patch-2.4.4 linux/arch/mips/ddb5476/setup.c

• Lines: 376
• Date: Fri Apr 13 20:26:07 2001
• Orig file: v2.4.3/linux/arch/mips/ddb5476/setup.c
• Orig date: Wed Dec 31 16:00:00 1969

diff -u --recursive --new-file v2.4.3/linux/arch/mips/ddb5476/setup.c linux/arch/mips/ddb5476/setup.c
@@ -0,0 +1,375 @@
+/*
+ *  arch/mips/ddb5476/setup.c -- NEC DDB Vrc-5476 setup routines
+ *
+ *  Copyright (C) 2000 Geert Uytterhoeven <geert@sonycom.com>
+ *                     Sony Software Development Center Europe (SDCE), Brussels
+ */
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/kbd_ll.h>
+#include <linux/kernel.h>
+#include <linux/kdev_t.h>
+#include <linux/types.h>
+#include <linux/console.h>
+#include <linux/sched.h>
+#include <linux/mc146818rtc.h>
+#include <linux/pc_keyb.h>
+#include <linux/pci.h>
+#include <linux/ide.h>
+
+#include <asm/addrspace.h>
+#include <asm/bcache.h>
+#include <asm/keyboard.h>
+#include <asm/irq.h>
+#include <asm/reboot.h>
+#include <asm/gdb-stub.h>
+#include <asm/nile4.h>
+
+
+#ifdef CONFIG_REMOTE_DEBUG
+extern void rs_kgdb_hook(int);
+extern void breakpoint(void);
+#endif
+
+#if defined(CONFIG_SERIAL_CONSOLE)
+extern void console_setup(char *);
+#endif
+
+extern struct ide_ops std_ide_ops;
+extern struct rtc_ops ddb_rtc_ops;
+extern struct kbd_ops std_kbd_ops;
+
+static void (*back_to_prom) (void) = (void (*)(void)) 0xbfc00000;
+
+static void ddb_machine_restart(char *command)
+{
+	u32 t;
+
+	/* PCI cold reset */
+	t = nile4_in32(NILE4_PCICTRL + 4);
+	t |= 0x40000000;
+	nile4_out32(NILE4_PCICTRL + 4, t);
+	/* CPU cold reset */
+	t = nile4_in32(NILE4_CPUSTAT);
+	t |= 1;
+	nile4_out32(NILE4_CPUSTAT, t);
+	/* Call the PROM */
+	back_to_prom();
+}
+
+static void ddb_machine_halt(void)
+{
+	printk("DDB Vrc-5476 halted.\n");
+	while (1);
+}
+
+static void ddb_machine_power_off(void)
+{
+	printk("DDB Vrc-5476 halted. Please turn off the power.\n");
+	while (1);
+}
+
+extern void ddb_irq_setup(void);
+
+void (*board_time_init) (struct irqaction * irq);
+
+
+static void __init ddb_time_init(struct irqaction *irq)
+{
+	/* set the clock to 1 Hz */
+	nile4_out32(NILE4_T2CTRL, 1000000);
+	/* enable the General-Purpose Timer */
+	nile4_out32(NILE4_T2CTRL + 4, 0x00000001);
+	/* reset timer */
+	nile4_out32(NILE4_T2CNTR, 0);
+	/* enable interrupt */
+	nile4_enable_irq(NILE4_INT_GPT);
+	i8259_setup_irq(nile4_to_irq(NILE4_INT_GPT), irq);
+}
+
+static struct {
+	struct resource dma1;
+	struct resource pic1;
+	struct resource timer;
+	struct resource rtc;
+	struct resource dma_page_reg;
+	struct resource pic2;
+	struct resource dma2;
+} ddb5476_ioport = {
+	{
+	"dma1", 0x00, 0x1f, IORESOURCE_BUSY}, {
+	"pic1", 0x20, 0x3f, IORESOURCE_BUSY}, {
+	"timer", 0x40, 0x5f, IORESOURCE_BUSY}, {
+	"rtc", 0x70, 0x7f, IORESOURCE_BUSY}, {
+	"dma page reg", 0x80, 0x8f, IORESOURCE_BUSY}, {
+	"pic2", 0xa0, 0xbf, IORESOURCE_BUSY}, {
+	"dma2", 0xc0, 0xdf, IORESOURCE_BUSY}
+};
+
+static struct {
+	struct resource nile4;
+} ddb5476_iomem = {
+	{ "Nile 4", NILE4_BASE, NILE4_BASE + NILE4_SIZE - 1, IORESOURCE_BUSY}
+};
+
+void __init ddb_setup(void)
+{
+	extern int panic_timeout;
+
+	irq_setup = ddb_irq_setup;
+	mips_io_port_base = NILE4_PCI_IO_BASE;
+	isa_slot_offset = NILE4_PCI_MEM_BASE;
+	board_time_init = ddb_time_init;
+
+	_machine_restart = ddb_machine_restart;
+	_machine_halt = ddb_machine_halt;
+	_machine_power_off = ddb_machine_power_off;
