Internet Engineering Task Force (IETF) F. Jounay, Ed.
Request for Comments: 7338 Orange CH
Category: Informational Y. Kamite, Ed.
ISSN: 2070-1721 NTT Communications
G. Heron
Cisco Systems
M. Bocci
Alcatel-Lucent
September 2014
Requirements and Framework for Point-to-Multipoint Pseudowires
over MPLS Packet Switched Networks
Abstract
This document presents a set of requirements and a framework for
providing a point-to-multipoint pseudowire (PW) over MPLS Packet
Switched Networks. The requirements identified in this document are
related to architecture, signaling, and maintenance aspects of point-
to-multipoint PW operation. They are proposed as guidelines for the
standardization of such mechanisms. Among other potential
applications, point-to-multipoint PWs can be used to optimize the
support of multicast Layer 2 services (Virtual Private LAN Service
and Virtual Private Multicast Service).
Status of This Memo
This document is not an Internet Standards Track specification; it is
published for informational purposes.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Not all documents
approved by the IESG are a candidate for any level of Internet
Standard; see Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc7338.
Jounay, et al. Informational [Page 1]
RFC 7338 P2MP PW Requirements September 2014
Copyright Notice
Copyright (c) 2014 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
This document may contain material from IETF Documents or IETF
Contributions published or made publicly available before November
10, 2008. The person(s) controlling the copyright in some of this
material may not have granted the IETF Trust the right to allow
modifications of such material outside the IETF Standards Process.
Without obtaining an adequate license from the person(s) controlling
the copyright in such materials, this document may not be modified
outside the IETF Standards Process, and derivative works of it may
not be created outside the IETF Standards Process, except to format
it for publication as an RFC or to translate it into languages other
than English.
Jounay, et al. Informational [Page 2]
RFC 7338 P2MP PW Requirements September 2014
Table of Contents
1. Introduction ....................................................3
1.1. Problem Statement ..........................................3
1.2. Scope of This Document .....................................4
1.3. Conventions Used in This Document ..........................4
2. Definitions .....................................................5
2.1. Acronyms ...................................................5
2.2. Terminology ................................................5
3. P2MP PW Requirements ............................................6
3.1. Reference Model ............................................6
3.2. P2MP PW and Underlying Layer ...............................7
3.3. P2MP PW Construction .......................................9
3.4. P2MP PW Signaling Requirements ............................10
3.4.1. P2MP PW Identifier .................................10
3.4.2. PW Type Mismatch ...................................10
3.4.3. Interface Parameters Sub-TLV .......................10
3.4.4. Leaf Grafting/Pruning ..............................10
3.4.5. Failure Detection and Reporting ....................11
3.4.6. Protection and Restoration .........................11
3.4.7. Scalability ........................................13
4. Backward Compatibility .........................................13
5. Security Considerations ........................................13
6. References .....................................................14
6.1. Normative References ......................................14
6.2. Informative References ....................................14
7. Acknowledgments ................................................15
8. Contributors ...................................................16
1. Introduction
1.1. Problem Statement
As defined in the pseudowire architecture [RFC3985], a pseudowire
(PW) is a mechanism that emulates the essential attributes of a
telecommunications service (such as a T1 leased line or Frame Relay)
over an IP or MPLS Packet Switched Network (PSN). It provides a
single service that is perceived by its user as an unshared link or
circuit of the chosen service. A pseudowire is used to transport
Layer 1 or Layer 2 traffic (e.g., Ethernet, Time-Division
Multiplexing (TDM), ATM, and Frame Relay) over a Layer 3 PSN.
Pseudowire Emulation Edge-to-Edge (PWE3) operates "edge to edge" to
provide the required connectivity between the two endpoints of the
PW.
The point-to-multipoint (P2MP) topology described in [VPMS-REQS] and
required to provide P2MP Layer 2 VPN service can be achieved using
one or more P2MP PWs. The use of PW encapsulation enables P2MP
Jounay, et al. Informational [Page 3]
RFC 7338 P2MP PW Requirements September 2014
services to transport Layer 1 or Layer 2 data. This could be
achieved using a set of point-to-point PWs, with traffic replication
at the Root Provider Edge (PE), but at the cost of bandwidth
efficiency, as duplicate traffic would be carried multiple times on
shared links.
