patch-2.4.21 linux-2.4.21/drivers/net/starfire.c
Next file: linux-2.4.21/drivers/net/sun3_82586.c
Previous file: linux-2.4.21/drivers/net/smc9194.c
Back to the patch index
Back to the overall index
- Lines: 2252
- Date:
2003-06-13 07:51:35.000000000 -0700
- Orig file:
linux-2.4.20/drivers/net/starfire.c
- Orig date:
2002-08-02 17:39:44.000000000 -0700
diff -urN linux-2.4.20/drivers/net/starfire.c linux-2.4.21/drivers/net/starfire.c
@@ -101,15 +101,33 @@
- Better stats and error handling (Ion Badulescu)
- Use new pci_set_mwi() PCI API function (jgarzik)
-TODO:
- - implement tx_timeout() properly
+ LK1.3.7 (Ion Badulescu)
+ - minimal implementation of tx_timeout()
+ - correctly shutdown the Rx/Tx engines in netdev_close()
+ - added calls to netif_carrier_on/off
+ (patch from Stefan Rompf <srompf@isg.de>)
- VLAN support
+
+ LK1.3.8 (Ion Badulescu)
+ - adjust DMA burst size on sparc64
+ - 64-bit support
+ - reworked zerocopy support for 64-bit buffers
+ - working and usable interrupt mitigation/latency
+ - reduced Tx interrupt frequency for lower interrupt overhead
+
+ LK1.3.9 (Ion Badulescu)
+ - bugfix for mcast filter
+ - enable the right kind of Tx interrupts (TxDMADone, not TxDone)
+
+TODO:
+ - full NAPI support
*/
#define DRV_NAME "starfire"
-#define DRV_VERSION "1.03+LK1.3.6"
-#define DRV_RELDATE "March 7, 2002"
+#define DRV_VERSION "1.03+LK1.3.9"
+#define DRV_RELDATE "December 13, 2002"
+#include <linux/config.h>
#include <linux/version.h>
#include <linux/module.h>
#include <linux/kernel.h>
@@ -118,7 +136,6 @@
#include <linux/etherdevice.h>
#include <linux/init.h>
#include <linux/delay.h>
-#include <linux/crc32.h>
#include <asm/processor.h> /* Processor type for cache alignment. */
#include <asm/uaccess.h>
#include <asm/io.h>
@@ -154,11 +171,16 @@
#include "starfire_firmware.h"
#endif /* HAS_FIRMWARE */
+#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
+#define VLAN_SUPPORT
+#endif
+
/* The user-configurable values.
These may be modified when a driver module is loaded.*/
/* Used for tuning interrupt latency vs. overhead. */
-static int interrupt_mitigation;
+static int intr_latency;
+static int small_frames;
static int debug = 1; /* 1 normal messages, 0 quiet .. 7 verbose. */
static int max_interrupt_work = 20;
@@ -166,6 +188,12 @@
/* Maximum number of multicast addresses to filter (vs. rx-all-multicast).
The Starfire has a 512 element hash table based on the Ethernet CRC. */
static int multicast_filter_limit = 512;
+/* Whether to do TCP/UDP checksums in hardware */
+#ifdef HAS_FIRMWARE
+static int enable_hw_cksum = 1;
+#else
+static int enable_hw_cksum = 0;
+#endif
#define PKT_BUF_SZ 1536 /* Size of each temporary Rx buffer.*/
/*
@@ -178,7 +206,9 @@
* packets as the starfire doesn't allow for misaligned DMAs ;-(
* 23/10/2000 - Jes
*
- * The Alpha and the Sparc don't allow unaligned loads, either. -Ion
+ * The Alpha and the Sparc don't like unaligned loads, either. On Sparc64,
+ * at least, having unaligned frames leads to a rather serious performance
+ * penalty. -Ion
*/
#if defined(__ia64__) || defined(__alpha__) || defined(__sparc__)
static int rx_copybreak = PKT_BUF_SZ;
@@ -186,9 +216,17 @@
static int rx_copybreak /* = 0 */;
#endif
+/* PCI DMA burst size -- on sparc64 we want to force it to 64 bytes, on the others the default of 128 is fine. */
+#ifdef __sparc__
+#define DMA_BURST_SIZE 64
+#else
+#define DMA_BURST_SIZE 128
+#endif
+
/* Used to pass the media type, etc.
Both 'options[]' and 'full_duplex[]' exist for driver interoperability.
The media type is usually passed in 'options[]'.
+ These variables are deprecated, use ethtool instead. -Ion
*/
#define MAX_UNITS 8 /* More are supported, limit only on options */
static int options[MAX_UNITS] = {0, };
@@ -198,33 +236,55 @@
/* The "native" ring sizes are either 256 or 2048.
However in some modes a descriptor may be marked to wrap the ring earlier.
- The driver allocates a single page for each descriptor ring, constraining
- the maximum size in an architecture-dependent way.
*/
#define RX_RING_SIZE 256
#define TX_RING_SIZE 32
/* The completion queues are fixed at 1024 entries i.e. 4K or 8KB. */
#define DONE_Q_SIZE 1024
+/* All queues must be aligned on a 256-byte boundary */
+#define QUEUE_ALIGN 256
+
+#if RX_RING_SIZE > 256
+#define RX_Q_ENTRIES Rx2048QEntries
+#else
+#define RX_Q_ENTRIES Rx256QEntries
+#endif
/* Operational parameters that usually are not changed. */
/* Time in jiffies before concluding the transmitter is hung. */
#define TX_TIMEOUT (2 * HZ)
-#ifdef ZEROCOPY
-#if MAX_SKB_FRAGS <= 6
-#define MAX_STARFIRE_FRAGS 6
-#else /* MAX_STARFIRE_FRAGS > 6 */
-#warning This driver will not work with more than 6 skb fragments.
-#warning Turning off zerocopy support.
-#undef ZEROCOPY
-#endif /* MAX_STARFIRE_FRAGS > 6 */
-#endif /* ZEROCOPY */
+/*
+ * This SUCKS.
+ * We need a much better method to determine if dma_addr_t is 64-bit.
+ */
+#if (defined(__i386__) && defined(CONFIG_HIGHMEM) && (LINUX_VERSION_CODE > 0x20500 || defined(CONFIG_HIGHMEM64G))) || defined(__x86_64__) || defined (__ia64__) || defined(__mips64__) || (defined(__mips__) && defined(CONFIG_HIGHMEM) && defined(CONFIG_64BIT_PHYS_ADDR))
+/* 64-bit dma_addr_t */
+#define ADDR_64BITS /* This chip uses 64 bit addresses. */
+#define cpu_to_dma(x) cpu_to_le64(x)
+#define dma_to_cpu(x) le64_to_cpu(x)
+#define RX_DESC_Q_ADDR_SIZE RxDescQAddr64bit
+#define TX_DESC_Q_ADDR_SIZE TxDescQAddr64bit
+#define RX_COMPL_Q_ADDR_SIZE RxComplQAddr64bit
+#define TX_COMPL_Q_ADDR_SIZE TxComplQAddr64bit
+#define RX_DESC_ADDR_SIZE RxDescAddr64bit
+#else /* 32-bit dma_addr_t */
+#define cpu_to_dma(x) cpu_to_le32(x)
+#define dma_to_cpu(x) le32_to_cpu(x)
+#define RX_DESC_Q_ADDR_SIZE RxDescQAddr32bit
+#define TX_DESC_Q_ADDR_SIZE TxDescQAddr32bit
+#define RX_COMPL_Q_ADDR_SIZE RxComplQAddr32bit
+#define TX_COMPL_Q_ADDR_SIZE TxComplQAddr32bit
+#define RX_DESC_ADDR_SIZE RxDescAddr32bit
+#endif
-#ifdef ZEROCOPY
+#ifdef MAX_SKB_FRAGS
#define skb_first_frag_len(skb) skb_headlen(skb)
-#else /* not ZEROCOPY */
+#define skb_num_frags(skb) (skb_shinfo(skb)->nr_frags + 1)
+#else /* not MAX_SKB_FRAGS */
#define skb_first_frag_len(skb) (skb->len)
-#endif /* not ZEROCOPY */
+#define skb_num_frags(skb) 1
+#endif /* not MAX_SKB_FRAGS */
/* 2.2.x compatibility code */
#if LINUX_VERSION_CODE < 0x20300
@@ -233,9 +293,12 @@
#else /* LINUX_VERSION_CODE > 0x20300 */
+#include <linux/crc32.h>
#include <linux/ethtool.h>
#include <linux/mii.h>
+#include <linux/if_vlan.h>
+
#define COMPAT_MOD_INC_USE_COUNT
#define COMPAT_MOD_DEC_USE_COUNT
@@ -266,15 +329,20 @@
MODULE_PARM(mtu, "i");
MODULE_PARM(debug, "i");
MODULE_PARM(rx_copybreak, "i");
-MODULE_PARM(interrupt_mitigation, "i");
+MODULE_PARM(intr_latency, "i");
+MODULE_PARM(small_frames, "i");
MODULE_PARM(options, "1-" __MODULE_STRING(MAX_UNITS) "i");
MODULE_PARM(full_duplex, "1-" __MODULE_STRING(MAX_UNITS) "i");
-MODULE_PARM_DESC(max_interrupt_work, "Starfire maximum events handled per interrupt");
-MODULE_PARM_DESC(mtu, "Starfire MTU (all boards)");
-MODULE_PARM_DESC(debug, "Starfire debug level (0-6)");
-MODULE_PARM_DESC(rx_copybreak, "Starfire copy breakpoint for copy-only-tiny-frames");
-MODULE_PARM_DESC(options, "Starfire: Bits 0-3: media type, bit 17: full duplex");
-MODULE_PARM_DESC(full_duplex, "Starfire full duplex setting(s) (1)");
+MODULE_PARM(enable_hw_cksum, "i");
+MODULE_PARM_DESC(max_interrupt_work, "Maximum events handled per interrupt");
+MODULE_PARM_DESC(mtu, "MTU (all boards)");
+MODULE_PARM_DESC(debug, "Debug level (0-6)");
+MODULE_PARM_DESC(rx_copybreak, "Copy breakpoint for copy-only-tiny-frames");
+MODULE_PARM_DESC(intr_latency, "Maximum interrupt latency, in microseconds");
+MODULE_PARM_DESC(small_frames, "Maximum size of receive frames that bypass interrupt latency (0,64,128,256,512)");
+MODULE_PARM_DESC(options, "Deprecated: Bits 0-3: media type, bit 17: full duplex");
+MODULE_PARM_DESC(full_duplex, "Deprecated: Forced full-duplex setting (0/1)");
+MODULE_PARM_DESC(enable_hw_cksum, "Enable/disable hardware cksum support (0/1)");
/*
Theory of Operation
@@ -303,14 +371,14 @@
IIIb/c. Transmit/Receive Structure
See the Adaptec manual for the many possible structures, and options for
-each structure. There are far too many to document here.
+each structure. There are far too many to document all of them here.
For transmit this driver uses type 0/1 transmit descriptors (depending
-on the presence of the zerocopy infrastructure), and relies on automatic
+on the 32/64 bitness of the architecture), and relies on automatic
minimum-length padding. It does not use the completion queue
consumer index, but instead checks for non-zero status entries.
-For receive this driver uses type 0 receive descriptors. The driver
+For receive this driver uses type 0/1/2/3 receive descriptors. The driver
allocates full frame size skbuffs for the Rx ring buffers, so all frames
should fit in a single descriptor. The driver does not use the completion
queue consumer index, but instead checks for non-zero status entries.
@@ -335,15 +403,15 @@
dev->tbusy flag. The other thread is the interrupt handler, which is single
threaded by the hardware and interrupt handling software.
-The send packet thread has partial control over the Tx ring and 'dev->tbusy'
-flag. It sets the tbusy flag whenever it's queuing a Tx packet. If the next
-queue slot is empty, it clears the tbusy flag when finished otherwise it sets
-the 'lp->tx_full' flag.
+The send packet thread has partial control over the Tx ring and the netif_queue
+status. If the number of free Tx slots in the ring falls below a certain number
+(currently hardcoded to 4), it signals the upper layer to stop the queue.
The interrupt handler has exclusive control over the Rx ring and records stats
from the Tx ring. After reaping the stats, it marks the Tx queue entry as
-empty by incrementing the dirty_tx mark. Iff the 'lp->tx_full' flag is set, it
-clears both the tx_full and tbusy flags.
+empty by incrementing the dirty_tx mark. Iff the netif_queue is stopped and the
+number of free Tx slow is above the threshold, it signals the upper layer to
+restart the queue.
