exhausted.
*/
BEGIN
retry_count = 0;
retarget = FALSE; /* TRUE: caller is being retargetted */
name_query = TRUE; /* TRUE: caller must begin again with */
/* name query. */
REPEAT
IF name_query THEN
BEGIN
do name discovery, returns IP address;
TCP port = SSN_SRVC_TCP_PORT;
IF name discovery fails THEN
return failure;
ELSE
name_query = FALSE;
END
/*
* now have IP address and TCP port of
* remote party.
*/
establish TCP connection with remote party, use an
ephemeral port as source TCP port;
IF connection refused THEN
BEGIN
IF retarget THEN
BEGIN
/* retry */
retarget = FALSE;
NetBIOS Working Group [Page 68]
RFC 1002 March 1987
use original IP address and TCP port;
goto LOOP;
END
/* retry for just missed TCP listen */
pause(SESSION_RETRY_TIMER);
establish TCP connection, again use ephemeral
port as source TCP port;
IF connection refused OR
connection timed out THEN
return failure;
END
ELSE
IF connection timed out THEN
BEGIN
IF retarget THEN
BEGIN
/* retry */
retarget = FALSE;
use original IP address and TCP port;
goto LOOP;
END
ELSE
BEGIN
/*
* incorrect name discovery was done,
* try again
*/
inform name discovery process of
possible error;
name_query = TRUE;
goto LOOP;
END
END
/*
* TCP connection has been established
*/
wait for session response packet;
CASE packet type OF
POSITIVE SESSION RESPONSE:
return success and session established
information;
NEGATIVE SESSION RESPONSE:
BEGIN
NetBIOS Working Group [Page 69]
RFC 1002 March 1987
CASE error OF
NOT LISTENING ON CALLED NAME:
NOT LISTENING FOR CALLING NAME:
BEGIN
kill TCP connection;
return failure;
END
CALLED NAME NOT PRESENT:
BEGIN
/*
* called name does not exist on
* remote node
*/
inform name discovery procedure
of possible error;
IF this is a P or M node THEN
BEGIN
/*
* Inform NetBIOS Name Server
* it has returned incorrect
* information.
*/
send NAME RELEASE REQUEST for called
name and IP address to
NetBIOS Name Server;
END
/* retry from beginning */
retarget = FALSE;
name_query = TRUE;
goto LOOP;
END /* called name not present */
END /* case */
END /* negative response */
RETARGET SESSION RESPONSE:
BEGIN
close TCP connection;
extract IP address and TCP port from
response;
retarget = TRUE;
END /* retarget response */
END /* case */
LOOP: retry_count = retry_count + 1;
UNTIL (retry_count > SSN_RETRY_COUNT);
return failure;
END /* procedure */
NetBIOS Working Group [Page 70]
RFC 1002 March 1987
5.2.1.2. RECEIVED PACKET PROCESSING
These are packets received on a TCP connection before a session
has been established. The listen routines attached to a NetBIOS
user process need not implement the RETARGET response section.
The user process version, separate from a shared Session Service,
need only accept (POSITIVE SESSION RESPONSE) or reject (NEGATIVE
SESSION RESPONSE) a session request.
PROCEDURE session_packet(packet)
/*
* processing initiated by receipt of a session service
* packet for a session in the session establishment phase.
* Assumes the TCP connection has been accepted.
*/
BEGIN
CASE packet type
SESSION REQUEST:
BEGIN
IF called name does not exist on node THEN
BEGIN
send NEGATIVE SESSION RESPONSE with CALLED
NAME NOT PRESENT error code;
close TCP connection;
END
Search for a listen with CALLING NAME for CALLED
NAME;
IF matching listen is found THEN
BEGIN
IF port of listener process is port TCP
connection is on THEN
BEGIN
send POSITIVE SESSION RESPONSE;
Hand off connection to client process
and/or inform user session is
established;
END
ELSE
BEGIN
send RETARGET SESSION RESPONSE with
listener's IP address and
TCP port;
close TCP connection;
END
END
ELSE
BEGIN
/* no matching listen pending */
NetBIOS Working Group [Page 71]
RFC 1002 March 1987
send NEGATIVE SESSION RESPONSE with either
NOT LISTENING ON CALLED NAME or NOT
LISTENING FOR CALLING NAME error
code;
close TCP connection;
END
END /* session request */
END /* case */
END /* procedure */
5.2.2. SESSION DATA TRANSFER PROTOCOLS
5.2.2.1. USER REQUEST PROCESSING
PROCEDURE send_message(user_message)
BEGIN
build SESSION MESSAGE header;
send SESSION MESSAGE header;
send user_message;
reset and restart keep-alive timer;
IF send fails THEN
BEGIN
/*
* TCP connection has failed */
*/
close NetBIOS session;
inform user that session is lost;
return failure;
END
ELSE
return success;
END
5.2.2.2. RECEIVED PACKET PROCESSING
These are packets received after a session has been established.