This document defines the requirements for a point-to-multipoint PW
(P2MP PW). A P2MP PW is a mechanism that emulates the essential
attributes of a P2MP telecommunications service such as a P2MP ATM
Virtual Circuit over a Packet Switched Network.
The required functions of P2MP PWs include encapsulating service-
specific Protocol Data Units (PDUs) arriving at an ingress Attachment
Circuit (AC), carrying them across a tunnel to one or more egress
ACs, managing their timing and order, and any other operations
required to emulate the behavior and characteristics of the service
as faithfully as possible.
1.2. Scope of This Document
The document describes the general architecture of P2MP PW with a
reference model, mentions the notion of data encapsulation, and
outlines specific requirements for the setup and maintenance of a
P2MP PW. In this document, the requirements focus on the Single-
Segment PW model. The requirements for realizing P2MP PW in the
Multi-Segment PW model [RFC5254] are left for further study. This
document refers to [RFC3916] for other aspects of P2MP PW
implementation, such as "Packet Processing" (Section 4 of that
document) and "Faithfulness of Emulated Services" (Section 7 of that
document).
1.3. Conventions Used in This Document
Although this is a requirements specification not a protocol
specification, the key words "MUST", "MUST NOT", "REQUIRED", "SHALL",
"SHALL NOT", "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and
"OPTIONAL" in this document are to be interpreted to apply to
protocol solutions designed to meet these requirements as described
in [RFC2119].
Jounay, et al. Informational [Page 4]
RFC 7338 P2MP PW Requirements September 2014
2. Definitions
2.1. Acronyms
P2P: Point-to-Point
P2MP: Point-to-Multipoint
PW: Pseudowire
PSN: Packet Switched Network
SS-PW: Single-Segment Pseudowire
2.2. Terminology
This document uses terminology described in [RFC5659]. It also
introduces additional terms needed in the context of P2MP PW.
P2MP PW (also referred to as PW tree):
Point-to-Multipoint Pseudowire. A PW attached to a source
Customer Edge (CE) used to distribute Layer 1 or Layer 2 traffic
to a set of one or more receiver CEs. The P2MP PW is
unidirectional (i.e., carrying traffic from Root PE to Leaf PEs)
and optionally supports a return path.
P2MP SS-PW:
Point-to-Multipoint Single-Segment Pseudowire. A single-segment
P2MP PW set up between the Root PE attached to the source CE and
the Leaf PEs attached to the receiver CEs. The P2MP SS-PW uses
P2MP Label Switched Paths (LSPs) as PSN tunnels.
Root PE:
P2MP PW Root Provider Edge. The PE attached to the traffic source
CE for the P2MP PW via an Attachment Circuit (AC).
Leaf PE:
P2MP PW Leaf Provider Edge. A PE attached to a set of one or more
traffic receiver CEs, via ACs. The Leaf PE replicates traffic to
the CEs based on its Forwarder function [RFC3985].
P2MP PSN Tunnel:
In the P2MP SS-PW topology, the PSN tunnel is a general term
indicating a virtual P2MP connection between the Root PE and the
Leaf PEs. A P2MP tunnel may potentially carry multiple P2MP PWs
inside (aggregation). This document uses terminology from the
document describing the MPLS multicast architecture [RFC5332] for
MPLS PSN.
Jounay, et al. Informational [Page 5]
RFC 7338 P2MP PW Requirements September 2014
3. P2MP PW Requirements
3.1. Reference Model
As per the definition in [RFC3985], a pseudowire (PW) both originates
and terminates on the edge of the same packet switched network (PSN).
The PW label is unchanged between the originating and terminating
Provider Edges (PEs). This is also known as a single-segment
pseudowire (SS-PW) -- the most fundamental network model of PWE3.
A P2MP PW can be defined as point-to-multipoint connectivity from a
Root PE connected to a traffic source CE to one or more Leaf PEs
connected to traffic receiver CEs. It is considered to be an
extended architecture of the existing P2P SS-PW technology.