IV. Notes
@@ -355,18 +423,15 @@
IVc. Errata
+- StopOnPerr is broken, don't enable
+- Hardware ethernet padding exposes random data, perform software padding
+ instead (unverified -- works correctly for all the hardware I have)
+
*/
enum chip_capability_flags {CanHaveMII=1, };
-#define PCI_IOTYPE (PCI_USES_MASTER | PCI_USES_MEM | PCI_ADDR0)
-
-#if 0
-#define ADDR_64BITS 1 /* This chip uses 64 bit addresses. */
-#endif
-
-#define HAS_IP_COPYSUM 1
enum chipset {
CH_6915 = 0,
@@ -398,7 +463,7 @@
enum register_offsets {
PCIDeviceConfig=0x50040, GenCtrl=0x50070, IntrTimerCtrl=0x50074,
IntrClear=0x50080, IntrStatus=0x50084, IntrEnable=0x50088,
- MIICtrl=0x52000, StationAddr=0x50120, EEPROMCtrl=0x51000,
+ MIICtrl=0x52000, TxStationAddr=0x50120, EEPROMCtrl=0x51000,
GPIOCtrl=0x5008C, TxDescCtrl=0x50090,
TxRingPtr=0x50098, HiPriTxRingPtr=0x50094, /* Low and High priority. */
TxRingHiAddr=0x5009C, /* 64 bit address extension. */
@@ -409,11 +474,16 @@
CompletionQConsumerIdx=0x500C4, RxDMACtrl=0x500D0,
RxDescQCtrl=0x500D4, RxDescQHiAddr=0x500DC, RxDescQAddr=0x500E0,
RxDescQIdx=0x500E8, RxDMAStatus=0x500F0, RxFilterMode=0x500F4,
- TxMode=0x55000, PerfFilterTable=0x56000, HashTable=0x56100,
+ TxMode=0x55000, VlanType=0x55064,
+ PerfFilterTable=0x56000, HashTable=0x56100,
TxGfpMem=0x58000, RxGfpMem=0x5a000,
};
-/* Bits in the interrupt status/mask registers. */
+/*
+ * Bits in the interrupt status/mask registers.
+ * Warning: setting Intr[Ab]NormalSummary in the IntrEnable register
+ * enables all the interrupt sources that are or'ed into those status bits.
+ */
enum intr_status_bits {
IntrLinkChange=0xf0000000, IntrStatsMax=0x08000000,
IntrAbnormalSummary=0x02000000, IntrGeneralTimer=0x01000000,
@@ -438,7 +508,16 @@
/* Bits in the RxFilterMode register. */
enum rx_mode_bits {
AcceptBroadcast=0x04, AcceptAllMulticast=0x02, AcceptAll=0x01,
- AcceptMulticast=0x10, AcceptMyPhys=0xE040,
+ AcceptMulticast=0x10, PerfectFilter=0x40, HashFilter=0x30,
+ PerfectFilterVlan=0x80, MinVLANPrio=0xE000, VlanMode=0x0200,
+ WakeupOnGFP=0x0800,
+};
+
+/* Bits in the TxMode register */
+enum tx_mode_bits {
+ MiiSoftReset=0x8000, MIILoopback=0x4000,
+ TxFlowEnable=0x0800, RxFlowEnable=0x0400,
+ PadEnable=0x04, FullDuplex=0x02, HugeFrame=0x01,
};
/* Bits in the TxDescCtrl register. */
@@ -447,7 +526,8 @@
TxDescSpace128=0x30, TxDescSpace256=0x40,
TxDescType0=0x00, TxDescType1=0x01, TxDescType2=0x02,
TxDescType3=0x03, TxDescType4=0x04,
- TxNoDMACompletion=0x08, TxDescQ64bit=0x80,
+ TxNoDMACompletion=0x08,
+ TxDescQAddr64bit=0x80, TxDescQAddr32bit=0,
TxHiPriFIFOThreshShift=24, TxPadLenShift=16,
TxDMABurstSizeShift=8,
};
@@ -455,81 +535,144 @@
/* Bits in the RxDescQCtrl register. */
enum rx_ctrl_bits {
RxBufferLenShift=16, RxMinDescrThreshShift=0,
- RxPrefetchMode=0x8000, Rx2048QEntries=0x4000,
- RxVariableQ=0x2000, RxDesc64bit=0x1000,
- RxDescQAddr64bit=0x0100,
+ RxPrefetchMode=0x8000, RxVariableQ=0x2000,
+ Rx2048QEntries=0x4000, Rx256QEntries=0,
+ RxDescAddr64bit=0x1000, RxDescAddr32bit=0,
+ RxDescQAddr64bit=0x0100, RxDescQAddr32bit=0,
RxDescSpace4=0x000, RxDescSpace8=0x100,
RxDescSpace16=0x200, RxDescSpace32=0x300,
RxDescSpace64=0x400, RxDescSpace128=0x500,
RxConsumerWrEn=0x80,
};
+/* Bits in the RxDMACtrl register. */
+enum rx_dmactrl_bits {
+ RxReportBadFrames=0x80000000, RxDMAShortFrames=0x40000000,
+ RxDMABadFrames=0x20000000, RxDMACrcErrorFrames=0x10000000,
+ RxDMAControlFrame=0x08000000, RxDMAPauseFrame=0x04000000,
+ RxChecksumIgnore=0, RxChecksumRejectTCPUDP=0x02000000,
+ RxChecksumRejectTCPOnly=0x01000000,
+ RxCompletionQ2Enable=0x800000,
+ RxDMAQ2Disable=0, RxDMAQ2FPOnly=0x100000,
+ RxDMAQ2SmallPkt=0x200000, RxDMAQ2HighPrio=0x300000,
+ RxDMAQ2NonIP=0x400000,
+ RxUseBackupQueue=0x080000, RxDMACRC=0x040000,
+ RxEarlyIntThreshShift=12, RxHighPrioThreshShift=8,
+ RxBurstSizeShift=0,
+};
+
/* Bits in the RxCompletionAddr register */
enum rx_compl_bits {
- RxComplQAddr64bit=0x80, TxComplProducerWrEn=0x40,
+ RxComplQAddr64bit=0x80, RxComplQAddr32bit=0,
+ RxComplProducerWrEn=0x40,
RxComplType0=0x00, RxComplType1=0x10,
RxComplType2=0x20, RxComplType3=0x30,
RxComplThreshShift=0,
};
+/* Bits in the TxCompletionAddr register */
+enum tx_compl_bits {
+ TxComplQAddr64bit=0x80, TxComplQAddr32bit=0,
+ TxComplProducerWrEn=0x40,
+ TxComplIntrStatus=0x20,
+ CommonQueueMode=0x10,
+ TxComplThreshShift=0,
+};
+
+/* Bits in the GenCtrl register */
+enum gen_ctrl_bits {
+ RxEnable=0x05, TxEnable=0x0a,
+ RxGFPEnable=0x10, TxGFPEnable=0x20,
+};
+
+/* Bits in the IntrTimerCtrl register */
+enum intr_ctrl_bits {
+ Timer10X=0x800, EnableIntrMasking=0x60, SmallFrameBypass=0x100,
+ SmallFrame64=0, SmallFrame128=0x200, SmallFrame256=0x400, SmallFrame512=0x600,
+ IntrLatencyMask=0x1f,
+};
+
/* The Rx and Tx buffer descriptors. */
struct starfire_rx_desc {
- u32 rxaddr; /* Optionally 64 bits. */
+ dma_addr_t rxaddr;
};
enum rx_desc_bits {
RxDescValid=1, RxDescEndRing=2,
};
-/* Completion queue entry.
- You must update the page allocation, init_ring and the shift count in rx()
- if using a larger format. */
-#ifdef HAS_FIRMWARE
-#define csum_rx_status
-#endif /* HAS_FIRMWARE */
-struct rx_done_desc {
+/* Completion queue entry. */
+struct short_rx_done_desc {
+ u32 status; /* Low 16 bits is length. */
+};
+struct basic_rx_done_desc {
u32 status; /* Low 16 bits is length. */
-#ifdef csum_rx_status
- u32 status2; /* Low 16 bits is csum */
-#endif /* csum_rx_status */
-#ifdef full_rx_status
- u32 status2;
+ u16 vlanid;
+ u16 status2;
+};
+struct csum_rx_done_desc {
+ u32 status; /* Low 16 bits is length. */
+ u16 csum; /* Partial checksum */
+ u16 status2;
+};
+struct full_rx_done_desc {
+ u32 status; /* Low 16 bits is length. */
+ u16 status3;
+ u16 status2;
u16 vlanid;
u16 csum; /* partial checksum */
u32 timestamp;
-#endif /* full_rx_status */
};
+/* XXX: this is ugly and I'm not sure it's worth the trouble -Ion */
+#ifdef HAS_FIRMWARE
+#ifdef VLAN_SUPPORT
+typedef struct full_rx_done_desc rx_done_desc;
+#define RxComplType RxComplType3
+#else /* not VLAN_SUPPORT */
+typedef struct csum_rx_done_desc rx_done_desc;
+#define RxComplType RxComplType2
+#endif /* not VLAN_SUPPORT */
+#else /* not HAS_FIRMWARE */
+#ifdef VLAN_SUPPORT
+typedef struct basic_rx_done_desc rx_done_desc;
+#define RxComplType RxComplType1
+#else /* not VLAN_SUPPORT */
+typedef struct short_rx_done_desc rx_done_desc;
+#define RxComplType RxComplType0
+#endif /* not VLAN_SUPPORT */
+#endif /* not HAS_FIRMWARE */
+
enum rx_done_bits {
RxOK=0x20000000, RxFIFOErr=0x10000000, RxBufQ2=0x08000000,
};
-#ifdef ZEROCOPY
-/* Type 0 Tx descriptor. */
-/* If more fragments are needed, don't forget to change the
- descriptor spacing as well! */
-struct starfire_tx_desc {
- u32 status;
- u32 nbufs;
- u32 first_addr;
- u16 first_len;
- u16 total_len;
- struct {
- u32 addr;
- u32 len;
- } frag[MAX_STARFIRE_FRAGS];
-};
-#else /* not ZEROCOPY */
/* Type 1 Tx descriptor. */
-struct starfire_tx_desc {
+struct starfire_tx_desc_1 {
u32 status; /* Upper bits are status, lower 16 length. */
- u32 first_addr;
+ u32 addr;
};
-#endif /* not ZEROCOPY */
+
+/* Type 2 Tx descriptor. */
+struct starfire_tx_desc_2 {
+ u32 status; /* Upper bits are status, lower 16 length. */
+ u32 reserved;
+ u64 addr;
+};
+
+#ifdef ADDR_64BITS
+typedef struct starfire_tx_desc_2 starfire_tx_desc;
+#define TX_DESC_TYPE TxDescType2
+#else /* not ADDR_64BITS */
+typedef struct starfire_tx_desc_1 starfire_tx_desc;
+#define TX_DESC_TYPE TxDescType1
+#endif /* not ADDR_64BITS */
+#define TX_DESC_SPACING TxDescSpaceUnlim
+
enum tx_desc_bits {
TxDescID=0xB0000000,
TxCRCEn=0x01000000, TxDescIntr=0x08000000,
TxRingWrap=0x04000000, TxCalTCP=0x02000000,
};
-struct tx_done_report {
+struct tx_done_desc {
u32 status; /* timestamp, index. */
#if 0
u32 intrstatus; /* interrupt status */
@@ -542,45 +685,48 @@
};
struct tx_ring_info {
struct sk_buff *skb;
- dma_addr_t first_mapping;
-#ifdef ZEROCOPY
- dma_addr_t frag_mapping[MAX_STARFIRE_FRAGS];
-#endif /* ZEROCOPY */
+ dma_addr_t mapping;
+ unsigned int used_slots;
};
#define PHY_CNT 2
struct netdev_private {
/* Descriptor rings first for alignment. */
struct starfire_rx_desc *rx_ring;
- struct starfire_tx_desc *tx_ring;
+ starfire_tx_desc *tx_ring;
dma_addr_t rx_ring_dma;
dma_addr_t tx_ring_dma;
/* The addresses of rx/tx-in-place skbuffs. */
struct rx_ring_info rx_info[RX_RING_SIZE];
struct tx_ring_info tx_info[TX_RING_SIZE];
/* Pointers to completion queues (full pages). */
- struct rx_done_desc *rx_done_q;
+ rx_done_desc *rx_done_q;
dma_addr_t rx_done_q_dma;
unsigned int rx_done;
- struct tx_done_report *tx_done_q;
+ struct tx_done_desc *tx_done_q;
dma_addr_t tx_done_q_dma;
unsigned int tx_done;
struct net_device_stats stats;
struct pci_dev *pci_dev;
+#ifdef VLAN_SUPPORT
+ struct vlan_group *vlgrp;
+#endif
+ void *queue_mem;
+ dma_addr_t queue_mem_dma;
+ size_t queue_mem_size;
+
/* Frequently used values: keep some adjacent for cache effect. */
+ spinlock_t lock;
unsigned int cur_rx, dirty_rx; /* Producer/consumer ring indices */
- unsigned int cur_tx, dirty_tx;
+ unsigned int cur_tx, dirty_tx, reap_tx;
unsigned int rx_buf_sz; /* Based on MTU+slack. */