PROCEDURE session_packet(packet)
/*
* processing initiated by receipt of a session service
* packet for a session in the data transfer phase.
*/
BEGIN
CASE packet type OF
SESSION MESSAGE:
BEGIN
process message header;
read in user data;
reset and restart keep-alive timer;
deliver data to user;
NetBIOS Working Group [Page 72]
RFC 1002 March 1987
END /* session message */
SESSION KEEP ALIVE:
discard packet;
END /* case */
END /* procedure */
5.2.2.3. PROCESSING INITIATED BY TIMER
PROCEDURE session_ka_timer()
/*
* processing initiated when session keep alive timer expires
*/
BEGIN
send SESSION KEEP ALIVE, if configured;
IF send fails THEN
BEGIN
/* remote node, or path to it, is down */
abort TCP connection;
close NetBIOS session;
inform user that session is lost;
return;
END
END /* procedure */
5.2.3. SESSION TERMINATION PROTOCOLS
5.2.3.1. USER REQUEST PROCESSING
PROCEDURE close_session()
/* initiated by a user request to close a session */
BEGIN
close gracefully the TCP connection;
WAIT for the connection to close or SSN_CLOSE_TIMEOUT
to expire;
IF time out expired THEN
abort TCP connection;
END /* procedure */
5.2.3.2. RECEPTION INDICATION PROCESSING
PROCEDURE close_indication()
/*
* initiated by a TCP indication of a close request from
* the remote connection partner.
NetBIOS Working Group [Page 73]
RFC 1002 March 1987
*/
BEGIN
close gracefully TCP connection;
close NetBIOS session;
inform user session closed by remote partner;
END /* procedure */
5.3. NetBIOS DATAGRAM SERVICE PROTOCOLS
The following are GLOBAL variables and should be NetBIOS user
configurable:
- SCOPE_ID: the non-leaf section of the domain name preceded by a
'.' which represents the domain of the NetBIOS scope for the
NetBIOS name. The following protocol description only supports
single scope operation.
- MAX_DATAGRAM_LENGTH: the maximum length of an IP datagram. The
minimal maximum length defined in for IP is 576 bytes. This
value is used when determining whether to fragment a NetBIOS
datagram. Implementations are expected to be capable of
receiving unfragmented NetBIOS datagrams up to their maximum
size.
- BROADCAST_ADDRESS: the IP address B-nodes use to send datagrams
with group name destinations and broadcast datagrams. The
default is the IP broadcast address for a single IP network.
The following are Defined Constants for the NetBIOS Datagram
Service:
- DGM_SRVC_UDP_PORT: the globally well-known UDP port allocated
where the NetBIOS Datagram Service receives UDP packets. See
section 6, "Defined Constants", for its value.