Figure 1 describes the P2MP PW reference model that is derived from
[RFC3985] to support P2MP emulated services.
|<-------------P2MP PW------------->|
Native | | Native
ROOT Service | |<----P2MP PSN tunnel --->| | Service LEAF
V (AC) V V V V (AC) V
| +----+ +-----+ +----+ |
| |PE1 | | P |=========|PE2 |AC2 | +----+
| | | | ......PW1.......>|---------->|CE2 |
| | | | . |=========| | | +----+
| | | | . | +----+ |
| | |=========| . | |
| | | | . | +----+ |
+----+ | AC1 | | | . |=========|PE3 |AC3 | +----+
|CE1 |-------->|........PW1.............PW1.......>|---------->|CE3 |
+----+ | | | | . |=========| | | +----+
| | | | . | +----+ |
| | |=========| . | |
| | | | . | +----+AC4 | +----+
| | | | . |=========|PE4 |---------->|CE4 |
| | | | ......PW1.......>| | +----+
| | | | |=========| |AC5 | +----+
| | | | | | |---------->|CE5 |
| +----+ +-----+ +----+ | +----+
Figure 1: P2MP PW Reference Model
This architecture applies to the case where a P2MP PSN tunnel extends
between edge nodes of a single PSN domain to transport a
unidirectional P2MP PW with endpoints at these edge nodes. In this
model, a single copy of each PW packet is sent over the PW on the
P2MP PSN tunnel and is received by all Leaf PEs due to the P2MP
Jounay, et al. Informational [Page 6]
RFC 7338 P2MP PW Requirements September 2014
nature of the PSN tunnel. The P2MP PW SHOULD be traffic optimized,
i.e., only one copy of a P2MP PW packet or PSN tunnel (underlying
layer) packet is sent on any single link along the P2MP path. P
routers participate in P2MP PSN tunnel operation but not in the
signaling of P2MP PWs.
The Reference Model outlines the basic pieces of a P2MP PW. However,
several levels of replication need to be considered when designing a
P2MP PW solution:
- Ingress PE replication to CEs: traffic is replicated to a set of
local receiver CEs
- P router replication in the core: traffic is replicated by means
of a P2MP PSN tunnel (P2MP LSP)
- Egress PE replication to CEs: traffic is replicated to local
receiver CEs
Theoretically, it is also possible to consider Ingress PE replication
in the core; that is, all traffic is replicated to a set of P2P PSN
transport tunnels at ingress, not using P router replication at all.
However, this approach may lead to duplicate copies of each PW packet
being sent over the same physical link, specifically in the case
where multiple PSN tunnels transit that physical link. Hence, this
approach is not preferred.
Specific operations that MUST be performed at the PE on the native
data units are not described here since the required pre-processing
(Forwarder (FWRD) and Native Service Processing (NSP)) defined in
Section 4.2 of [RFC3985] is also applicable to P2MP PW.
P2MP PWs are generally unidirectional, but a Root PE may need to
receive unidirectional P2P return traffic from any Leaf PE. For that
purpose, the P2MP PW solution MAY support an optional return path
from each Leaf PE to the Root PE.
3.2. P2MP PW and Underlying Layer
The definition of MPLS multicast encapsulation [RFC5332] specifies
the procedure to carry MPLS packets that are to be replicated and a
copy of the packet sent to each of the specified next hops. This
notion is also applicable to a P2MP PW packet carried by a P2MP PSN
tunnel.
To be more precise, a P2MP PSN tunnel corresponds to a "point-to-
multipoint data link or tunnel" described in Section 3 of [RFC5332].
Jounay, et al. Informational [Page 7]
RFC 7338 P2MP PW Requirements September 2014
Similarly, P2MP PW labels correspond to "the top labels (before
applying the data link or tunnel encapsulation) of all MPLS packets
that are transmitted on a particular point-to-multipoint data link or
tunnel".
In the P2MP PW architecture using the SS-PW network model, the PW-PDU
[RFC3985] is replicated by the underlying P2MP PSN tunnel layer.
Note that the PW label is unchanged, and hidden in switching, by the
transit P routers.
In a solution, a P2MP PW MUST be supported over a single P2MP PSN
tunnel as the underlying layer of traffic distribution. Figure 2
gives an example of P2MP PW topology relying on a single P2MP LSP.
The PW tree is composed of one Root PE (i1) and several Leaf PEs (e1,
e2, e3, e4).