- unsigned int tx_full:1, /* The Tx queue is full. */
/* These values keep track of the transceiver/media in use. */
- autoneg:1, /* Autonegotiation allowed. */
- full_duplex:1, /* Full-duplex operation. */
- speed100:1; /* Set if speed == 100MBit. */
- unsigned int intr_mitigation;
+ int speed100; /* Set if speed == 100MBit. */
u32 tx_mode;
+ u32 intr_timer_ctrl;
u8 tx_threshold;
/* MII transceiver section. */
- u16 advertising; /* NWay media advertisement */
+ struct mii_if_info mii_if; /* MII lib hooks/info */
int phy_cnt; /* MII device addresses. */
unsigned char phys[PHY_CNT]; /* MII device addresses. */
};
@@ -604,6 +750,44 @@
static void netdev_media_change(struct net_device *dev);
+#ifdef VLAN_SUPPORT
+static void netdev_vlan_rx_register(struct net_device *dev, struct vlan_group *grp)
+{
+ struct netdev_private *np = dev->priv;
+
+ spin_lock(&np->lock);
+ if (debug > 2)
+ printk("%s: Setting vlgrp to %p\n", dev->name, grp);
+ np->vlgrp = grp;
+ set_rx_mode(dev);
+ spin_unlock(&np->lock);
+}
+
+static void netdev_vlan_rx_add_vid(struct net_device *dev, unsigned short vid)
+{
+ struct netdev_private *np = dev->priv;
+
+ spin_lock(&np->lock);
+ if (debug > 1)
+ printk("%s: Adding vlanid %d to vlan filter\n", dev->name, vid);
+ set_rx_mode(dev);
+ spin_unlock(&np->lock);
+}
+
+static void netdev_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid)
+{
+ struct netdev_private *np = dev->priv;
+
+ spin_lock(&np->lock);
+ if (debug > 1)
+ printk("%s: removing vlanid %d from vlan filter\n", dev->name, vid);
+ if (np->vlgrp)
+ np->vlgrp->vlan_devices[vid] = NULL;
+ set_rx_mode(dev);
+ spin_unlock(&np->lock);
+}
+#endif /* VLAN_SUPPORT */
+
static int __devinit starfire_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
@@ -615,10 +799,6 @@
long ioaddr;
int drv_flags, io_size;
int boguscnt;
-#ifndef HAVE_PCI_SET_MWI
- u16 cmd;
- u8 cache;
-#endif
/* when built into the kernel, we only print version if device is found */
#ifndef MODULE
@@ -635,13 +815,13 @@
ioaddr = pci_resource_start(pdev, 0);
io_size = pci_resource_len(pdev, 0);
if (!ioaddr || ((pci_resource_flags(pdev, 0) & IORESOURCE_MEM) == 0)) {
- printk (KERN_ERR DRV_NAME " %d: no PCI MEM resources, aborting\n", card_idx);
+ printk(KERN_ERR DRV_NAME " %d: no PCI MEM resources, aborting\n", card_idx);
return -ENODEV;
}
dev = alloc_etherdev(sizeof(*np));
if (!dev) {
- printk (KERN_ERR DRV_NAME " %d: cannot alloc etherdev, aborting\n", card_idx);
+ printk(KERN_ERR DRV_NAME " %d: cannot alloc etherdev, aborting\n", card_idx);
return -ENOMEM;
}
SET_MODULE_OWNER(dev);
@@ -649,7 +829,7 @@
irq = pdev->irq;
if (pci_request_regions (pdev, dev->name)) {
- printk (KERN_ERR DRV_NAME " %d: cannot reserve PCI resources, aborting\n", card_idx);
+ printk(KERN_ERR DRV_NAME " %d: cannot reserve PCI resources, aborting\n", card_idx);
goto err_out_free_netdev;
}
@@ -657,7 +837,7 @@
#if !defined(CONFIG_SPARC64) || LINUX_VERSION_CODE > 0x20300
ioaddr = (long) ioremap(ioaddr, io_size);
if (!ioaddr) {
- printk (KERN_ERR DRV_NAME " %d: cannot remap 0x%x @ 0x%lx, aborting\n",
+ printk(KERN_ERR DRV_NAME " %d: cannot remap %#x @ %#lx, aborting\n",
card_idx, io_size, ioaddr);
goto err_out_free_res;
}
@@ -665,29 +845,26 @@
pci_set_master(pdev);
-#ifdef HAVE_PCI_SET_MWI
- pci_set_mwi(pdev);
-#else
/* enable MWI -- it vastly improves Rx performance on sparc64 */
- pci_read_config_word(pdev, PCI_COMMAND, &cmd);
- cmd |= PCI_COMMAND_INVALIDATE;
- pci_write_config_word(pdev, PCI_COMMAND, cmd);
-
- /* set PCI cache size */
- pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &cache);
- if ((cache << 2) != SMP_CACHE_BYTES) {
- printk(KERN_INFO " PCI cache line size set incorrectly "
- "(%i bytes) by BIOS/FW, correcting to %i\n",
- (cache << 2), SMP_CACHE_BYTES);
- pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE,
- SMP_CACHE_BYTES >> 2);
- }
-#endif
+ pci_set_mwi(pdev);
+#ifdef MAX_SKB_FRAGS
+ dev->features |= NETIF_F_SG;
+#endif /* MAX_SKB_FRAGS */
#ifdef ZEROCOPY
- /* Starfire can do SG and TCP/UDP checksumming */
- dev->features |= NETIF_F_SG | NETIF_F_IP_CSUM;
+ /* Starfire can do TCP/UDP checksumming */
+ if (enable_hw_cksum)
+ dev->features |= NETIF_F_IP_CSUM;
#endif /* ZEROCOPY */
+#ifdef VLAN_SUPPORT
+ dev->features |= NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_FILTER;
+ dev->vlan_rx_register = netdev_vlan_rx_register;
+ dev->vlan_rx_add_vid = netdev_vlan_rx_add_vid;
+ dev->vlan_rx_kill_vid = netdev_vlan_rx_kill_vid;
+#endif /* VLAN_RX_KILL_VID */
+#ifdef ADDR_64BITS
+ dev->features |= NETIF_F_HIGHDMA;
+#endif /* ADDR_64BITS */
/* Serial EEPROM reads are hidden by the hardware. */
for (i = 0; i < 6; i++)
@@ -702,7 +879,7 @@
#endif
/* Issue soft reset */
- writel(0x8000, ioaddr + TxMode);
+ writel(MiiSoftReset, ioaddr + TxMode);
udelay(1000);
writel(0, ioaddr + TxMode);
@@ -723,9 +900,17 @@
dev->irq = irq;
np = dev->priv;
+ spin_lock_init(&np->lock);
pci_set_drvdata(pdev, dev);
np->pci_dev = pdev;
+
+ np->mii_if.dev = dev;
+ np->mii_if.mdio_read = mdio_read;
+ np->mii_if.mdio_write = mdio_write;
+ np->mii_if.phy_id_mask = 0x1f;
+ np->mii_if.reg_num_mask = 0x1f;
+
drv_flags = netdrv_tbl[chip_idx].drv_flags;
option = card_idx < MAX_UNITS ? options[card_idx] : 0;
@@ -734,17 +919,41 @@
/* The lower four bits are the media type. */
if (option & 0x200)
- np->full_duplex = 1;
+ np->mii_if.full_duplex = 1;
if (card_idx < MAX_UNITS && full_duplex[card_idx] > 0)
- np->full_duplex = 1;
+ np->mii_if.full_duplex = 1;
- if (np->full_duplex)
- np->autoneg = 0;
+ if (np->mii_if.full_duplex)
+ np->mii_if.force_media = 1;
else
- np->autoneg = 1;
+ np->mii_if.force_media = 0;
np->speed100 = 1;
+ /* timer resolution is 128 * 0.8us */
+ np->intr_timer_ctrl = (((intr_latency * 10) / 1024) & IntrLatencyMask) |
+ Timer10X | EnableIntrMasking;
+
+ if (small_frames > 0) {
+ np->intr_timer_ctrl |= SmallFrameBypass;
+ switch (small_frames) {
+ case 1 ... 64:
+ np->intr_timer_ctrl |= SmallFrame64;
+ break;
+ case 65 ... 128:
+ np->intr_timer_ctrl |= SmallFrame128;
+ break;
+ case 129 ... 256:
+ np->intr_timer_ctrl |= SmallFrame256;
+ break;
+ default:
+ np->intr_timer_ctrl |= SmallFrame512;
+ if (small_frames > 512)
+ printk("Adjusting small_frames down to 512\n");
+ break;
+ }
+ }
+
/* The chip-specific entries in the device structure. */
dev->open = &netdev_open;
dev->hard_start_xmit = &start_tx;
@@ -757,11 +966,10 @@
if (mtu)
dev->mtu = mtu;
- i = register_netdev(dev);
- if (i)
+ if (register_netdev(dev))
goto err_out_cleardev;
- printk(KERN_INFO "%s: %s at 0x%lx, ",
+ printk(KERN_INFO "%s: %s at %#lx, ",
dev->name, netdrv_tbl[chip_idx].name, ioaddr);
for (i = 0; i < 5; i++)
printk("%2.2x:", dev->dev_addr[i]);
@@ -784,25 +992,23 @@
mii_status = mdio_read(dev, phy, MII_BMSR);
if (mii_status != 0) {
np->phys[phy_idx++] = phy;
- np->advertising = mdio_read(dev, phy, MII_ADVERTISE);
+ np->mii_if.advertising = mdio_read(dev, phy, MII_ADVERTISE);
printk(KERN_INFO "%s: MII PHY found at address %d, status "
- "0x%4.4x advertising %4.4x.\n",
- dev->name, phy, mii_status, np->advertising);
+ "%#4.4x advertising %#4.4x.\n",
+ dev->name, phy, mii_status, np->mii_if.advertising);
/* there can be only one PHY on-board */
break;
}
}
np->phy_cnt = phy_idx;
+ if (np->phy_cnt > 0)
+ np->mii_if.phy_id = np->phys[0];
+ else
+ memset(&np->mii_if, 0, sizeof(np->mii_if));
}
-#ifdef ZEROCOPY
- printk(KERN_INFO "%s: scatter-gather and hardware TCP cksumming enabled.\n",
- dev->name);
-#else /* not ZEROCOPY */
- printk(KERN_INFO "%s: scatter-gather and hardware TCP cksumming disabled.\n",
- dev->name);
-#endif /* not ZEROCOPY */
-
+ printk(KERN_INFO "%s: scatter-gather and hardware TCP cksumming %s.\n",
+ dev->name, enable_hw_cksum ? "enabled" : "disabled");
return 0;
err_out_cleardev:
@@ -811,7 +1017,6 @@
err_out_free_res:
pci_release_regions (pdev);
err_out_free_netdev:
- unregister_netdev(dev);
kfree(dev);
return -ENODEV;
}
@@ -839,7 +1044,6 @@
long mdio_addr = dev->base_addr + MIICtrl + (phy_id<<7) + (location<<2);
writel(value, mdio_addr);
/* The busy-wait will occur before a read. */
- return;
}
@@ -848,6 +1052,7 @@
struct netdev_private *np = dev->priv;
long ioaddr = dev->base_addr;
int i, retval;
+ size_t tx_done_q_size, rx_done_q_size, tx_ring_size, rx_ring_size;
/* Do we ever need to reset the chip??? */
@@ -865,61 +1070,61 @@
if (debug > 1)
printk(KERN_DEBUG "%s: netdev_open() irq %d.\n",
dev->name, dev->irq);
- /* Allocate the various queues, failing gracefully. */
- if (np->tx_done_q == 0)
- np->tx_done_q = pci_alloc_consistent(np->pci_dev, PAGE_SIZE, &np->tx_done_q_dma);
- if (np->rx_done_q == 0)
- np->rx_done_q = pci_alloc_consistent(np->pci_dev, sizeof(struct rx_done_desc) * DONE_Q_SIZE, &np->rx_done_q_dma);
- if (np->tx_ring == 0)
- np->tx_ring = pci_alloc_consistent(np->pci_dev, PAGE_SIZE, &np->tx_ring_dma);
- if (np->rx_ring == 0)
- np->rx_ring = pci_alloc_consistent(np->pci_dev, PAGE_SIZE, &np->rx_ring_dma);
- if (np->tx_done_q == 0 || np->rx_done_q == 0
- || np->rx_ring == 0 || np->tx_ring == 0) {
- if (np->tx_done_q)
- pci_free_consistent(np->pci_dev, PAGE_SIZE,