5.3.1. B NODE TRANSMISSION OF NetBIOS DATAGRAMS
PROCEDURE send_datagram(data, source, destination, broadcast)
/*
* user initiated processing on B node
*/
BEGIN
group = FALSE;
do name discovery on destination name, returns name type and
IP address;
NetBIOS Working Group [Page 74]
RFC 1002 March 1987
IF name type is group name THEN
BEGIN
group = TRUE;
END
/*
* build datagram service UDP packet;
*/
convert source and destination NetBIOS names into
half-ASCII, biased encoded name;
SOURCE_NAME = cat(source, SCOPE_ID);
SOURCE_IP = this nodes IP address;
SOURCE_PORT = DGM_SRVC_UDP_PORT;
IF NetBIOS broadcast THEN
BEGIN
DESTINATION_NAME = cat("*", SCOPE_ID)
END
ELSE
BEGIN
DESTINATION_NAME = cat(destination, SCOPE_ID)
END
MSG_TYPE = select_one_from_set
{BROADCAST, DIRECT_UNIQUE, DIRECT_GROUP}
DGM_ID = next transaction id for Datagrams;
DGM_LENGTH = length of data + length of second level encoded
source and destination names;
IF (length of the NetBIOS Datagram, including UDP and
IP headers, > MAX_DATAGRAM_LENGTH) THEN
BEGIN
/*
* fragment NetBIOS datagram into 2 UDP packets
*/
Put names into 1st UDP packet and any data that fits
after names;
Set MORE and FIRST bits in 1st UDP packet's FLAGS;
OFFSET in 1st UDP = 0;
Replicate NetBIOS Datagram header from 1st UDP packet
into 2nd UDP packet;
Put rest of data in 2nd UDP packet;
Clear MORE and FIRST bits in 2nd UDP packet's FLAGS;
OFFSET in 2nd UDP = DGM_LENGTH - number of name and
data bytes in 1st UDP;
END
BEGIN
/*
* Only need one UDP packet
*/
NetBIOS Working Group [Page 75]
RFC 1002 March 1987
USER_DATA = data;
Clear MORE bit and set FIRST bit in FLAGS;
OFFSET = 0;
END
IF (group == TRUE) OR (NetBIOS broadcast) THEN
BEGIN
send UDP packet(s) to BROADCAST_ADDRESS;
END
ELSE
BEGIN
send UDP packet(s) to IP address returned by name
discovery;
END
END /* procedure */
5.3.2. P AND M NODE TRANSMISSION OF NetBIOS DATAGRAMS
PROCEDURE send_datagram(data, source, destination, broadcast)
/*
* User initiated processing on P and M node.
*
* This processing is the same as for B nodes except for
* sending broadcast and multicast NetBIOS datagrams.
*/
BEGIN
group = FALSE;
do name discovery on destination name, returns name type
and IP address;
IF name type is group name THEN
BEGIN
group = TRUE;
END
/*
* build datagram service UDP packet;
*/
convert source and destination NetBIOS names into
half-ASCII, biased encoded name;
SOURCE_NAME = cat(source, SCOPE_ID);
SOURCE_IP = this nodes IP address;
SOURCE_PORT = DGM_SRVC_UDP_PORT;
IF NetBIOS broadcast THEN
BEGIN
DESTINATION_NAME = cat("*", SCOPE_ID)
END
ELSE
NetBIOS Working Group [Page 76]
RFC 1002 March 1987
BEGIN
DESTINATION_NAME = cat(destination, SCOPE_ID)
END
MSG_TYPE = select_one_from_set
{BROADCAST, DIRECT_UNIQUE, DIRECT_GROUP}
DGM_ID = next transaction id for Datagrams;
DGM_LENGTH = length of data + length of second level encoded
source and destination names;
IF (length of the NetBIOS Datagram, including UDP and
IP headers, > MAX_DATAGRAM_LENGTH) THEN
BEGIN
/*
* fragment NetBIOS datagram into 2 UDP packets
*/
Put names into 1st UDP packet and any data that fits
after names;
Set MORE and FIRST bits in 1st UDP packet's FLAGS;
OFFSET in 1st UDP = 0;
Replicate NetBIOS Datagram header from 1st UDP packet
into 2nd UDP packet;
Put rest of data in 2nd UDP packet;
Clear MORE and FIRST bits in 2nd UDP packet's FLAGS;
OFFSET in 2nd UDP = DGM_LENGTH - number of name and
data bytes in 1st UDP;
END
BEGIN
/*
* Only need one UDP packet
*/
USER_DATA = data;
Clear MORE bit and set FIRST bit in FLAGS;
OFFSET = 0;
END
IF (group == TRUE) OR (NetBIOS broadcast) THEN
BEGIN
/*
* Sending of following query is optional.
* Node may send datagram to NBDD immediately
* but NBDD may discard the datagram.