The mechanisms for establishing the PSN tunnel are outside the scope
of this document, as long as they enable the essential attributes of
the service to be emulated.
i1
/
/ \
/ \
/ \
/\ \
/ \ \
/ \ \
/ \ / \
e1 e2 e3 e4
Figure 2: Example of P2MP Underlying Layer for P2MP PW
A single P2MP PSN tunnel MUST be able to serve the traffic from more
than one P2MP PW in an aggregated way, i.e., multiplexing.
A P2MP PW solution MAY support different P2MP PSN tunneling
technology (e.g., MPLS over GRE [RFC4023] or P2MP MPLS LSP) or
different setup protocols (e.g., multipoint extensions for LDP (mLDP)
[RFC6388] and P2MP RSVP-TE [RFC4875]).
The P2MP LSP associated to the P2MP PW can be selected either by user
configuration or by dynamically using a multiplexing/demultiplexing
mechanism.
The P2MP PW multiplexing SHOULD be used based on the overlap rate
between P2MP LSP and P2MP PW. As an example, an existing P2MP LSP
may attach more leaves than the ones defined as Leaf PEs for a given
Jounay, et al. Informational [Page 8]
RFC 7338 P2MP PW Requirements September 2014
P2MP PW. It may be attractive to reuse it to minimize new
configuration, but using this P2MP LSP would cause non-Leaf PEs
(i.e., not part of the P2MP PW) to receive unwanted traffic.
Note: no special configuration is needed for non-Leaf PEs to drop
that unwanted traffic because they do not have forwarding information
entries unless they process the setup operation for corresponding
P2MP PWs (e.g., signaling).
The operator SHOULD determine whether it is acceptable to partially
multiplex the P2MP PW onto a P2MP LSP, and a minimum congruency rate
may be defined to enable the Root PE to make this determination. The
congruency rate SHOULD take into account several items, including:
- the amount of overlap between the Leaf PEs of the P2MP PW and the
existing egress PE routers of the P2MP LSP. If there is a
complete overlap, the congruency is perfect and the rate is 100%.
- the impact on other traffic (e.g., from other VPNs) supported over
the P2MP LSP.
With this procedure, a P2MP PW is nested within a P2MP LSP. This
allows multiplexing several PWs over a common P2MP LSP. Prior to the
P2MP PW signaling phase, the Root PE determines which P2MP LSP will
be used for this P2MP PW. The PSN tunnel can be an existing PSN
tunnel or the Root PE can create a new P2MP PSN tunnel. Note that
the ingress PE may modify or re-create an existing P2MP PSN tunnel in
order to add one or more leaf PEs to enable it to transport the P2MP
PW.
3.3. P2MP PW Construction
[RFC5332] introduces two approaches to assigning MPLS labels (meaning
PW labels in the P2MP PW context): Upstream-Assigned [RFC5331] and
Downstream-Assigned. However, it is out of scope of this document
which one should be used in PW construction. It is left to the
specification of the solution.
The following requirements apply to the establishment of P2MP PWs:
- PE nodes MUST be configurable with the P2MP PW identifiers and
ACs.
- A discovery mechanism SHOULD allow the Root PE to discover the
Leaf PEs, or vice versa.
Jounay, et al. Informational [Page 9]
RFC 7338 P2MP PW Requirements September 2014
- Solutions SHOULD allow single-sided operation at the Root PE for
the selection of some AC(s) at the Leaf PE(s) to be attached to
the PW tree so that the Root PE controls the leaf attachment.
- The Root PE SHOULD support a method to be informed about whether a
Leaf PE has successfully attached to the PW tree.
3.4. P2MP PW Signaling Requirements
3.4.1. P2MP PW Identifier
The P2MP PW MUST be uniquely identified. This unique P2MP PW
identifier MUST be used for all signaling procedures related to this
PW (PW setup, monitoring, etc.).
3.4.2. PW Type Mismatch
The Root PE and Leaf PEs of a P2MP PW MUST be configured with the
same PW type as defined in [RFC4446] for P2P PW. In case of a type
mismatch, a PE SHOULD abort attempts to attach the Leaf PE to the
P2MP PW.
3.4.3. Interface Parameters Sub-TLV
Some interface parameters [RFC4446] related to the AC capability have
been defined according to the PW type and are signaled during the PW
setup.
Where applicable, a solution is REQUIRED to ascertain whether the AC
at the Leaf PE is capable of supporting traffic coming from the AC at
the Root PE.