- np->tx_done_q, np->tx_done_q_dma);
- if (np->rx_done_q)
- pci_free_consistent(np->pci_dev, sizeof(struct rx_done_desc) * DONE_Q_SIZE,
- np->rx_done_q, np->rx_done_q_dma);
- if (np->tx_ring)
- pci_free_consistent(np->pci_dev, PAGE_SIZE,
- np->tx_ring, np->tx_ring_dma);
- if (np->rx_ring)
- pci_free_consistent(np->pci_dev, PAGE_SIZE,
- np->rx_ring, np->rx_ring_dma);
- COMPAT_MOD_DEC_USE_COUNT;
- return -ENOMEM;
+
+ /* Allocate the various queues. */
+ if (np->queue_mem == 0) {
+ tx_done_q_size = ((sizeof(struct tx_done_desc) * DONE_Q_SIZE + QUEUE_ALIGN - 1) / QUEUE_ALIGN) * QUEUE_ALIGN;
+ rx_done_q_size = ((sizeof(rx_done_desc) * DONE_Q_SIZE + QUEUE_ALIGN - 1) / QUEUE_ALIGN) * QUEUE_ALIGN;
+ tx_ring_size = ((sizeof(starfire_tx_desc) * TX_RING_SIZE + QUEUE_ALIGN - 1) / QUEUE_ALIGN) * QUEUE_ALIGN;
+ rx_ring_size = sizeof(struct starfire_rx_desc) * RX_RING_SIZE;
+ np->queue_mem_size = tx_done_q_size + rx_done_q_size + tx_ring_size + rx_ring_size;
+ np->queue_mem = pci_alloc_consistent(np->pci_dev, np->queue_mem_size, &np->queue_mem_dma);
+ if (np->queue_mem == 0) {
+ COMPAT_MOD_DEC_USE_COUNT;
+ return -ENOMEM;
+ }
+
+ np->tx_done_q = np->queue_mem;
+ np->tx_done_q_dma = np->queue_mem_dma;
+ np->rx_done_q = (void *) np->tx_done_q + tx_done_q_size;
+ np->rx_done_q_dma = np->tx_done_q_dma + tx_done_q_size;
+ np->tx_ring = (void *) np->rx_done_q + rx_done_q_size;
+ np->tx_ring_dma = np->rx_done_q_dma + rx_done_q_size;
+ np->rx_ring = (void *) np->tx_ring + tx_ring_size;
+ np->rx_ring_dma = np->tx_ring_dma + tx_ring_size;
}
+ /* Start with no carrier, it gets adjusted later */
+ netif_carrier_off(dev);
init_ring(dev);
/* Set the size of the Rx buffers. */
writel((np->rx_buf_sz << RxBufferLenShift) |
(0 << RxMinDescrThreshShift) |
RxPrefetchMode | RxVariableQ |
+ RX_Q_ENTRIES |
+ RX_DESC_Q_ADDR_SIZE | RX_DESC_ADDR_SIZE |
RxDescSpace4,
ioaddr + RxDescQCtrl);
-#ifdef ZEROCOPY
- /* Set Tx descriptor to type 0 and spacing to 64 bytes. */
- writel((2 << TxHiPriFIFOThreshShift) |
- (0 << TxPadLenShift) |
- (4 << TxDMABurstSizeShift) |
- TxDescSpace64 | TxDescType0,
- ioaddr + TxDescCtrl);
-#else /* not ZEROCOPY */
- /* Set Tx descriptor to type 1 and padding to 0 bytes. */
+ /* Set up the Rx DMA controller. */
+ writel(RxChecksumIgnore |
+ (0 << RxEarlyIntThreshShift) |
+ (6 << RxHighPrioThreshShift) |
+ ((DMA_BURST_SIZE / 32) << RxBurstSizeShift),
+ ioaddr + RxDMACtrl);
+
+ /* Set Tx descriptor */
writel((2 << TxHiPriFIFOThreshShift) |
(0 << TxPadLenShift) |
- (4 << TxDMABurstSizeShift) |
- TxDescSpaceUnlim | TxDescType1,
+ ((DMA_BURST_SIZE / 32) << TxDMABurstSizeShift) |
+ TX_DESC_Q_ADDR_SIZE |
+ TX_DESC_SPACING | TX_DESC_TYPE,
ioaddr + TxDescCtrl);
-#endif /* not ZEROCOPY */
-#if defined(ADDR_64BITS) && defined(__alpha__)
- /* XXX We really need a 64-bit PCI dma interfaces too... -DaveM */
- writel(np->rx_ring_dma >> 32, ioaddr + RxDescQHiAddr);
- writel(np->tx_ring_dma >> 32, ioaddr + TxRingHiAddr);
+#if defined(ADDR_64BITS)
+ writel(np->queue_mem_dma >> 32, ioaddr + RxDescQHiAddr);
+ writel(np->queue_mem_dma >> 32, ioaddr + TxRingHiAddr);
+ writel(np->queue_mem_dma >> 32, ioaddr + CompletionHiAddr);
#else
writel(0, ioaddr + RxDescQHiAddr);
writel(0, ioaddr + TxRingHiAddr);
@@ -929,32 +1134,23 @@
writel(np->tx_ring_dma, ioaddr + TxRingPtr);
writel(np->tx_done_q_dma, ioaddr + TxCompletionAddr);
-#ifdef full_rx_status
writel(np->rx_done_q_dma |
- RxComplType3 |
+ RxComplType |
(0 << RxComplThreshShift),
ioaddr + RxCompletionAddr);
-#else /* not full_rx_status */
-#ifdef csum_rx_status
- writel(np->rx_done_q_dma |
- RxComplType2 |
- (0 << RxComplThreshShift),
- ioaddr + RxCompletionAddr);
-#else /* not csum_rx_status */
- writel(np->rx_done_q_dma |
- RxComplType0 |
- (0 << RxComplThreshShift),
- ioaddr + RxCompletionAddr);
-#endif /* not csum_rx_status */
-#endif /* not full_rx_status */
if (debug > 1)
printk(KERN_DEBUG "%s: Filling in the station address.\n", dev->name);
- /* Fill both the unused Tx SA register and the Rx perfect filter. */
+ /* Fill both the Tx SA register and the Rx perfect filter. */
for (i = 0; i < 6; i++)
- writeb(dev->dev_addr[i], ioaddr + StationAddr + 5 - i);
- for (i = 0; i < 16; i++) {
+ writeb(dev->dev_addr[i], ioaddr + TxStationAddr + 5 - i);
+ /* The first entry is special because it bypasses the VLAN filter.
+ Don't use it. */
+ writew(0, ioaddr + PerfFilterTable);
+ writew(0, ioaddr + PerfFilterTable + 4);
+ writew(0, ioaddr + PerfFilterTable + 8);
+ for (i = 1; i < 16; i++) {
u16 *eaddrs = (u16 *)dev->dev_addr;
long setup_frm = ioaddr + PerfFilterTable + i * 16;
writew(cpu_to_be16(eaddrs[2]), setup_frm); setup_frm += 4;
@@ -964,16 +1160,14 @@
/* Initialize other registers. */
/* Configure the PCI bus bursts and FIFO thresholds. */
- np->tx_mode = 0x0C04; /* modified when link is up. */
- writel(0x8000 | np->tx_mode, ioaddr + TxMode);
+ np->tx_mode = TxFlowEnable|RxFlowEnable|PadEnable; /* modified when link is up. */
+ writel(MiiSoftReset | np->tx_mode, ioaddr + TxMode);
udelay(1000);
writel(np->tx_mode, ioaddr + TxMode);
np->tx_threshold = 4;
writel(np->tx_threshold, ioaddr + TxThreshold);
- interrupt_mitigation &= 0x1f;
- np->intr_mitigation = interrupt_mitigation;
- writel(np->intr_mitigation, ioaddr + IntrTimerCtrl);
+ writel(np->intr_timer_ctrl, ioaddr + IntrTimerCtrl);
netif_start_if(dev);
netif_start_queue(dev);
@@ -982,35 +1176,41 @@
printk(KERN_DEBUG "%s: Setting the Rx and Tx modes.\n", dev->name);
set_rx_mode(dev);
- np->advertising = mdio_read(dev, np->phys[0], MII_ADVERTISE);
+ np->mii_if.advertising = mdio_read(dev, np->phys[0], MII_ADVERTISE);
check_duplex(dev);
/* Enable GPIO interrupts on link change */
writel(0x0f00ff00, ioaddr + GPIOCtrl);
- /* Set the interrupt mask and enable PCI interrupts. */
+ /* Set the interrupt mask */
writel(IntrRxDone | IntrRxEmpty | IntrDMAErr |
- IntrTxDone | IntrStatsMax | IntrLinkChange |
- IntrNormalSummary | IntrAbnormalSummary |
+ IntrTxDMADone | IntrStatsMax | IntrLinkChange |
IntrRxGFPDead | IntrNoTxCsum | IntrTxBadID,
ioaddr + IntrEnable);
+ /* Enable PCI interrupts. */
writel(0x00800000 | readl(ioaddr + PCIDeviceConfig),
ioaddr + PCIDeviceConfig);
+#ifdef VLAN_SUPPORT
+ /* Set VLAN type to 802.1q */
+ writel(ETH_P_8021Q, ioaddr + VlanType);
+#endif /* VLAN_SUPPORT */
+
#ifdef HAS_FIRMWARE
/* Load Rx/Tx firmware into the frame processors */
for (i = 0; i < FIRMWARE_RX_SIZE * 2; i++)
writel(firmware_rx[i], ioaddr + RxGfpMem + i * 4);
for (i = 0; i < FIRMWARE_TX_SIZE * 2; i++)
writel(firmware_tx[i], ioaddr + TxGfpMem + i * 4);
- /* Enable the Rx and Tx units, and the Rx/Tx frame processors. */
- writel(0x003F, ioaddr + GenCtrl);
-#else /* not HAS_FIRMWARE */
- /* Enable the Rx and Tx units only. */
- writel(0x000F, ioaddr + GenCtrl);
-#endif /* not HAS_FIRMWARE */
+#endif /* HAS_FIRMWARE */
+ if (enable_hw_cksum)
+ /* Enable the Rx and Tx units, and the Rx/Tx frame processors. */
+ writel(TxEnable|TxGFPEnable|RxEnable|RxGFPEnable, ioaddr + GenCtrl);
+ else
+ /* Enable the Rx and Tx units only. */
+ writel(TxEnable|RxEnable, ioaddr + GenCtrl);
- if (debug > 2)
+ if (debug > 1)
printk(KERN_DEBUG "%s: Done netdev_open().\n",
dev->name);
@@ -1022,26 +1222,32 @@
{
struct netdev_private *np = dev->priv;
u16 reg0;
+ int silly_count = 1000;
- mdio_write(dev, np->phys[0], MII_ADVERTISE, np->advertising);
+ mdio_write(dev, np->phys[0], MII_ADVERTISE, np->mii_if.advertising);
mdio_write(dev, np->phys[0], MII_BMCR, BMCR_RESET);
udelay(500);
- while (mdio_read(dev, np->phys[0], MII_BMCR) & BMCR_RESET);
+ while (--silly_count && mdio_read(dev, np->phys[0], MII_BMCR) & BMCR_RESET)
+ /* do nothing */;
+ if (!silly_count) {
+ printk("%s: MII reset failed!\n", dev->name);
+ return;
+ }
reg0 = mdio_read(dev, np->phys[0], MII_BMCR);
- if (np->autoneg) {
+ if (!np->mii_if.force_media) {
reg0 |= BMCR_ANENABLE | BMCR_ANRESTART;
} else {
reg0 &= ~(BMCR_ANENABLE | BMCR_ANRESTART);
if (np->speed100)
reg0 |= BMCR_SPEED100;
- if (np->full_duplex)
+ if (np->mii_if.full_duplex)
reg0 |= BMCR_FULLDPLX;
printk(KERN_DEBUG "%s: Link forced to %sMbit %s-duplex\n",
dev->name,
np->speed100 ? "100" : "10",
- np->full_duplex ? "full" : "half");
+ np->mii_if.full_duplex ? "full" : "half");
}
mdio_write(dev, np->phys[0], MII_BMCR, reg0);
}
@@ -1051,25 +1257,22 @@
{
struct netdev_private *np = dev->priv;
long ioaddr = dev->base_addr;
+ int old_debug;
- printk(KERN_WARNING "%s: Transmit timed out, status %8.8x,"
- " resetting...\n", dev->name, (int)readl(ioaddr + IntrStatus));
-
-#ifndef __alpha__
- {
- int i;
- printk(KERN_DEBUG " Rx ring %p: ", np->rx_ring);
- for (i = 0; i < RX_RING_SIZE; i++)
- printk(" %8.8x", (unsigned int)le32_to_cpu(np->rx_ring[i].rxaddr));
- printk("\n"KERN_DEBUG" Tx ring %p: ", np->tx_ring);
- for (i = 0; i < TX_RING_SIZE; i++)
- printk(" %4.4x", le32_to_cpu(np->tx_ring[i].status));
- printk("\n");
- }
-#endif
+ printk(KERN_WARNING "%s: Transmit timed out, status %#8.8x, "
+ "resetting...\n", dev->name, (int) readl(ioaddr + IntrStatus));
/* Perhaps we should reinitialize the hardware here. */
- /* Stop and restart the chip's Tx processes . */
+
+ /*
+ * Stop and restart the interface.