+
+	/* request io port/mem resources  */
+	if (request_resource(&ioport_resource, &ddb5476_ioport.dma1) ||
+	    request_resource(&ioport_resource, &ddb5476_ioport.pic1) ||
+	    request_resource(&ioport_resource, &ddb5476_ioport.timer) ||
+	    request_resource(&ioport_resource, &ddb5476_ioport.rtc) ||
+	    request_resource(&ioport_resource,
+			     &ddb5476_ioport.dma_page_reg)
+	    || request_resource(&ioport_resource, &ddb5476_ioport.pic2)
+	    || request_resource(&ioport_resource, &ddb5476_ioport.dma2)
+	    || request_resource(&iomem_resource, &ddb5476_iomem.nile4)) {
+		printk
+		    ("ddb_setup - requesting oo port resources failed.\n");
+		for (;;);
+	}
+#ifdef CONFIG_BLK_DEV_IDE
+	ide_ops = &std_ide_ops;
+#endif
+	rtc_ops = &ddb_rtc_ops;
+
+#ifdef CONFIG_PC_KEYB
+	kbd_ops = &std_kbd_ops;
+#endif
+
+	/* Reboot on panic */
+	panic_timeout = 180;
+
+	/* [jsun] we need to set BAR0 so that SDRAM 0 appears at 0x0 in PCI */
+	/* *(long*)0xbfa00218 = 0x8; */
+
+#ifdef CONFIG_FB
+	conswitchp = &dummy_con;
+#endif
+
+
+	/* board initialization stuff - non-fundamental, but need to be set
+	 * before kernel runs */
+
+	/* setup I/O space */
+	nile4_set_pdar(NILE4_PCIW0,
+		       PHYSADDR(NILE4_PCI_IO_BASE), 0x02000000, 32, 0, 0);
+	nile4_set_pmr(NILE4_PCIINIT0, NILE4_PCICMD_IO, 0);
+
+	/* map config space to 0xa8000000, 128MB */
+	nile4_set_pdar(NILE4_PCIW1,
+		       PHYSADDR(NILE4_PCI_CFG_BASE), 0x08000000, 32, 0, 0);
+	nile4_set_pmr(NILE4_PCIINIT1, NILE4_PCICMD_CFG, 0x0);
+
+	/* ----- M1543 PCI setup ------ */
+
+	/* we know M1543 PCI-ISA controller is at addr:18 */
+	/* xxxx1010 makes USB at addr:13 and PMU at addr:14 */
+	*(volatile unsigned char *) 0xa8040072 &= 0xf0;
+	*(volatile unsigned char *) 0xa8040072 |= 0xa;
+
+	/* setup USB interrupt to IRQ 9, (bit 0:3 - 0001)
+	 * no IOCHRDY signal, (bit 7 - 1)
+	 * M1543C & M7101 VID and Subsys Device ID are read-only (bit 6 - 1)
+	 * Bypass USB Master INTAJ level to edge conversion (bit 4 - 0)
+	 */
+	*(unsigned char *) 0xa8040074 = 0xc1;
+
+	/* setup PMU(SCI to IRQ 10 (bit 0:3 - 0011)
+	 * SCI routing to IRQ 13 disabled (bit 7 - 1)
+	 * SCI interrupt level to edge conversion bypassed (bit 4 - 0)
+	 */
+	*(unsigned char *) 0xa8040076 = 0x83;
+
+	/* setup IDE controller
+	 * enable IDE controller (bit 6 - 1)
+	 * IDE IDSEL to be addr:24 (bit 4:5 - 11)
+	 * no IDE ATA Secondary Bus Signal Pad Control (bit 3 - 0)
+	 * no IDE ATA Primary Bus Signal Pad Control (bit 2 - 0)
+	 * primary IRQ is 14, secondary is 15 (bit 1:0 - 01
+	 */
+	// *(unsigned char*)0xa8040058 = 0x71;
+	// *(unsigned char*)0xa8040058 = 0x79;
+	// *(unsigned char*)0xa8040058 = 0x74;              // use SIRQ, primary tri-state
+	*(unsigned char *) 0xa8040058 = 0x75;	// primary tri-state
+
+#if 0
+	/* this is not necessary if M5229 does not use SIRQ */
+	*(unsigned char *) 0xa8040044 = 0x0d;	// primary to IRQ 14
+	*(unsigned char *) 0xa8040075 = 0x0d;	// secondary to IRQ 14
+#endif
+
+	/* enable IDE in the M5229 config register 0x50 (bit 0 - 1) */
+	/* M5229 IDSEL is addr:24; see above setting */
+	*(unsigned char *) 0xa9000050 |= 0x1;
+
+	/* enable bus master (bit 2)  and IO decoding  (bit 0) */
+	*(unsigned char *) 0xa9000004 |= 0x5;
+
+	/* enable native, copied from arch/ppc/k2boot/head.S */
+	/* TODO - need volatile, need to be portable */
+	*(unsigned char *) 0xa9000009 = 0xff;