In case of a mismatch, the passive PE (Root or Leaf PE, depending on
the signaling process) SHOULD support mechanisms to reject attempts
to attach the Leaf PE to the P2MP PW.
3.4.4. Leaf Grafting/Pruning
Once the PW tree is established, the solution MUST allow the addition
or removal of a Leaf PE, or a subset of leaves to/from the existing
tree, without any impact on the PW tree (data and control planes) for
the remaining Leaf PEs.
The addition or removal of a Leaf PE MUST also allow the P2MP PSN
tunnel to be updated accordingly. This may cause the P2MP PSN tunnel
to add or remove the corresponding Leaf PE.
Jounay, et al. Informational [Page 10]
RFC 7338 P2MP PW Requirements September 2014
3.4.5. Failure Detection and Reporting
Since the underlying layer has an end-to-end P2MP topology between
the Root PE and the Leaf PEs, the failure reporting and processing
procedures are implemented only on the edge nodes.
Failure events may cause one or more Leaf PEs to become detached from
the PW tree. These events MUST be reported to the Root PE, using
appropriate out-of-band or in-band Operations, Administration, and
Maintenance (OAM) messages for monitoring.
It MUST be possible for the operator to choose the out-of-band or in-
band monitoring tools or both to monitor the Leaf PE status. For
management purposes, the solution SHOULD allow the Root PE to be
informed of Leaf PEs' failure.
Based on these failure notifications, solutions MUST allow the Root
PE to update the remaining leaves of the PW tree.
- A solution MUST support an in-band status notification mechanism
to detect failures: unidirectional point-to-multipoint traffic
failure. This MUST be realized by enhancing existing unicast PW
methods, such as Virtual Circuit Connectivity Verification (VCCV)
for seamless and familiar operation as defined in [RFC5085].
- In case of failure, it MUST correctly report which Leaf PEs are
affected. This MUST be realized by enhancing existing PW methods,
such as LDP Status Notification. The notification message SHOULD
include the type of fault (P2MP PW, AC, or PSN tunnel).
- A Leaf PE MAY be notified of the status of the Root PE's AC.
- A solution MUST support OAM message mapping [RFC6310] at the Root
PE and Leaf PE if a failure is detected on the source CE.
3.4.6. Protection and Restoration
It is assumed that if recovery procedures are required, the P2MP PSN
tunnel will support standard MPLS-based recovery techniques. In that
case, a mechanism SHOULD be implemented to avoid race conditions
between recovery at the PSN level and recovery at the PW level.
An alternative protection scheme MAY rely on the PW layer.
Leaf PEs MAY be protected via a P2MP PW redundancy mechanism. In the
example depicted below, a standby P2MP PW is used to protect the
active P2MP PW. In that protection scheme, the AC at the Root PE
MUST serve both P2MP PWs. In this scenario, the criteria for
Jounay, et al. Informational [Page 11]
RFC 7338 P2MP PW Requirements September 2014
switching over SHOULD be defined, e.g., failure of one or all leaves
of the active P2MP PW will trigger switchover of the whole P2MP PW.
CE1
|
ROOT active PE1 standby
P2MP PW .../ \....P2MP PW
/ \
P2 P3
/ \ / \
/ \ / \
/ \ / \
LEAF PE4 PE5 PE6 PE7
| | | |
| \ / |
\ CE2 /
\ /
------CE3-----
Figure 3: Example of P2MP PW Redundancy for Protecting Leaf PEs
Note that some of the nodes/links in this figure can be physically
shared; this depends on the service provider policy of network
redundancy.
The Root PE MAY be protected via a P2MP PW redundancy mechanism. In
the example depicted below, a standby P2MP PW is used to protect the
active P2MP. A single AC at the Leaf PE MUST be used to attach the
CE to the primary and the standby P2MP PW. The Leaf PE MUST support
protection mechanisms in order to select the active P2MP PW.
CE1
/ \
| |
ROOT active PE1 PE2 standby
P2MP PW1 | | P2MP PW2
| |
P2 P3
/ \/ \
/ /\ \
/ / \ \
/ / \ \
LEAF PE4 PE5
| |
CE2 CE3
Figure 4: Example of P2MP PW Redundancy for Protecting Root PEs
Jounay, et al. Informational [Page 12]
RFC 7338 P2MP PW Requirements September 2014
3.4.7. Scalability
The solution SHOULD scale at worst linearly for message size, memory
requirements, and processing requirements, with the number of Leaf
PEs.