+ * Cheat and increase the debug level temporarily.
+ */
+ old_debug = debug;
+ debug = 2;
+ netdev_close(dev);
+ netdev_open(dev);
+ debug = old_debug;
/* Trigger an immediate transmit demand. */
@@ -1085,9 +1288,8 @@
struct netdev_private *np = dev->priv;
int i;
- np->tx_full = 0;
- np->cur_rx = np->cur_tx = 0;
- np->dirty_rx = np->rx_done = np->dirty_tx = np->tx_done = 0;
+ np->cur_rx = np->cur_tx = np->reap_tx = 0;
+ np->dirty_rx = np->dirty_tx = np->rx_done = np->tx_done = 0;
np->rx_buf_sz = (dev->mtu <= 1500 ? PKT_BUF_SZ : dev->mtu + 32);
@@ -1100,7 +1302,7 @@
np->rx_info[i].mapping = pci_map_single(np->pci_dev, skb->tail, np->rx_buf_sz, PCI_DMA_FROMDEVICE);
skb->dev = dev; /* Mark as being used by this device. */
/* Grrr, we cannot offset to correctly align the IP header. */
- np->rx_ring[i].rxaddr = cpu_to_le32(np->rx_info[i].mapping | RxDescValid);
+ np->rx_ring[i].rxaddr = cpu_to_dma(np->rx_info[i].mapping | RxDescValid);
}
writew(i - 1, dev->base_addr + RxDescQIdx);
np->dirty_rx = (unsigned int)(i - RX_RING_SIZE);
@@ -1112,7 +1314,7 @@
np->rx_info[i].mapping = 0;
}
/* Mark the last entry as wrapping the ring. */
- np->rx_ring[i-1].rxaddr |= cpu_to_le32(RxDescEndRing);
+ np->rx_ring[RX_RING_SIZE - 1].rxaddr |= cpu_to_dma(RxDescEndRing);
/* Clear the completion rings. */
for (i = 0; i < DONE_Q_SIZE; i++) {
@@ -1120,18 +1322,9 @@
np->tx_done_q[i].status = 0;
}
- for (i = 0; i < TX_RING_SIZE; i++) {
- np->tx_info[i].skb = NULL;
- np->tx_info[i].first_mapping = 0;
-#ifdef ZEROCOPY
- {
- int j;
- for (j = 0; j < MAX_STARFIRE_FRAGS; j++)
- np->tx_info[i].frag_mapping[j] = 0;
- }
-#endif /* ZEROCOPY */
- np->tx_ring[i].status = 0;
- }
+ for (i = 0; i < TX_RING_SIZE; i++)
+ memset(&np->tx_info[i], 0, sizeof(np->tx_info[i]));
+
return;
}
@@ -1140,19 +1333,21 @@
{
struct netdev_private *np = dev->priv;
unsigned int entry;
-#ifdef ZEROCOPY
+ u32 status;
int i;
-#endif
kick_tx_timer(dev, tx_timeout, TX_TIMEOUT);
- /* Caution: the write order is important here, set the field
- with the "ownership" bits last. */
-
- /* Calculate the next Tx descriptor entry. */
- entry = np->cur_tx % TX_RING_SIZE;
+ /*
+ * be cautious here, wrapping the queue has weird semantics
+ * and we may not have enough slots even when it seems we do.
+ */
+ if ((np->cur_tx - np->dirty_tx) + skb_num_frags(skb) * 2 > TX_RING_SIZE) {
+ netif_stop_queue(dev);
+ return 1;
+ }
-#if defined(ZEROCOPY) && defined(HAS_FIRMWARE) && defined(HAS_BROKEN_FIRMWARE)
+#if defined(ZEROCOPY) && defined(HAS_BROKEN_FIRMWARE)
{
int has_bad_length = 0;
@@ -1169,85 +1364,72 @@
if (has_bad_length)
skb_checksum_help(skb);
}
-#endif /* ZEROCOPY && HAS_FIRMWARE && HAS_BROKEN_FIRMWARE */
-
- np->tx_info[entry].skb = skb;
- np->tx_info[entry].first_mapping =
- pci_map_single(np->pci_dev, skb->data, skb_first_frag_len(skb), PCI_DMA_TODEVICE);
-
- np->tx_ring[entry].first_addr = cpu_to_le32(np->tx_info[entry].first_mapping);
-#ifdef ZEROCOPY
- np->tx_ring[entry].first_len = cpu_to_le16(skb_first_frag_len(skb));
- np->tx_ring[entry].total_len = cpu_to_le16(skb->len);
- /* Add "| TxDescIntr" to generate Tx-done interrupts. */
- np->tx_ring[entry].status = cpu_to_le32(TxDescID | TxCRCEn);
- np->tx_ring[entry].nbufs = cpu_to_le32(skb_shinfo(skb)->nr_frags + 1);
-#else /* not ZEROCOPY */
- /* Add "| TxDescIntr" to generate Tx-done interrupts. */
- np->tx_ring[entry].status = cpu_to_le32(skb->len | TxDescID | TxCRCEn | 1 << 16);
-#endif /* not ZEROCOPY */
-
- if (entry >= TX_RING_SIZE-1) /* Wrap ring */
- np->tx_ring[entry].status |= cpu_to_le32(TxRingWrap | TxDescIntr);
-
-#ifdef ZEROCOPY
- if (skb->ip_summed == CHECKSUM_HW) {
- np->tx_ring[entry].status |= cpu_to_le32(TxCalTCP);
- np->stats.tx_compressed++;
- }
-#endif /* ZEROCOPY */
+#endif /* ZEROCOPY && HAS_BROKEN_FIRMWARE */
- if (debug > 5) {
-#ifdef ZEROCOPY
- printk(KERN_DEBUG "%s: Tx #%d slot %d status %8.8x nbufs %d len %4.4x/%4.4x.\n",
- dev->name, np->cur_tx, entry,
- le32_to_cpu(np->tx_ring[entry].status),
- le32_to_cpu(np->tx_ring[entry].nbufs),
- le32_to_cpu(np->tx_ring[entry].first_len),
- le32_to_cpu(np->tx_ring[entry].total_len));
-#else /* not ZEROCOPY */
- printk(KERN_DEBUG "%s: Tx #%d slot %d status %8.8x.\n",
- dev->name, np->cur_tx, entry,
- le32_to_cpu(np->tx_ring[entry].status));
-#endif /* not ZEROCOPY */
- }
-
-#ifdef ZEROCOPY
- for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
- skb_frag_t *this_frag = &skb_shinfo(skb)->frags[i];
+ entry = np->cur_tx % TX_RING_SIZE;
+ for (i = 0; i < skb_num_frags(skb); i++) {
+ int wrap_ring = 0;
+ status = TxDescID;
+
+ if (i == 0) {
+ np->tx_info[entry].skb = skb;
+ status |= TxCRCEn;
+ if (entry >= TX_RING_SIZE - skb_num_frags(skb)) {
+ status |= TxRingWrap;
+ wrap_ring = 1;
+ }
+ if (np->reap_tx) {
+ status |= TxDescIntr;
+ np->reap_tx = 0;
+ }
+ if (skb->ip_summed == CHECKSUM_HW) {
+ status |= TxCalTCP;
+ np->stats.tx_compressed++;
+ }
+ status |= skb_first_frag_len(skb) | (skb_num_frags(skb) << 16);
- /* we already have the proper value in entry */
- np->tx_info[entry].frag_mapping[i] =
- pci_map_single(np->pci_dev, page_address(this_frag->page) + this_frag->page_offset, this_frag->size, PCI_DMA_TODEVICE);
-
- np->tx_ring[entry].frag[i].addr = cpu_to_le32(np->tx_info[entry].frag_mapping[i]);
- np->tx_ring[entry].frag[i].len = cpu_to_le32(this_frag->size);
- if (debug > 5) {
- printk(KERN_DEBUG "%s: Tx #%d frag %d len %4.4x.\n",
- dev->name, np->cur_tx, i,
- le32_to_cpu(np->tx_ring[entry].frag[i].len));
- }
+ np->tx_info[entry].mapping =
+ pci_map_single(np->pci_dev, skb->data, skb_first_frag_len(skb), PCI_DMA_TODEVICE);
+ } else {
+#ifdef MAX_SKB_FRAGS
+ skb_frag_t *this_frag = &skb_shinfo(skb)->frags[i - 1];
+ status |= this_frag->size;
+ np->tx_info[entry].mapping =
+ pci_map_single(np->pci_dev, page_address(this_frag->page) + this_frag->page_offset, this_frag->size, PCI_DMA_TODEVICE);
+#endif /* MAX_SKB_FRAGS */
+ }
+
+ np->tx_ring[entry].addr = cpu_to_dma(np->tx_info[entry].mapping);
+ np->tx_ring[entry].status = cpu_to_le32(status);
+ if (debug > 3)
+ printk(KERN_DEBUG "%s: Tx #%d/#%d slot %d status %#8.8x.\n",
+ dev->name, np->cur_tx, np->dirty_tx,
+ entry, status);
+ if (wrap_ring) {
+ np->tx_info[entry].used_slots = TX_RING_SIZE - entry;
+ np->cur_tx += np->tx_info[entry].used_slots;
+ entry = 0;
+ } else {
+ np->tx_info[entry].used_slots = 1;
+ np->cur_tx += np->tx_info[entry].used_slots;
+ entry++;
+ }
+ /* scavenge the tx descriptors twice per TX_RING_SIZE */
+ if (np->cur_tx % (TX_RING_SIZE / 2) == 0)
+ np->reap_tx = 1;
}
-#endif /* ZEROCOPY */
-
- np->cur_tx++;
-
- if (entry >= TX_RING_SIZE-1) /* Wrap ring */
- entry = -1;
- entry++;
/* Non-x86: explicitly flush descriptor cache lines here. */
- /* Ensure everything is written back above before the transmit is
+ /* Ensure all descriptors are written back before the transmit is
initiated. - Jes */
wmb();
/* Update the producer index. */
- writel(entry * (sizeof(struct starfire_tx_desc) / 8), dev->base_addr + TxProducerIdx);
+ writel(entry * (sizeof(starfire_tx_desc) / 8), dev->base_addr + TxProducerIdx);
- if (np->cur_tx - np->dirty_tx >= TX_RING_SIZE - 1) {
- np->tx_full = 1;
+ /* 4 is arbitrary, but should be ok */
+ if ((np->cur_tx - np->dirty_tx) + 4 > TX_RING_SIZE)
netif_stop_queue(dev);
- }
dev->trans_start = jiffies;
@@ -1259,20 +1441,13 @@
after the Tx thread. */
static void intr_handler(int irq, void *dev_instance, struct pt_regs *rgs)
{
- struct net_device *dev = (struct net_device *)dev_instance;
+ struct net_device *dev = dev_instance;
struct netdev_private *np;
long ioaddr;
int boguscnt = max_interrupt_work;
int consumer;
int tx_status;
-#ifndef final_version /* Can never occur. */
- if (dev == NULL) {
- printk (KERN_ERR "Netdev interrupt handler(): IRQ %d for unknown device.\n", irq);
- return;
- }
-#endif
-
ioaddr = dev->base_addr;
np = dev->priv;
@@ -1280,83 +1455,69 @@
u32 intr_status = readl(ioaddr + IntrClear);
if (debug > 4)
- printk(KERN_DEBUG "%s: Interrupt status %4.4x.\n",
+ printk(KERN_DEBUG "%s: Interrupt status %#8.8x.\n",
dev->name, intr_status);
- if (intr_status == 0)
+ if (intr_status == 0 || intr_status == (u32) -1)
break;
- if (intr_status & IntrRxDone)
+ if (intr_status & (IntrRxDone | IntrRxEmpty))
netdev_rx(dev);
/* Scavenge the skbuff list based on the Tx-done queue.
