patch-2.4.19 linux-2.4.19/arch/mips/ddb5xxx/ddb5476/setup.c

• Lines: 332
• Date: Fri Aug 2 17:39:43 2002
• Orig file: linux-2.4.18/arch/mips/ddb5xxx/ddb5476/setup.c
• Orig date: Wed Dec 31 16:00:00 1969

diff -urN linux-2.4.18/arch/mips/ddb5xxx/ddb5476/setup.c linux-2.4.19/arch/mips/ddb5xxx/ddb5476/setup.c
@@ -0,0 +1,331 @@
+/*
+ *  arch/mips/ddb5476/setup.c -- NEC DDB Vrc-5476 setup routines
+ *
+ *  Copyright (C) 2000 Geert Uytterhoeven <geert@sonycom.com>
+ *                     Sony Software Development Center Europe (SDCE), Brussels
+ */
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/kbd_ll.h>
+#include <linux/kernel.h>
+#include <linux/kdev_t.h>
+#include <linux/types.h>
+#include <linux/console.h>
+#include <linux/sched.h>
+#include <linux/mc146818rtc.h>
+#include <linux/pc_keyb.h>
+#include <linux/pci.h>
+#include <linux/ide.h>
+
+#include <asm/addrspace.h>
+#include <asm/bcache.h>
+#include <asm/keyboard.h>
+#include <asm/irq.h>
+#include <asm/reboot.h>
+#include <asm/gdb-stub.h>
+#include <asm/time.h>
+#include <asm/debug.h>
+
+#include <asm/ddb5xxx/ddb5xxx.h>
+
+// #define USE_CPU_COUNTER_TIMER	/* whether we use cpu counter */
+
+#ifdef USE_CPU_COUNTER_TIMER
+
+#define CPU_COUNTER_FREQUENCY           83000000
+#else
+/* otherwise we use general purpose timer */
+#define TIMER_FREQUENCY			83000000
+#define TIMER_BASE			DDB_T2CTRL
+#define TIMER_IRQ			(VRC5476_IRQ_BASE + VRC5476_IRQ_GPT)
+#endif
+
+#ifdef CONFIG_REMOTE_DEBUG
+extern void breakpoint(void);
+#endif
+
+extern struct ide_ops std_ide_ops;
+extern struct kbd_ops std_kbd_ops;
+
+static void (*back_to_prom) (void) = (void (*)(void)) 0xbfc00000;
+
+static void ddb_machine_restart(char *command)
+{
+	u32 t;
+
+	/* PCI cold reset */
+	t = ddb_in32(DDB_PCICTRL + 4);
+	t |= 0x40000000;
+	ddb_out32(DDB_PCICTRL + 4, t);
+	/* CPU cold reset */
+	t = ddb_in32(DDB_CPUSTAT);
+	t |= 1;
+	ddb_out32(DDB_CPUSTAT, t);
+	/* Call the PROM */
+	back_to_prom();
+}
+
+static void ddb_machine_halt(void)
+{
+	printk(KERN_NOTICE "DDB Vrc-5476 halted.\n");
+	while (1);
+}
+
+static void ddb_machine_power_off(void)
+{
+	printk(KERN_NOTICE "DDB Vrc-5476 halted. Please turn off the power.\n");
+	while (1);
+}
+
+extern void ddb_irq_setup(void);
+extern void rtc_ds1386_init(unsigned long base);
+
+static void __init ddb_time_init(void)
+{
+#if defined(USE_CPU_COUNTER_TIMER)
+	mips_counter_frequency = CPU_COUNTER_FREQUENCY;
+#endif
+
+	/* we have ds1396 RTC chip */
+	rtc_ds1386_init(KSEG1ADDR(DDB_PCI_MEM_BASE));
+}
+
+
+extern int setup_irq(unsigned int irq, struct irqaction *irqaction);
+static void __init ddb_timer_setup(struct irqaction *irq)
+{
+#if defined(USE_CPU_COUNTER_TIMER)
+
+	unsigned int count;
+