Increasing the number of P2MP PWs between a Root PE and a given set
of Leaf PEs SHOULD NOT cause the P router to increase the number of
entries in its forwarding table by the same or greater proportion.
Multiplexing P2MP PWs to P2MP PSN tunnels achieves this.
4. Backward Compatibility
Solutions MUST be backward compatible with current PW standards.
Solutions SHOULD utilize existing capability advertisement and
negotiation procedures for the PEs implementing P2MP PW endpoints.
The implementation of OAM mechanisms also implies the advertisement
of PE capabilities to support specific OAM features. The solution
MAY allow advertising P2MP PW OAM capabilities. A solution MUST NOT
allow a P2MP PW to be established to PEs that do not support P2MP PW
functionality. It MUST have a mechanism to report an error for
incompatible PEs.
In some cases, upstream traffic is needed from downstream CEs to
upstream CEs. The P2MP PW solution SHOULD allow a return path (i.e.,
from the Leaf PE to the Root PE) that provides upstream connectivity.
In particular, the same ACs MAY be shared between the downstream and
upstream directions. For downstream, a CE receives traffic
originated by the Root PE over its AC. For upstream, the CE MAY also
send traffic destined to the same Root PE over the same AC.
5. Security Considerations
The security requirements common to PW are raised in Section 11 of
[RFC3916]. P2MP PW is a variant of the initial P2P PW definition,
and those requirements (and the security considerations from
[RFC3985]) also apply. The security considerations from [RFC5920]
and [RFC6941] also apply to the IP/MPLS and MPLS-TP deployment
scenarios, respectively.
Some issues specifically due to P2MP topology need to be addressed in
the definition of the solution:
- The solution SHOULD provide means to protect the traffic delivered
to receivers (Integrity, Confidentiality, Endpoint
Authentication).
Jounay, et al. Informational [Page 13]
RFC 7338 P2MP PW Requirements September 2014
- The solution SHOULD support means to protect the P2MP PW as a
whole against attacks that would lead to any kind of denial of
service.
Specifically, safeguard mechanisms should be considered to avoid any
negative impact on the whole PW tree when any one receiver or any
group of receivers is attacked. Safeguard mechanisms for both the
data plane and the control plane need to be considered.
6. References
6.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC3916] Xiao, X., Ed., McPherson, D., Ed., and P. Pate, Ed.,
"Requirements for Pseudo-Wire Emulation Edge-to-Edge
(PWE3)", RFC 3916, September 2004.
[RFC3985] Bryant, S., Ed., and P. Pate, Ed., "Pseudo Wire Emulation
Edge-to-Edge (PWE3) Architecture", RFC 3985, March 2005.
[RFC4446] Martini, L., "IANA Allocations for Pseudowire Edge to
Edge Emulation (PWE3)", BCP 116, RFC 4446, April 2006.
[RFC5332] Eckert, T., Rosen, E., Ed., Aggarwal, R., and Y. Rekhter,
"MPLS Multicast Encapsulations", RFC 5332, August 2008.
[RFC5659] Bocci, M. and S. Bryant, "An Architecture for Multi-
Segment Pseudowire Emulation Edge-to-Edge", RFC 5659,
October 2009.
[RFC6310] Aissaoui, M., Busschbach, P., Martini, L., Morrow, M.,
Nadeau, T., and Y(J). Stein, "Pseudowire (PW) Operations,
Administration, and Maintenance (OAM) Message Mapping",
RFC 6310, July 2011.
6.2. Informative References
[RFC4023] Worster, T., Rekhter, Y., and E. Rosen, Ed.,
"Encapsulating MPLS in IP or Generic Routing
Encapsulation (GRE)", RFC 4023, March 2005.
[RFC4461] Yasukawa, S., Ed., "Signaling Requirements for Point-to-
Multipoint Traffic-Engineered MPLS Label Switched Paths
(LSPs)", RFC 4461, April 2006.
Jounay, et al. Informational [Page 14]
RFC 7338 P2MP PW Requirements September 2014
[RFC4875] Aggarwal, R., Ed., Papadimitriou, D., Ed., and S.