+
+	/* ----- end of M1543 PCI setup ------ */
+
+	/* ----- reset on-board ether chip  ------ */
+	*((volatile u32 *) 0xa8020004) |= 1;	/* decode I/O */
+	*((volatile u32 *) 0xa8020010) = 0;	/* set BAR address */
+
+	/* send reset command */
+	*((volatile u32 *) 0xa6000000) = 1;	/* do a soft reset */
+
+	/* disable ether chip */
+	*((volatile u32 *) 0xa8020004) = 0;	/* disable any decoding */
+
+	/* put it into sleep */
+	*((volatile u32 *) 0xa8020040) = 0x80000000;
+
+	/* ----- end of reset on-board ether chip  ------ */
+
+	/* ----- set pci window 1 to pci memory space -------- */
+	nile4_set_pdar(NILE4_PCIW1,
+		       PHYSADDR(NILE4_PCI_MEM_BASE), 0x08000000, 32, 0, 0);
+	// nile4_set_pmr(NILE4_PCIINIT1, NILE4_PCICMD_MEM, 0);
+	nile4_set_pmr(NILE4_PCIINIT1, NILE4_PCICMD_MEM, 0x08000000);
+
+}
+
+#define USE_NILE4_SERIAL	0
+
+#if USE_NILE4_SERIAL
+#define ns16550_in(reg)		nile4_in8((reg)*8)
+#define ns16550_out(reg, val)	nile4_out8((reg)*8, (val))
+#else
+#define NS16550_BASE		(NILE4_PCI_IO_BASE+0x03f8)
+static inline u8 ns16550_in(u32 reg)
+{
+	return *(volatile u8 *) (NS16550_BASE + reg);
+}
+
+static inline void ns16550_out(u32 reg, u8 val)
+{
+	*(volatile u8 *) (NS16550_BASE + reg) = val;
+}
+#endif
+
+#define NS16550_RBR		0
+#define NS16550_THR		0
+#define NS16550_DLL		0
+#define NS16550_IER		1
+#define NS16550_DLM		1
+#define NS16550_FCR		2
+#define NS16550_IIR		2
+#define NS16550_LCR		3
+#define NS16550_MCR		4
+#define NS16550_LSR		5
+#define NS16550_MSR		6
+#define NS16550_SCR		7
+
+#define NS16550_LSR_DR		0x01	/* Data ready */
+#define NS16550_LSR_OE		0x02	/* Overrun */
+#define NS16550_LSR_PE		0x04	/* Parity error */
+#define NS16550_LSR_FE		0x08	/* Framing error */
+#define NS16550_LSR_BI		0x10	/* Break */
+#define NS16550_LSR_THRE	0x20	/* Xmit holding register empty */
+#define NS16550_LSR_TEMT	0x40	/* Xmitter empty */
+#define NS16550_LSR_ERR		0x80	/* Error */
+
+
+void _serinit(void)
+{
+#if USE_NILE4_SERIAL
+	ns16550_out(NS16550_LCR, 0x80);
+	ns16550_out(NS16550_DLM, 0x00);
+	ns16550_out(NS16550_DLL, 0x36);	/* 9600 baud */
+	ns16550_out(NS16550_LCR, 0x00);
+	ns16550_out(NS16550_LCR, 0x03);
+	ns16550_out(NS16550_FCR, 0x47);
+#else
+	/* done by PMON */
+#endif
+}
+
+void _putc(char c)
+{
+	while (!(ns16550_in(NS16550_LSR) & NS16550_LSR_THRE));
+	ns16550_out(NS16550_THR, c);
+	if (c == '\n') {
+		while (!(ns16550_in(NS16550_LSR) & NS16550_LSR_THRE));
+		ns16550_out(NS16550_THR, '\r');
+	}
+}
+
+void _puts(const char *s)
+{
+	char c;
+
+	while ((c = *s++))
+		_putc(c);
+}
+
+char _getc(void)
+{
+	while (!(ns16550_in(NS16550_LSR) & NS16550_LSR_DR));
+
+	return ns16550_in(NS16550_RBR);
+}
+
+int _testc(void)
+{
+	return (ns16550_in(NS16550_LSR) & NS16550_LSR_DR) != 0;
+}
+
+
+/*
+ *  Hexadecimal 7-segment LED
+ */
+void ddb5476_led_hex(int hex)
+{
+	outb(hex, 0x80);
+}
+
+
+/*
+ *  LEDs D2 and D3, connected to the GPIO pins of the PMU in the ALi M1543
+ */
+struct pci_dev *pci_pmu = NULL;
+
+void ddb5476_led_d2(int on)
+{
+	u8 t;
+
+	if (pci_pmu) {
+		pci_read_config_byte(pci_pmu, 0x7e, &t);
+		if (on)
+			t &= 0x7f;
+		else
+			t |= 0x80;
+		pci_write_config_byte(pci_pmu, 0x7e, t);
+	}
+}
+
+void ddb5476_led_d3(int on)
+{
+	u8 t;
+
+	if (pci_pmu) {
+		pci_read_config_byte(pci_pmu, 0x7e, &t);
+		if (on)
+			t &= 0xbf;
+		else
+			t |= 0x40;
+		pci_write_config_byte(pci_pmu, 0x7e, t);
+	}
+}