+	/* we are using the cpu counter for timer interrupts */
+	setup_irq(CPU_IRQ_BASE + 7, irq);
+
+	/* to generate the first timer interrupt */
+	count = read_32bit_cp0_register(CP0_COUNT);
+	write_32bit_cp0_register(CP0_COMPARE, count + 1000);
+
+#else
+
+	ddb_out32(TIMER_BASE, TIMER_FREQUENCY/HZ);
+	ddb_out32(TIMER_BASE+4, 0x1);	/* enable timer */
+	setup_irq(TIMER_IRQ, irq);
+#endif
+}
+
+static struct {
+	struct resource dma1;
+	struct resource pic1;
+	struct resource timer;
+	struct resource rtc;
+	struct resource dma_page_reg;
+	struct resource pic2;
+	struct resource dma2;
+} ddb5476_ioport = {
+	{
+	"dma1", 0x00, 0x1f, IORESOURCE_BUSY}, {
+	"pic1", 0x20, 0x3f, IORESOURCE_BUSY}, {
+	"timer", 0x40, 0x5f, IORESOURCE_BUSY}, {
+	"rtc", 0x70, 0x7f, IORESOURCE_BUSY}, {
+	"dma page reg", 0x80, 0x8f, IORESOURCE_BUSY}, {
+	"pic2", 0xa0, 0xbf, IORESOURCE_BUSY}, {
+	"dma2", 0xc0, 0xdf, IORESOURCE_BUSY}
+};
+
+static struct {
+	struct resource nile4;
+} ddb5476_iomem = {
+	{ "Nile 4", DDB_BASE, DDB_BASE + DDB_SIZE - 1, IORESOURCE_BUSY}
+};
+
+static void ddb5476_board_init(void);
+extern void ddb5476_irq_setup(void);
+extern void (*irq_setup)(void);
+
+void __init 
+ddb_setup(void)
+{
+	extern int panic_timeout;
+
+	irq_setup = ddb5476_irq_setup;
+	set_io_port_base(KSEG1ADDR(DDB_PCI_IO_BASE));
+
+	board_time_init = ddb_time_init;
+	board_timer_setup = ddb_timer_setup;
+
+	_machine_restart = ddb_machine_restart;
+	_machine_halt = ddb_machine_halt;
+	_machine_power_off = ddb_machine_power_off;
+
+	/* request io port/mem resources  */
+	if (request_resource(&ioport_resource, &ddb5476_ioport.dma1) ||
+	    request_resource(&ioport_resource, &ddb5476_ioport.pic1) ||
+	    request_resource(&ioport_resource, &ddb5476_ioport.timer) ||
+	    request_resource(&ioport_resource, &ddb5476_ioport.rtc) ||
+	    request_resource(&ioport_resource,
+			     &ddb5476_ioport.dma_page_reg)
+	    || request_resource(&ioport_resource, &ddb5476_ioport.pic2)
+	    || request_resource(&ioport_resource, &ddb5476_ioport.dma2)
+	    || request_resource(&iomem_resource, &ddb5476_iomem.nile4)) {
+		printk
+		    ("ddb_setup - requesting oo port resources failed.\n");
+		for (;;);
+	}
+#ifdef CONFIG_BLK_DEV_IDE
+	ide_ops = &std_ide_ops;
+#endif
+
+#ifdef CONFIG_PC_KEYB
+	kbd_ops = &std_kbd_ops;
+#endif
+
+	/* Reboot on panic */
+	panic_timeout = 180;
+
+	/* [jsun] we need to set BAR0 so that SDRAM 0 appears at 0x0 in PCI */
+	/* *(long*)0xbfa00218 = 0x8; */
+
+#ifdef CONFIG_FB
+	conswitchp = &dummy_con;
+#endif
+
+	/* board initialization stuff */
+	ddb5476_board_init();
+}
+
+/*
+ * We don't trust bios.  We essentially does hardware re-initialization
+ * as complete as possible, as far as we know we can safely do.