*/
send DATAGRAM QUERY REQUEST to NBDD;
IF response is POSITIVE QUERY RESPONSE THEN
send UDP packet(s) to NBDD Server IP address;
ELSE
BEGIN
get list of destination nodes from NBNS;
NetBIOS Working Group [Page 77]
RFC 1002 March 1987
FOR EACH node in list
BEGIN
send UDP packet(s) to this node's
IP address;
END
END
END
ELSE
BEGIN
send UDP packet(s) to IP address returned by name
discovery;
END /* procedure */
5.3.3. RECEPTION OF NetBIOS DATAGRAMS BY ALL NODES
The following algorithm discards out of order NetBIOS Datagram
fragments. An implementation which reassembles out of order
NetBIOS Datagram fragments conforms to this specification. The
fragment discard timer is initialized to the value FRAGMENT_TO.
This value should be user configurable. The default value is
given in Section 6, "Defined Constants and Variables".
PROCEDURE datagram_packet(packet)
/*
* processing initiated by datagram packet reception
* on B, P and M nodes
*/
BEGIN
/*
* if this node is a P node, ignore
* broadcast packets.
*/
IF this is a P node AND incoming packet is
a broadcast packet THEN
BEGIN
discard packet;
END
CASE packet type OF
DATAGRAM SERVICE:
BEGIN
IF FIRST bit in FLAGS is set THEN
BEGIN
IF MORE bit in FLAGS is set THEN
BEGIN
Save 1st UDP packet of the Datagram;
Set this Datagram's fragment discard
timer to FRAGMENT_TO;
NetBIOS Working Group [Page 78]
RFC 1002 March 1987
return;
END
ELSE
Datagram is composed of a single
UDP packet;
END
ELSE
BEGIN
/* Have the second fragment of a Datagram */
Search for 1st fragment by source IP address
and DGM_ID;
IF found 1st fragment THEN
Process both UDP packets;
ELSE
BEGIN
discard 2nd fragment UDP packet;
return;
END
END
IF DESTINATION_NAME is '*' THEN
BEGIN
/* NetBIOS broadcast */
deliver USER_DATA from UDP packet(s) to all
outstanding receive broadcast
datagram requests;
return;
END
ELSE
BEGIN /* non-broadcast */
/* Datagram for Unique or Group Name */
IF DESTINATION_NAME is not present in the
local name table THEN
BEGIN
/* destination not present */
build DATAGRAM ERROR packet, clear
FIRST and MORE bit, put in
this nodes IP and PORT, set
ERROR_CODE;
send DATAGRAM ERROR packet to
source IP address and port
of UDP;
discard UDP packet(s);
return;
END
ELSE
BEGIN /* good */
/*
NetBIOS Working Group [Page 79]
RFC 1002 March 1987
* Replicate received NetBIOS datagram for
* each recipient
*/
FOR EACH pending NetBIOS user's receive
datagram operation
BEGIN
IF source name of operation
matches destination name
of packet THEN
BEGIN
deliver USER_DATA from UDP
packet(s);
END
END /* for each */
return;
END /* good */
END /* non-broadcast */
END /* datagram service */
DATAGRAM ERROR:
BEGIN
/*
* name service returned incorrect information
*/
inform local name service that incorrect
information was provided;
IF this is a P or M node THEN
BEGIN
/*
* tell NetBIOS Name Server that it may
* have given incorrect information
*/
send NAME RELEASE REQUEST with name
and incorrect IP address to NetBIOS
Name Server;
END
END /* datagram error */
END /* case */
END
5.3.4. PROTOCOLS FOR THE NBDD
The key to NetBIOS Datagram forwarding service is the packet
delivered to the destination end node must have the same NetBIOS
header as if the source end node sent the packet directly to the
destination end node. Consequently, the NBDD does not reassemble
NetBIOS Datagrams. It forwards the UDP packet as is.
NetBIOS Working Group [Page 80]
RFC 1002 March 1987
PROCEDURE datagram_packet(packet)
/*
* processing initiated by a incoming datagram service
* packet on a NBDD node.