There are redundant checks here that may be cleaned up
after the driver has proven to be reliable. */
consumer = readl(ioaddr + TxConsumerIdx);
- if (debug > 4)
+ if (debug > 3)
printk(KERN_DEBUG "%s: Tx Consumer index is %d.\n",
dev->name, consumer);
-#if 0
- if (np->tx_done >= 250 || np->tx_done == 0)
- printk(KERN_DEBUG "%s: Tx completion entry %d is %8.8x, %d is %8.8x.\n",
- dev->name, np->tx_done,
- le32_to_cpu(np->tx_done_q[np->tx_done].status),
- (np->tx_done+1) & (DONE_Q_SIZE-1),
- le32_to_cpu(np->tx_done_q[(np->tx_done+1)&(DONE_Q_SIZE-1)].status));
-#endif
while ((tx_status = le32_to_cpu(np->tx_done_q[np->tx_done].status)) != 0) {
- if (debug > 4)
- printk(KERN_DEBUG "%s: Tx completion entry %d is %8.8x.\n",
- dev->name, np->tx_done, tx_status);
+ if (debug > 3)
+ printk(KERN_DEBUG "%s: Tx completion #%d entry %d is %#8.8x.\n",
+ dev->name, np->dirty_tx, np->tx_done, tx_status);
if ((tx_status & 0xe0000000) == 0xa0000000) {
np->stats.tx_packets++;
} else if ((tx_status & 0xe0000000) == 0x80000000) {
- struct sk_buff *skb;
-#ifdef ZEROCOPY
- int i;
-#endif /* ZEROCOPY */
- u16 entry = tx_status; /* Implicit truncate */
- entry /= sizeof(struct starfire_tx_desc);
-
- skb = np->tx_info[entry].skb;
+ u16 entry = (tx_status & 0x7fff) / sizeof(starfire_tx_desc);
+ struct sk_buff *skb = np->tx_info[entry].skb;
np->tx_info[entry].skb = NULL;
pci_unmap_single(np->pci_dev,
- np->tx_info[entry].first_mapping,
+ np->tx_info[entry].mapping,
skb_first_frag_len(skb),
PCI_DMA_TODEVICE);
- np->tx_info[entry].first_mapping = 0;
-
-#ifdef ZEROCOPY
- for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
- pci_unmap_single(np->pci_dev,
- np->tx_info[entry].frag_mapping[i],
- skb_shinfo(skb)->frags[i].size,
- PCI_DMA_TODEVICE);
- np->tx_info[entry].frag_mapping[i] = 0;
+ np->tx_info[entry].mapping = 0;
+ np->dirty_tx += np->tx_info[entry].used_slots;
+ entry = (entry + np->tx_info[entry].used_slots) % TX_RING_SIZE;
+#ifdef MAX_SKB_FRAGS
+ {
+ int i;
+ for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) {
+ pci_unmap_single(np->pci_dev,
+ np->tx_info[entry].mapping,
+ skb_shinfo(skb)->frags[i].size,
+ PCI_DMA_TODEVICE);
+ np->dirty_tx++;
+ entry++;
+ }
}
-#endif /* ZEROCOPY */
-
- /* Scavenge the descriptor. */
+#endif /* MAX_SKB_FRAGS */
dev_kfree_skb_irq(skb);
-
- np->dirty_tx++;
}
np->tx_done_q[np->tx_done].status = 0;
- np->tx_done = (np->tx_done+1) & (DONE_Q_SIZE-1);
+ np->tx_done = (np->tx_done + 1) % DONE_Q_SIZE;
}
writew(np->tx_done, ioaddr + CompletionQConsumerIdx + 2);
- if (np->tx_full && np->cur_tx - np->dirty_tx < TX_RING_SIZE - 4) {
+ if (netif_queue_stopped(dev) &&
+ (np->cur_tx - np->dirty_tx + 4 < TX_RING_SIZE)) {
/* The ring is no longer full, wake the queue. */
- np->tx_full = 0;
netif_wake_queue(dev);
}
/* Stats overflow */
- if (intr_status & IntrStatsMax) {
+ if (intr_status & IntrStatsMax)
get_stats(dev);
- }
/* Media change interrupt. */
if (intr_status & IntrLinkChange)
@@ -1367,28 +1528,17 @@
netdev_error(dev, intr_status);
if (--boguscnt < 0) {
- printk(KERN_WARNING "%s: Too much work at interrupt, "
- "status=0x%4.4x.\n",
- dev->name, intr_status);
+ if (debug > 1)
+ printk(KERN_WARNING "%s: Too much work at interrupt, "
+ "status=%#8.8x.\n",
+ dev->name, intr_status);
break;
}
} while (1);
if (debug > 4)
- printk(KERN_DEBUG "%s: exiting interrupt, status=%#4.4x.\n",
- dev->name, (int)readl(ioaddr + IntrStatus));
-
-#ifndef final_version
- /* Code that should never be run! Remove after testing.. */
- {
- static int stopit = 10;
- if (!netif_running(dev) && --stopit < 0) {
- printk(KERN_ERR "%s: Emergency stop, looping startup interrupt.\n",
- dev->name);
- free_irq(irq, dev);
- }
- }
-#endif
+ printk(KERN_DEBUG "%s: exiting interrupt, status=%#8.8x.\n",
+ dev->name, (int) readl(ioaddr + IntrStatus));
}
@@ -1400,26 +1550,21 @@
int boguscnt = np->dirty_rx + RX_RING_SIZE - np->cur_rx;
u32 desc_status;
- if (np->rx_done_q == 0) {
- printk(KERN_ERR "%s: rx_done_q is NULL! rx_done is %d. %p.\n",
- dev->name, np->rx_done, np->tx_done_q);
- return 0;
- }
-
/* If EOP is set on the next entry, it's a new packet. Send it up. */
while ((desc_status = le32_to_cpu(np->rx_done_q[np->rx_done].status)) != 0) {
struct sk_buff *skb;
u16 pkt_len;
int entry;
+ rx_done_desc *desc = &np->rx_done_q[np->rx_done];
if (debug > 4)
- printk(KERN_DEBUG " netdev_rx() status of %d was %8.8x.\n", np->rx_done, desc_status);
+ printk(KERN_DEBUG " netdev_rx() status of %d was %#8.8x.\n", np->rx_done, desc_status);
if (--boguscnt < 0)
break;
- if ( ! (desc_status & RxOK)) {
+ if (!(desc_status & RxOK)) {
/* There was a error. */
if (debug > 2)
- printk(KERN_DEBUG " netdev_rx() Rx error was %8.8x.\n", desc_status);
+ printk(KERN_DEBUG " netdev_rx() Rx error was %#8.8x.\n", desc_status);
np->stats.rx_errors++;
if (desc_status & RxFIFOErr)
np->stats.rx_fifo_errors++;
@@ -1429,10 +1574,8 @@
pkt_len = desc_status; /* Implicitly Truncate */
entry = (desc_status >> 16) & 0x7ff;
-#ifndef final_version
if (debug > 4)
printk(KERN_DEBUG " netdev_rx() normal Rx pkt length %d, bogus_cnt %d.\n", pkt_len, boguscnt);
-#endif
/* Check if the packet is long enough to accept without copying
to a minimally-sized skbuff. */
if (pkt_len < rx_copybreak
@@ -1442,12 +1585,8 @@
pci_dma_sync_single(np->pci_dev,
np->rx_info[entry].mapping,
pkt_len, PCI_DMA_FROMDEVICE);
-#if HAS_IP_COPYSUM /* Call copy + cksum if available. */
eth_copy_and_sum(skb, np->rx_info[entry].skb->tail, pkt_len, 0);
skb_put(skb, pkt_len);
-#else
- memcpy(skb_put(skb, pkt_len), np->rx_info[entry].skb->tail, pkt_len);
-#endif
} else {
pci_unmap_single(np->pci_dev, np->rx_info[entry].mapping, np->rx_buf_sz, PCI_DMA_FROMDEVICE);
skb = np->rx_info[entry].skb;
@@ -1459,44 +1598,54 @@
/* You will want this info for the initial debug. */
if (debug > 5)
printk(KERN_DEBUG " Rx data %2.2x:%2.2x:%2.2x:%2.2x:%2.2x:"
- "%2.2x %2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2x %2.2x%2.2x "
- "%d.%d.%d.%d.\n",
+ "%2.2x %2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2x %2.2x%2.2x.\n",
skb->data[0], skb->data[1], skb->data[2], skb->data[3],
skb->data[4], skb->data[5], skb->data[6], skb->data[7],
skb->data[8], skb->data[9], skb->data[10],
- skb->data[11], skb->data[12], skb->data[13],
- skb->data[14], skb->data[15], skb->data[16],
- skb->data[17]);
+ skb->data[11], skb->data[12], skb->data[13]);
#endif
+
skb->protocol = eth_type_trans(skb, dev);
-#if defined(full_rx_status) || defined(csum_rx_status)
- if (le32_to_cpu(np->rx_done_q[np->rx_done].status2) & 0x01000000) {
+#if defined(HAS_FIRMWARE) || defined(VLAN_SUPPORT)
+ if (debug > 4)
+ printk(KERN_DEBUG " netdev_rx() status2 of %d was %#4.4x.\n", np->rx_done, le16_to_cpu(desc->status2));
+#endif
+#ifdef HAS_FIRMWARE
+ if (le16_to_cpu(desc->status2) & 0x0100) {
skb->ip_summed = CHECKSUM_UNNECESSARY;
np->stats.rx_compressed++;
}
/*
* This feature doesn't seem to be working, at least
* with the two firmware versions I have. If the GFP sees
- * a fragment, it either ignores it completely, or reports
+ * an IP fragment, it either ignores it completely, or reports
* "bad checksum" on it.
*
* Maybe I missed something -- corrections are welcome.