Yasukawa, Ed., "Extensions to Resource Reservation
Protocol - Traffic Engineering (RSVP-TE) for Point-to-
Multipoint TE Label Switched Paths (LSPs)", RFC 4875, May
2007.
[RFC5085] Nadeau, T., Ed., and C. Pignataro, Ed., "Pseudowire
Virtual Circuit Connectivity Verification (VCCV): A
Control Channel for Pseudowires", RFC 5085, December
2007.
[RFC5254] Bitar, N., Ed., Bocci, M., Ed., and L. Martini, Ed.,
"Requirements for Multi-Segment Pseudowire Emulation
Edge-to-Edge (PWE3)", RFC 5254, October 2008.
[RFC5331] Aggarwal, R., Rekhter, Y., and E. Rosen, "MPLS Upstream
Label Assignment and Context-Specific Label Space", RFC
5331, August 2008.
[RFC5920] Fang, L., Ed., "Security Framework for MPLS and GMPLS
Networks", RFC 5920, July 2010.
[RFC6388] Wijnands, IJ., Ed., Minei, I., Ed., Kompella, K., and B.
Thomas, "Label Distribution Protocol Extensions for
Point-to-Multipoint and Multipoint-to-Multipoint Label
Switched Paths", RFC 6388, November 2011.
[RFC6941] Fang, L., Ed., Niven-Jenkins, B., Ed., Mansfield, S.,
Ed., and R. Graveman, Ed., "MPLS Transport Profile
(MPLS-TP) Security Framework", RFC 6941, April 2013.
[VPMS-REQS] Kamite, Y., Jounay, F., Niven-Jenkins, B., Brungard, D.,
and L. Jin, "Framework and Requirements for Virtual
Private Multicast Service (VPMS)", Work in Progress,
October 2012.
7. Acknowledgments
The authors thank the following people: the authors of [RFC4461]
since the structure and content of this document were, for some
sections, largely inspired by [RFC4461]; JL. Le Roux and A. Cauvin
for the discussions, comments, and support; Adrian Farrel for his
Routing Area Director review; and IESG reviewers.
Jounay, et al. Informational [Page 15]
RFC 7338 P2MP PW Requirements September 2014
8. Contributors
Philippe Niger
France Telecom
2, avenue Pierre-Marzin
22307 Lannion Cedex
France
EMail: philippe.niger@orange-ftgroup.com
Luca Martini
Cisco Systems, Inc.
9155 East Nichols Avenue, Suite 400
Englewood, CO 80112
US
EMail: lmartini@cisco.com
Lei Wang
Telenor
Snaroyveien 30
Fornebu 1331
Norway
EMail: lei.wang@telenor.com
Rahul Aggarwal
Juniper Networks
1194 North Mathilda Ave.
Sunnyvale, CA 94089
US
EMail: rahul@juniper.net
Simon Delord
Telstra
380 Flinders Lane
Melbourne
Australia
EMail: simon.delord@gmail.com
Jounay, et al. Informational [Page 16]
RFC 7338 P2MP PW Requirements September 2014
Martin Vigoureux
Alcatel-Lucent France
Route de Villejust
91620 Nozay
France
EMail: martin.vigoureux@alcatel-lucent.fr
Lizhong Jin
ZTE Corporation
889, Bibo Road
Shanghai, 201203
China
EMail: lizho.jin@gmail.com
Jounay, et al. Informational [Page 17]
RFC 7338 P2MP PW Requirements September 2014
Authors' Addresses
Frederic Jounay (editor)
Orange CH
4 rue caudray 1020 Renens
Switzerland
EMail: frederic.jounay@orange.ch
Yuji Kamite (editor)
NTT Communications Corporation
1-1-6 Uchisaiwai-cho, Chiyoda-ku
Tokyo 100-8019
Japan
EMail: y.kamite@ntt.com
Giles Heron
Cisco Systems, Inc.
9 New Square
Bedfont Lakes
Feltham
Middlesex
TW14 8HA
United Kingdom
EMail: giheron@cisco.com
Matthew Bocci
Alcatel-Lucent Telecom Ltd
Voyager Place
Shoppenhangers Road
Maidenhead
Berks
United Kingdom
EMail: Matthew.Bocci@alcatel-lucent.com
Jounay, et al. Informational [Page 18]