+ */
+static void 
+ddb5476_board_init(void)
+{
+	/* ----------- setup PDARs ------------ */
+	/* check SDRAM0, whether we are on MEM bus does not matter */
+	db_assert((ddb_in32(DDB_SDRAM0) & 0xffffffef) ==
+		  ddb_calc_pdar(DDB_SDRAM_BASE, DDB_SDRAM_SIZE, 32, 0, 1));
+
+	/* SDRAM1 should be turned off.  What is this for anyway ? */
+	db_assert( (ddb_in32(DDB_SDRAM1) & 0xf) == 0);
+
+	/* flash 1&2, DDB status, DDB control */
+	ddb_set_pdar(DDB_DCS2, DDB_DCS2_BASE, DDB_DCS2_SIZE, 16, 0, 0);
+	ddb_set_pdar(DDB_DCS3, DDB_DCS3_BASE, DDB_DCS3_SIZE, 16, 0, 0);
+	ddb_set_pdar(DDB_DCS4, DDB_DCS4_BASE, DDB_DCS4_SIZE, 8, 0, 0);
+	ddb_set_pdar(DDB_DCS5, DDB_DCS5_BASE, DDB_DCS5_SIZE, 8, 0, 0);
+
+	/* shut off other pdar so they don't accidentally get into the way */
+	ddb_set_pdar(DDB_DCS6, 0xffffffff, 0, 32, 0, 0);
+	ddb_set_pdar(DDB_DCS7, 0xffffffff, 0, 32, 0, 0);
+	ddb_set_pdar(DDB_DCS8, 0xffffffff, 0, 32, 0, 0);
+
+	/* verify VRC5477 base addr */
+	/* don't care about some details */
+	db_assert((ddb_in32(DDB_INTCS) & 0xffffff0f) ==
+		  ddb_calc_pdar(DDB_INTCS_BASE, DDB_INTCS_SIZE, 8, 0, 0));
+
+	/* verify BOOT ROM addr */
+	/* don't care about some details */
+	db_assert((ddb_in32(DDB_BOOTCS) & 0xffffff0f) ==
+		  ddb_calc_pdar(DDB_BOOTCS_BASE, DDB_BOOTCS_SIZE, 8, 0, 0));
+
+	/* setup PCI windows - window1 for MEM/config, window0 for IO */
+	ddb_set_pdar(DDB_PCIW0, DDB_PCI_IO_BASE, DDB_PCI_IO_SIZE, 32, 0, 1);
+	ddb_set_pmr(DDB_PCIINIT0, DDB_PCICMD_IO, 0, DDB_PCI_ACCESS_32);
+
+	ddb_set_pdar(DDB_PCIW1, DDB_PCI_MEM_BASE, DDB_PCI_MEM_SIZE, 32, 0, 1);
+	ddb_set_pmr(DDB_PCIINIT1, DDB_PCICMD_MEM, DDB_PCI_MEM_BASE, DDB_PCI_ACCESS_32);
+
+	/* ----------- setup PDARs ------------ */
+	/* this is problematic - it will reset Aladin which cause we loose
+	 * serial port, and we don't know how to set up Aladin chip again.