*/
BEGIN
CASE packet type OF
DATAGRAM SERVICE:
BEGIN
IF packet was sent as a directed
NetBIOS datagram THEN
BEGIN
/*
* provide group forwarding service
*
* Forward datagram to each member of the
* group. Can forward via:
* 1) get list of group members and send
* the DATAGRAM SERVICE packet unicast
* to each
* 2) use Group Multicast, if available
* 3) combination of 1) and 2)
*/
...
END
ELSE
BEGIN
/*
* provide broadcast forwarding service
*
* Forward datagram to every node in the
* NetBIOS scope. Can forward via:
* 1) get list of group members and send
* the DATAGRAM SERVICE packet unicast
* to each
* 2) use Group Multicast, if available
* 3) combination of 1) and 2)
*/
...
END
END /* datagram service */
DATAGRAM ERROR:
NetBIOS Working Group [Page 81]
RFC 1002 March 1987
BEGIN
/*
* Should never receive these because Datagrams
* forwarded have source end node IP address and
* port in NetBIOS header.
*/
send DELETE NAME REQUEST with incorrect name and
IP address to NetBIOS Name Server;
END /* datagram error */
DATAGRAM QUERY REQUEST:
BEGIN
IF can send packet to DESTINATION_NAME THEN
BEGIN
/*
* NBDD is able to relay Datagrams for
* this name
*/
send POSITIVE DATAGRAM QUERY RESPONSE to
REQUEST source IP address and UDP port
with request's DGM_ID;
END
ELSE
BEGIN
/*
* NBDD is NOT able to relay Datagrams for
* this name
*/
send NEGATIVE DATAGRAM QUERY RESPONSE to
REQUEST source IP address and UDP port
with request's DGM_ID;
END
END /* datagram query request */
END /* case */
END /* procedure */
NetBIOS Working Group [Page 82]
RFC 1002 March 1987
6. DEFINED CONSTANTS AND VARIABLES
GENERAL:
SCOPE_ID The name of the NetBIOS scope.
This is expressed as a character
string meeting the requirements of
the domain name system and without
a leading or trailing "dot".
An implementation may elect to make
this a single global value for the
node or allow it to be specified
with each separate NetBIOS name
(thus permitting cross-scope
references.)
BROADCAST_ADDRESS An IP address composed of the
nodes's network and subnetwork
numbers with all remaining bits set
to one.
I.e. "Specific subnet" broadcast
addressing according to section 2.3
of RFC 950.
BCAST_REQ_RETRY_TIMEOUT 250 milliseconds.
An adaptive timer may be used.
BCAST_REQ_RETRY_COUNT 3
UCAST_REQ_RETRY_TIMEOUT 5 seconds
An adaptive timer may be used.
UCAST_REQ_RETRY_COUNT 3
MAX_DATAGRAM_LENGTH 576 bytes (default)
NAME SERVICE:
REFRESH_TIMER Negotiated with NBNS for each name.
CONFLICT_TIMER 1 second
Implementations may chose a longer
value.
NAME_SERVICE_TCP_PORT 137 (decimal)
NetBIOS Working Group [Page 83]
RFC 1002 March 1987
NAME_SERVICE_UDP_PORT 137 (decimal)
INFINITE_TTL 0
SESSION SERVICE:
SSN_SRVC_TCP_PORT 139 (decimal)
SSN_RETRY_COUNT 4 (default)
Re-configurable by user.
SSN_CLOSE_TIMEOUT 30 seconds (default)
Re-configurable by user.
SSN_KEEP_ALIVE_TIMEOUT 60 seconds, recommended, may be set to
a higher value.
(Session keep-alives are used only
if configured.)
DATAGRAM SERVICE:
DGM_SRVC_UDP_PORT 138 (decimal)
FRAGMENT_TO 2 seconds (default)
NetBIOS Working Group [Page 84]
RFC 1002 March 1987
REFERENCES
[1] "Protocol Standard For a NetBIOS Service on a TCP/UDP
Transport: Concepts and Methods", RFC 1001, March 1987.
[2] J. Reynolds, J. Postel, "Assigned Numbers", RFC 990, November
1986.
[3] P. Mockapetris, "Domain Names - Implementation and
Specification", RFC 883, November 1983.
NetBIOS Working Group [Page 85]