* Until then, the printk stays. :-) -Ion
*/
- else if (le32_to_cpu(np->rx_done_q[np->rx_done].status2) & 0x00400000) {
+ else if (le16_to_cpu(desc->status2) & 0x0040) {
skb->ip_summed = CHECKSUM_HW;
- skb->csum = le32_to_cpu(np->rx_done_q[np->rx_done].status2) & 0xffff;
- printk(KERN_DEBUG "%s: checksum_hw, status2 = %x\n", dev->name, np->rx_done_q[np->rx_done].status2);
+ skb->csum = le16_to_cpu(desc->csum);
+ printk(KERN_DEBUG "%s: checksum_hw, status2 = %#x\n", dev->name, le16_to_cpu(desc->status2));
}
-#endif
- netif_rx(skb);
+#endif /* HAS_FIRMWARE */
+#ifdef VLAN_SUPPORT
+ if (np->vlgrp && le16_to_cpu(desc->status2) & 0x0200) {
+ if (debug > 4)
+ printk(KERN_DEBUG " netdev_rx() vlanid = %d\n", le16_to_cpu(desc->vlanid));
+ /* vlan_hwaccel_rx expects a packet with the VLAN tag stripped out */
+ vlan_hwaccel_rx(skb, np->vlgrp, le16_to_cpu(desc->vlanid) & VLAN_VID_MASK);
+ } else
+#endif /* VLAN_SUPPORT */
+ netif_rx(skb);
dev->last_rx = jiffies;
np->stats.rx_packets++;
-next_rx:
+ next_rx:
np->cur_rx++;
- np->rx_done_q[np->rx_done].status = 0;
- np->rx_done = (np->rx_done + 1) & (DONE_Q_SIZE-1);
+ desc->status = 0;
+ np->rx_done = (np->rx_done + 1) % DONE_Q_SIZE;
}
writew(np->rx_done, dev->base_addr + CompletionQConsumerIdx);
@@ -1513,16 +1662,16 @@
pci_map_single(np->pci_dev, skb->tail, np->rx_buf_sz, PCI_DMA_FROMDEVICE);
skb->dev = dev; /* Mark as being used by this device. */
np->rx_ring[entry].rxaddr =
- cpu_to_le32(np->rx_info[entry].mapping | RxDescValid);
+ cpu_to_dma(np->rx_info[entry].mapping | RxDescValid);
}
if (entry == RX_RING_SIZE - 1)
- np->rx_ring[entry].rxaddr |= cpu_to_le32(RxDescEndRing);
+ np->rx_ring[entry].rxaddr |= cpu_to_dma(RxDescEndRing);
/* We could defer this until later... */
writew(entry, dev->base_addr + RxDescQIdx);
}
if (debug > 5)
- printk(KERN_DEBUG " exiting netdev_rx() status of %d was %8.8x.\n",
+ printk(KERN_DEBUG " exiting netdev_rx() status of %d was %#8.8x.\n",
np->rx_done, desc_status);
/* Restart Rx engine if stopped. */
@@ -1536,6 +1685,7 @@
long ioaddr = dev->base_addr;
u16 reg0, reg1, reg4, reg5;
u32 new_tx_mode;
+ u32 new_intr_timer_ctrl;
/* reset status first */
mdio_read(dev, np->phys[0], MII_BMCR);
@@ -1552,16 +1702,16 @@
reg5 = mdio_read(dev, np->phys[0], MII_LPA);
if (reg4 & ADVERTISE_100FULL && reg5 & LPA_100FULL) {
np->speed100 = 1;
- np->full_duplex = 1;
+ np->mii_if.full_duplex = 1;
} else if (reg4 & ADVERTISE_100HALF && reg5 & LPA_100HALF) {
np->speed100 = 1;
- np->full_duplex = 0;
+ np->mii_if.full_duplex = 0;
} else if (reg4 & ADVERTISE_10FULL && reg5 & LPA_10FULL) {
np->speed100 = 0;
- np->full_duplex = 1;
+ np->mii_if.full_duplex = 1;
} else {
np->speed100 = 0;
- np->full_duplex = 0;
+ np->mii_if.full_duplex = 0;
}
} else {
/* autonegotiation is disabled */
@@ -1570,25 +1720,35 @@
else
np->speed100 = 0;
if (reg0 & BMCR_FULLDPLX)
- np->full_duplex = 1;
+ np->mii_if.full_duplex = 1;
else
- np->full_duplex = 0;
+ np->mii_if.full_duplex = 0;
}
+ netif_carrier_on(dev);
printk(KERN_DEBUG "%s: Link is up, running at %sMbit %s-duplex\n",
dev->name,
np->speed100 ? "100" : "10",
- np->full_duplex ? "full" : "half");
+ np->mii_if.full_duplex ? "full" : "half");
- new_tx_mode = np->tx_mode & ~0x2; /* duplex setting */
- if (np->full_duplex)
- new_tx_mode |= 2;
+ new_tx_mode = np->tx_mode & ~FullDuplex; /* duplex setting */
+ if (np->mii_if.full_duplex)
+ new_tx_mode |= FullDuplex;
if (np->tx_mode != new_tx_mode) {
np->tx_mode = new_tx_mode;
- writel(np->tx_mode | 0x8000, ioaddr + TxMode);
+ writel(np->tx_mode | MiiSoftReset, ioaddr + TxMode);
udelay(1000);
writel(np->tx_mode, ioaddr + TxMode);
}
+
+ new_intr_timer_ctrl = np->intr_timer_ctrl & ~Timer10X;
+ if (np->speed100)
+ new_intr_timer_ctrl |= Timer10X;
+ if (np->intr_timer_ctrl != new_intr_timer_ctrl) {
+ np->intr_timer_ctrl = new_intr_timer_ctrl;
+ writel(new_intr_timer_ctrl, ioaddr + IntrTimerCtrl);
+ }
} else {
+ netif_carrier_off(dev);
printk(KERN_DEBUG "%s: Link is down\n", dev->name);
}
}
@@ -1600,9 +1760,12 @@
/* Came close to underrunning the Tx FIFO, increase threshold. */
if (intr_status & IntrTxDataLow) {
- writel(++np->tx_threshold, dev->base_addr + TxThreshold);
- printk(KERN_NOTICE "%s: Increasing Tx FIFO threshold to %d bytes\n",
- dev->name, np->tx_threshold * 16);
+ if (np->tx_threshold <= PKT_BUF_SZ / 16) {
+ writel(++np->tx_threshold, dev->base_addr + TxThreshold);
+ printk(KERN_NOTICE "%s: PCI bus congestion, increasing Tx FIFO threshold to %d bytes\n",
+ dev->name, np->tx_threshold * 16);
+ } else
+ printk(KERN_WARNING "%s: PCI Tx underflow -- adapter is probably malfunctioning\n", dev->name);
}
if (intr_status & IntrRxGFPDead) {
np->stats.rx_fifo_errors++;
@@ -1613,7 +1776,7 @@
np->stats.tx_errors++;
}
if ((intr_status & ~(IntrNormalMask | IntrAbnormalSummary | IntrLinkChange | IntrStatsMax | IntrTxDataLow | IntrRxGFPDead | IntrNoTxCsum | IntrPCIPad)) && debug)
- printk(KERN_ERR "%s: Something Wicked happened! %4.4x.\n",
+ printk(KERN_ERR "%s: Something Wicked happened! %#8.8x.\n",
dev->name, intr_status);
}
@@ -1648,39 +1811,67 @@
/* Chips may use the upper or lower CRC bits, and may reverse and/or invert
them. Select the endian-ness that results in minimal calculations.
*/
-
static void set_rx_mode(struct net_device *dev)
{
long ioaddr = dev->base_addr;
- u32 rx_mode;
+ u32 rx_mode = MinVLANPrio;
struct dev_mc_list *mclist;
int i;
+#ifdef VLAN_SUPPORT
+ struct netdev_private *np = dev->priv;
+
+ rx_mode |= VlanMode;
+ if (np->vlgrp) {
+ int vlan_count = 0;
+ long filter_addr = ioaddr + HashTable + 8;
+ for (i = 0; i < VLAN_VID_MASK; i++) {
+ if (np->vlgrp->vlan_devices[i]) {
+ if (vlan_count >= 32)
+ break;
+ writew(cpu_to_be16(i), filter_addr);
+ filter_addr += 16;
+ vlan_count++;
+ }
+ }
+ if (i == VLAN_VID_MASK) {
+ rx_mode |= PerfectFilterVlan;
+ while (vlan_count < 32) {
+ writew(0, filter_addr);
+ filter_addr += 16;
+ vlan_count++;
+ }
+ }
+ }
+#endif /* VLAN_SUPPORT */
if (dev->flags & IFF_PROMISC) { /* Set promiscuous. */
- rx_mode = AcceptBroadcast|AcceptAllMulticast|AcceptAll|AcceptMyPhys;
+ rx_mode |= AcceptAll;
} else if ((dev->mc_count > multicast_filter_limit)
|| (dev->flags & IFF_ALLMULTI)) {
/* Too many to match, or accept all multicasts. */
- rx_mode = AcceptBroadcast|AcceptAllMulticast|AcceptMyPhys;
- } else if (dev->mc_count <= 15) {
- /* Use the 16 element perfect filter, skip first entry. */
- long filter_addr = ioaddr + PerfFilterTable + 1 * 16;
- for (i = 1, mclist = dev->mc_list; mclist && i <= dev->mc_count;
+ rx_mode |= AcceptBroadcast|AcceptAllMulticast|PerfectFilter;
+ } else if (dev->mc_count <= 14) {
+ /* Use the 16 element perfect filter, skip first two entries. */
+ long filter_addr = ioaddr + PerfFilterTable + 2 * 16;
+ u16 *eaddrs;
+ for (i = 2, mclist = dev->mc_list; mclist && i < dev->mc_count + 2;
i++, mclist = mclist->next) {
- u16 *eaddrs = (u16 *)mclist->dmi_addr;
+ eaddrs = (u16 *)mclist->dmi_addr;
writew(cpu_to_be16(eaddrs[2]), filter_addr); filter_addr += 4;
writew(cpu_to_be16(eaddrs[1]), filter_addr); filter_addr += 4;
writew(cpu_to_be16(eaddrs[0]), filter_addr); filter_addr += 8;
}
+ eaddrs = (u16 *)dev->dev_addr;
while (i++ < 16) {
- writew(0xffff, filter_addr); filter_addr += 4;
- writew(0xffff, filter_addr); filter_addr += 4;
- writew(0xffff, filter_addr); filter_addr += 8;
+ writew(cpu_to_be16(eaddrs[0]), filter_addr); filter_addr += 4;
+ writew(cpu_to_be16(eaddrs[1]), filter_addr); filter_addr += 4;
+ writew(cpu_to_be16(eaddrs[2]), filter_addr); filter_addr += 8;
}
- rx_mode = AcceptBroadcast | AcceptMyPhys;
+ rx_mode |= AcceptBroadcast|PerfectFilter;
} else {
/* Must use a multicast hash table. */
long filter_addr;
+ u16 *eaddrs;
u16 mc_filter[32] __attribute__ ((aligned(sizeof(long)))); /* Multicast hash filter */
memset(mc_filter, 0, sizeof(mc_filter));
@@ -1691,16 +1882,17 @@
*fptr |= cpu_to_le32(1 << (bit_nr & 31));
}
- /* Clear the perfect filter list, skip first entry. */
- filter_addr = ioaddr + PerfFilterTable + 1 * 16;
- for (i = 1; i < 16; i++) {
- writew(0xffff, filter_addr); filter_addr += 4;
- writew(0xffff, filter_addr); filter_addr += 4;
- writew(0xffff, filter_addr); filter_addr += 8;
+ /* Clear the perfect filter list, skip first two entries. */
+ filter_addr = ioaddr + PerfFilterTable + 2 * 16;
+ eaddrs = (u16 *)dev->dev_addr;
+ for (i = 2; i < 16; i++) {
+ writew(cpu_to_be16(eaddrs[0]), filter_addr); filter_addr += 4;
+ writew(cpu_to_be16(eaddrs[1]), filter_addr); filter_addr += 4;
+ writew(cpu_to_be16(eaddrs[2]), filter_addr); filter_addr += 8;
}
- for (filter_addr = ioaddr + HashTable, i=0; i < 32; filter_addr+= 16, i++)
+ for (filter_addr = ioaddr + HashTable, i = 0; i < 32; filter_addr+= 16, i++)
writew(mc_filter[i], filter_addr);
- rx_mode = AcceptBroadcast | AcceptMulticast | AcceptMyPhys;
+ rx_mode |= AcceptBroadcast|PerfectFilter|HashFilter;
}
writel(rx_mode, ioaddr + RxFilterMode);
}
@@ -1715,77 +1907,6 @@
return -EFAULT;
switch (ecmd.cmd) {
- case ETHTOOL_GSET:
- ecmd.supported =
- SUPPORTED_10baseT_Half |
- SUPPORTED_10baseT_Full |
- SUPPORTED_100baseT_Half |
- SUPPORTED_100baseT_Full |
- SUPPORTED_Autoneg |
- SUPPORTED_MII;
-
- ecmd.advertising = ADVERTISED_MII;
- if (np->advertising & ADVERTISE_10HALF)
- ecmd.advertising |= ADVERTISED_10baseT_Half;
- if (np->advertising & ADVERTISE_10FULL)
- ecmd.advertising |= ADVERTISED_10baseT_Full;
- if (np->advertising & ADVERTISE_100HALF)