+	 */
+	// ddb_pci_reset_bus(); 
+
+	ddb_out32(DDB_BAR0, 0x00000008);
+
+	ddb_out32(DDB_BARC, 0xffffffff);
+	ddb_out32(DDB_BARB, 0xffffffff);
+	ddb_out32(DDB_BAR1, 0xffffffff);
+	ddb_out32(DDB_BAR2, 0xffffffff);
+	ddb_out32(DDB_BAR3, 0xffffffff);
+	ddb_out32(DDB_BAR4, 0xffffffff);
+	ddb_out32(DDB_BAR5, 0xffffffff);
+	ddb_out32(DDB_BAR6, 0xffffffff);
+	ddb_out32(DDB_BAR7, 0xffffffff);
+	ddb_out32(DDB_BAR8, 0xffffffff);
+
+	/* ----------- switch PCI1 to PCI CONFIG space  ------------ */
+	ddb_set_pdar(DDB_PCIW1, DDB_PCI_CONFIG_BASE, DDB_PCI_CONFIG_SIZE, 32, 0, 1);
+	ddb_set_pmr(DDB_PCIINIT1, DDB_PCICMD_CFG, 0x0, DDB_PCI_ACCESS_32);
+
+	/* ----- M1543 PCI setup ------ */
+
+	/* we know M1543 PCI-ISA controller is at addr:18 */
+	/* xxxx1010 makes USB at addr:13 and PMU at addr:14 */
+	*(volatile unsigned char *) 0xa8040072 &= 0xf0;
+	*(volatile unsigned char *) 0xa8040072 |= 0xa;
+
+	/* setup USB interrupt to IRQ 9, (bit 0:3 - 0001)
+	 * no IOCHRDY signal, (bit 7 - 1)
+	 * M1543C & M7101 VID and Subsys Device ID are read-only (bit 6 - 1)
+	 * Make USB Master INTAJ level to edge conversion (bit 4 - 1)
+	 */
+	*(unsigned char *) 0xa8040074 = 0xd1;
+
+	/* setup PMU(SCI to IRQ 10 (bit 0:3 - 0011)
+	 * SCI routing to IRQ 13 disabled (bit 7 - 1)
+	 * SCI interrupt level to edge conversion bypassed (bit 4 - 0)
+	 */
+	*(unsigned char *) 0xa8040076 = 0x83;
+
+	/* setup IDE controller
+	 * enable IDE controller (bit 6 - 1)
+	 * IDE IDSEL to be addr:24 (bit 4:5 - 11)
+	 * no IDE ATA Secondary Bus Signal Pad Control (bit 3 - 0)
+	 * no IDE ATA Primary Bus Signal Pad Control (bit 2 - 0)
+	 * primary IRQ is 14, secondary is 15 (bit 1:0 - 01
+	 */
+	// *(unsigned char*)0xa8040058 = 0x71;
+	// *(unsigned char*)0xa8040058 = 0x79;
+	// *(unsigned char*)0xa8040058 = 0x74;              // use SIRQ, primary tri-state
+	*(unsigned char *) 0xa8040058 = 0x75;	// primary tri-state
+
+#if 0
+	/* this is not necessary if M5229 does not use SIRQ */
+	*(unsigned char *) 0xa8040044 = 0x0d;	// primary to IRQ 14
+	*(unsigned char *) 0xa8040075 = 0x0d;	// secondary to IRQ 14
+#endif
+
+	/* enable IDE in the M5229 config register 0x50 (bit 0 - 1) */
+	/* M5229 IDSEL is addr:24; see above setting */
+	*(unsigned char *) 0xa9000050 |= 0x1;
+
+	/* enable bus master (bit 2)  and IO decoding  (bit 0) */
+	*(unsigned char *) 0xa9000004 |= 0x5;
+
+	/* enable native, copied from arch/ppc/k2boot/head.S */
+	/* TODO - need volatile, need to be portable */
+	*(unsigned char *) 0xa9000009 = 0xff;
+
+	/* ----- end of M1543 PCI setup ------ */
+
+	/* ----- reset on-board ether chip  ------ */
+	*((volatile u32 *) 0xa8020004) |= 1;	/* decode I/O */
+	*((volatile u32 *) 0xa8020010) = 0;	/* set BAR address */
+
+	/* send reset command */
+	*((volatile u32 *) 0xa6000000) = 1;	/* do a soft reset */
+
+	/* disable ether chip */
+	*((volatile u32 *) 0xa8020004) = 0;	/* disable any decoding */
+
+	/* put it into sleep */
+	*((volatile u32 *) 0xa8020040) = 0x80000000;
+
+	/* ----- end of reset on-board ether chip  ------ */
+
+	/* ----------- switch PCI1 back to PCI MEM space  ------------ */
+	ddb_set_pdar(DDB_PCIW1, DDB_PCI_MEM_BASE, DDB_PCI_MEM_SIZE, 32, 0, 1);
+	ddb_set_pmr(DDB_PCIINIT1, DDB_PCICMD_MEM, DDB_PCI_MEM_BASE, DDB_PCI_ACCESS_32);
+}