- ecmd.advertising |= ADVERTISED_100baseT_Half;
- if (np->advertising & ADVERTISE_100FULL)
- ecmd.advertising |= ADVERTISED_100baseT_Full;
- if (np->autoneg) {
- ecmd.advertising |= ADVERTISED_Autoneg;
- ecmd.autoneg = AUTONEG_ENABLE;
- } else
- ecmd.autoneg = AUTONEG_DISABLE;
-
- ecmd.port = PORT_MII;
- ecmd.transceiver = XCVR_INTERNAL;
- ecmd.phy_address = np->phys[0];
- ecmd.speed = np->speed100 ? SPEED_100 : SPEED_10;
- ecmd.duplex = np->full_duplex ? DUPLEX_FULL : DUPLEX_HALF;
- ecmd.maxtxpkt = TX_RING_SIZE;
- ecmd.maxrxpkt = np->intr_mitigation; /* not 100% accurate */
-
-
- if (copy_to_user(useraddr, &ecmd, sizeof(ecmd)))
- return -EFAULT;
- return 0;
-
- case ETHTOOL_SSET: {
- u16 autoneg, speed100, full_duplex;
-
- autoneg = (ecmd.autoneg == AUTONEG_ENABLE);
- speed100 = (ecmd.speed == SPEED_100);
- full_duplex = (ecmd.duplex == DUPLEX_FULL);
-
- np->autoneg = autoneg;
- if (speed100 != np->speed100 ||
- full_duplex != np->full_duplex) {
- np->speed100 = speed100;
- np->full_duplex = full_duplex;
- /* change advertising bits */
- np->advertising &= ~(ADVERTISE_10HALF |
- ADVERTISE_10FULL |
- ADVERTISE_100HALF |
- ADVERTISE_100FULL |
- ADVERTISE_100BASE4);
- if (speed100) {
- if (full_duplex)
- np->advertising |= ADVERTISE_100FULL;
- else
- np->advertising |= ADVERTISE_100HALF;
- } else {
- if (full_duplex)
- np->advertising |= ADVERTISE_10FULL;
- else
- np->advertising |= ADVERTISE_10HALF;
- }
- }
- check_duplex(dev);
- return 0;
- }
-
case ETHTOOL_GDRVINFO: {
struct ethtool_drvinfo info;
memset(&info, 0, sizeof(info));
@@ -1799,26 +1920,36 @@
return 0;
}
+ /* get settings */
+ case ETHTOOL_GSET: {
+ struct ethtool_cmd ecmd = { ETHTOOL_GSET };
+ spin_lock_irq(&np->lock);
+ mii_ethtool_gset(&np->mii_if, &ecmd);
+ spin_unlock_irq(&np->lock);
+ if (copy_to_user(useraddr, &ecmd, sizeof(ecmd)))
+ return -EFAULT;
+ return 0;
+ }
+ /* set settings */
+ case ETHTOOL_SSET: {
+ int r;
+ struct ethtool_cmd ecmd;
+ if (copy_from_user(&ecmd, useraddr, sizeof(ecmd)))
+ return -EFAULT;
+ spin_lock_irq(&np->lock);
+ r = mii_ethtool_sset(&np->mii_if, &ecmd);
+ spin_unlock_irq(&np->lock);
+ check_duplex(dev);
+ return r;
+ }
/* restart autonegotiation */
case ETHTOOL_NWAY_RST: {
- int tmp;
- int r = -EINVAL;
- /* if autoneg is off, it's an error */
- tmp = mdio_read(dev, np->phys[0], MII_BMCR);
- if (tmp & BMCR_ANENABLE) {
- tmp |= (BMCR_ANRESTART);
- mdio_write(dev, np->phys[0], MII_BMCR, tmp);
- r = 0;
- }
- return r;
+ return mii_nway_restart(&np->mii_if);
}
/* get link status */
case ETHTOOL_GLINK: {
struct ethtool_value edata = {ETHTOOL_GLINK};
- if (mdio_read(dev, np->phys[0], MII_BMSR) & BMSR_LSTATUS)
- edata.data = 1;
- else
- edata.data = 0;
+ edata.data = mii_link_ok(&np->mii_if);
if (copy_to_user(useraddr, &edata, sizeof(edata)))
return -EFAULT;
return 0;
@@ -1849,50 +1980,25 @@
static int netdev_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
{
struct netdev_private *np = dev->priv;
- struct mii_ioctl_data *data = (struct mii_ioctl_data *)&rq->ifr_data;
+ struct mii_ioctl_data *data = (struct mii_ioctl_data *) & rq->ifr_data;
+ int rc;
- switch(cmd) {
- case SIOCETHTOOL:
- return netdev_ethtool_ioctl(dev, (void *) rq->ifr_data);
-
- /* Legacy mii-diag interface */
- case SIOCGMIIPHY: /* Get address of MII PHY in use. */
- case SIOCDEVPRIVATE: /* for binary compat, remove in 2.5 */
- data->phy_id = np->phys[0] & 0x1f;
- /* Fall Through */
-
- case SIOCGMIIREG: /* Read MII PHY register. */
- case SIOCDEVPRIVATE+1: /* for binary compat, remove in 2.5 */
- data->val_out = mdio_read(dev, data->phy_id & 0x1f, data->reg_num & 0x1f);
- return 0;
+ if (!netif_running(dev))
+ return -EINVAL;
- case SIOCSMIIREG: /* Write MII PHY register. */
- case SIOCDEVPRIVATE+2: /* for binary compat, remove in 2.5 */
- if (!capable(CAP_NET_ADMIN))
- return -EPERM;
- if (data->phy_id == np->phys[0]) {
- u16 value = data->val_in;
- switch (data->reg_num) {
- case 0:
- if (value & (BMCR_RESET | BMCR_ANENABLE))
- /* Autonegotiation. */
- np->autoneg = 1;
- else {
- np->full_duplex = (value & BMCR_FULLDPLX) ? 1 : 0;
- np->autoneg = 0;
- }
- break;
- case 4:
- np->advertising = value;
- break;
- }
+ if (cmd == SIOCETHTOOL)
+ rc = netdev_ethtool_ioctl(dev, (void *) rq->ifr_data);
+
+ else {
+ spin_lock_irq(&np->lock);
+ rc = generic_mii_ioctl(&np->mii_if, data, cmd, NULL);
+ spin_unlock_irq(&np->lock);
+
+ if ((cmd == SIOCSMIIREG) && (data->phy_id == np->phys[0]))
check_duplex(dev);
- }
- mdio_write(dev, data->phy_id & 0x1f, data->reg_num & 0x1f, data->val_in);
- return 0;
- default:
- return -EOPNOTSUPP;
}
+
+ return rc;
}
static int netdev_close(struct net_device *dev)
@@ -1905,41 +2011,42 @@
netif_stop_if(dev);
if (debug > 1) {
- printk(KERN_DEBUG "%s: Shutting down ethercard, Intr status %4.4x.\n",
- dev->name, (int)readl(ioaddr + IntrStatus));
- printk(KERN_DEBUG "%s: Queue pointers were Tx %d / %d, Rx %d / %d.\n",
- dev->name, np->cur_tx, np->dirty_tx, np->cur_rx, np->dirty_rx);
+ printk(KERN_DEBUG "%s: Shutting down ethercard, Intr status %#8.8x.\n",
+ dev->name, (int) readl(ioaddr + IntrStatus));
+ printk(KERN_DEBUG "%s: Queue pointers were Tx %d / %d, Rx %d / %d.\n",
+ dev->name, np->cur_tx, np->dirty_tx,
+ np->cur_rx, np->dirty_rx);
}
/* Disable interrupts by clearing the interrupt mask. */
writel(0, ioaddr + IntrEnable);
/* Stop the chip's Tx and Rx processes. */
+ writel(0, ioaddr + GenCtrl);
+ readl(ioaddr + GenCtrl);
-#ifdef __i386__
- if (debug > 2) {
- printk("\n"KERN_DEBUG" Tx ring at %8.8x:\n",
- np->tx_ring_dma);
+ if (debug > 5) {
+ printk(KERN_DEBUG" Tx ring at %#llx:\n",
+ (long long) np->tx_ring_dma);
for (i = 0; i < 8 /* TX_RING_SIZE is huge! */; i++)
- printk(KERN_DEBUG " #%d desc. %8.8x %8.8x -> %8.8x.\n",
+ printk(KERN_DEBUG " #%d desc. %#8.8x %#llx -> %#8.8x.\n",
i, le32_to_cpu(np->tx_ring[i].status),
- le32_to_cpu(np->tx_ring[i].first_addr),
+ (long long) dma_to_cpu(np->tx_ring[i].addr),
le32_to_cpu(np->tx_done_q[i].status));
- printk(KERN_DEBUG " Rx ring at %8.8x -> %p:\n",
- np->rx_ring_dma, np->rx_done_q);
+ printk(KERN_DEBUG " Rx ring at %#llx -> %p:\n",
+ (long long) np->rx_ring_dma, np->rx_done_q);
if (np->rx_done_q)
for (i = 0; i < 8 /* RX_RING_SIZE */; i++) {
- printk(KERN_DEBUG " #%d desc. %8.8x -> %8.8x\n",
- i, le32_to_cpu(np->rx_ring[i].rxaddr), le32_to_cpu(np->rx_done_q[i].status));
+ printk(KERN_DEBUG " #%d desc. %#llx -> %#8.8x\n",
+ i, (long long) dma_to_cpu(np->rx_ring[i].rxaddr), le32_to_cpu(np->rx_done_q[i].status));
}
}
-#endif /* __i386__ debugging only */
free_irq(dev->irq, dev);
/* Free all the skbuffs in the Rx queue. */
for (i = 0; i < RX_RING_SIZE; i++) {
- np->rx_ring[i].rxaddr = cpu_to_le32(0xBADF00D0); /* An invalid address. */
+ np->rx_ring[i].rxaddr = cpu_to_dma(0xBADF00D0); /* An invalid address. */
if (np->rx_info[i].skb != NULL) {
pci_unmap_single(np->pci_dev, np->rx_info[i].mapping, np->rx_buf_sz, PCI_DMA_FROMDEVICE);
dev_kfree_skb(np->rx_info[i].skb);
@@ -1949,28 +2056,14 @@
}
for (i = 0; i < TX_RING_SIZE; i++) {
struct sk_buff *skb = np->tx_info[i].skb;
-#ifdef ZEROCOPY
- int j;
-#endif /* ZEROCOPY */
if (skb == NULL)
continue;
pci_unmap_single(np->pci_dev,
- np->tx_info[i].first_mapping,
+ np->tx_info[i].mapping,
skb_first_frag_len(skb), PCI_DMA_TODEVICE);
- np->tx_info[i].first_mapping = 0;
+ np->tx_info[i].mapping = 0;
dev_kfree_skb(skb);
np->tx_info[i].skb = NULL;
-#ifdef ZEROCOPY
- for (j = 0; j < MAX_STARFIRE_FRAGS; j++)
- if (np->tx_info[i].frag_mapping[j]) {
- pci_unmap_single(np->pci_dev,
- np->tx_info[i].frag_mapping[j],
- skb_shinfo(skb)->frags[j].size,
- PCI_DMA_TODEVICE);
- np->tx_info[i].frag_mapping[j] = 0;
- } else
- break;
-#endif /* ZEROCOPY */
}
COMPAT_MOD_DEC_USE_COUNT;
@@ -1988,19 +2081,8 @@
BUG();
np = dev->priv;
- if (np->tx_done_q)
- pci_free_consistent(pdev, PAGE_SIZE,
- np->tx_done_q, np->tx_done_q_dma);
- if (np->rx_done_q)
- pci_free_consistent(pdev,
- sizeof(struct rx_done_desc) * DONE_Q_SIZE,
- np->rx_done_q, np->rx_done_q_dma);
- if (np->tx_ring)
- pci_free_consistent(pdev, PAGE_SIZE,
- np->tx_ring, np->tx_ring_dma);
- if (np->rx_ring)
- pci_free_consistent(pdev, PAGE_SIZE,
- np->rx_ring, np->rx_ring_dma);
+ if (np->queue_mem)
+ pci_free_consistent(pdev, np->queue_mem_size, np->queue_mem, np->queue_mem_dma);
unregister_netdev(dev);
iounmap((char *)dev->base_addr);
@@ -2012,10 +2094,10 @@
static struct pci_driver starfire_driver = {
- name: DRV_NAME,
- probe: starfire_init_one,
- remove: __devexit_p(starfire_remove_one),
- id_table: starfire_pci_tbl,
+ .name = DRV_NAME,
+ .probe = starfire_init_one,
+ .remove = __devexit_p(starfire_remove_one),
+ .id_table = starfire_pci_tbl,
};
@@ -2025,6 +2107,17 @@
#ifdef MODULE
printk(version);
#endif
+#ifndef ADDR_64BITS
+ /* we can do this test only at run-time... sigh */
+ if (sizeof(dma_addr_t) == sizeof(u64)) {
+ printk("This driver has not been ported to this 64-bit architecture yet\n");
+ return -ENODEV;
+ }
+#endif /* not ADDR_64BITS */
+#ifndef HAS_FIRMWARE
+ /* unconditionally disable hw cksums if firmware is not present */
+ enable_hw_cksum = 0;
+#endif /* not HAS_FIRMWARE */
return pci_module_init (&starfire_driver);
}
@@ -2041,8 +2134,6 @@
/*
* Local variables:
- * compile-command: "gcc -DMODULE -Wall -Wstrict-prototypes -O2 -c starfire.c"
- * simple-compile-command: "gcc -DMODULE -O2 -c starfire.c"
* c-basic-offset: 8
* tab-width: 8
* End:
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)