patch-2.3.99-pre1 linux/drivers/block/dtc2278.c

• Lines: 134
• Date: Wed Dec 31 16:00:00 1969
• Orig file: v2.3.51/linux/drivers/block/dtc2278.c
• Orig date: Sat Feb 26 22:31:43 2000

diff -u --recursive --new-file v2.3.51/linux/drivers/block/dtc2278.c linux/drivers/block/dtc2278.c
@@ -1,133 +0,0 @@
-/*
- *  linux/drivers/block/dtc2278.c		Version 0.02	Feb 10, 1996
- *
- *  Copyright (C) 1996  Linus Torvalds & author (see below)
- */
-
-#undef REALLY_SLOW_IO           /* most systems can safely undef this */
-
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/timer.h>
-#include <linux/mm.h>
-#include <linux/ioport.h>
-#include <linux/blkdev.h>
-#include <linux/hdreg.h>
-#include <linux/ide.h>
-
-#include <asm/io.h>
-
-#include "ide_modes.h"
-
-/*
- * Changing this #undef to #define may solve start up problems in some systems.
- */
-#undef ALWAYS_SET_DTC2278_PIO_MODE
-
-/*
- * From: andy@cercle.cts.com (Dyan Wile)
- *
- * Below is a patch for DTC-2278 - alike software-programmable controllers
- * The code enables the secondary IDE controller and the PIO4 (3?) timings on
- * the primary (EIDE). You may probably have to enable the 32-bit support to
- * get the full speed. You better get the disk interrupts disabled ( hdparm -u0
- * /dev/hd.. ) for the drives connected to the EIDE interface. (I get my
- * filesystem  corrupted with -u1, but under heavy disk load only :-)
- *
- * This card is now forced to use the "serialize" feature,
- * and irq-unmasking is disallowed.  If io_32bit is enabled,
- * it must be done for BOTH drives on each interface.
- *
- * This code was written for the DTC2278E, but might work with any of these:
- *
- * DTC2278S has only a single IDE interface.
- * DTC2278D has two IDE interfaces and is otherwise identical to the S version.
- * DTC2278E also has serial ports and a printer port
- * DTC2278EB: has onboard BIOS, and "works like a charm" -- Kent Bradford <kent@theory.caltech.edu>
- *
- * There may be a fourth controller type. The S and D versions use the
- * Winbond chip, and I think the E version does also.
- *
- */
-
-static void sub22 (char b, char c)
-{
-	int i;
-
-	for(i = 0; i < 3; ++i) {
-		inb(0x3f6);
-		outb_p(b,0xb0);
-		inb(0x3f6);
-		outb_p(c,0xb4);
-		inb(0x3f6);
-		if(inb(0xb4) == c) {
-			outb_p(7,0xb0);
-			inb(0x3f6);
-			return;	/* success */
-		}
-	}
-}
-
-static void tune_dtc2278 (ide_drive_t *drive, byte pio)
-{
-	unsigned long flags;
-
-	pio = ide_get_best_pio_mode(drive, pio, 4, NULL);
-
-	if (pio >= 3) {
-		save_flags(flags);	/* all CPUs */
-		cli();			/* all CPUs */
-		/*
-		 * This enables PIO mode4 (3?) on the first interface
-		 */
-		sub22(1,0xc3);
-		sub22(0,0xa0);
-		restore_flags(flags);	/* all CPUs */
-	} else {
-		/* we don't know how to set it back again.. */
-	}
-
-	/*
-	 * 32bit I/O has to be enabled for *both* drives at the same time.
-	 */
-	drive->io_32bit = 1;
-	HWIF(drive)->drives[!drive->select.b.unit].io_32bit = 1;
-}
-
-void __init init_dtc2278 (void)
-{
-	unsigned long flags;
-
-	__save_flags(flags);	/* local CPU only */
-	__cli();		/* local CPU only */
-	/*
-	 * This enables the second interface
-	 */
-	outb_p(4,0xb0);
-	inb(0x3f6);
-	outb_p(0x20,0xb4);
-	inb(0x3f6);
-#ifdef ALWAYS_SET_DTC2278_PIO_MODE
-	/*
-	 * This enables PIO mode4 (3?) on the first interface
-	 * and may solve start-up problems for some people.
-	 */
-	sub22(1,0xc3);
-	sub22(0,0xa0);
-#endif
-	__restore_flags(flags);	/* local CPU only */
-
-	ide_hwifs[0].serialized = 1;
-	ide_hwifs[1].serialized = 1;
-	ide_hwifs[0].chipset = ide_dtc2278;
-	ide_hwifs[1].chipset = ide_dtc2278;
-	ide_hwifs[0].tuneproc = &tune_dtc2278;
-	ide_hwifs[0].drives[0].no_unmask = 1;
-	ide_hwifs[0].drives[1].no_unmask = 1;
-	ide_hwifs[1].drives[0].no_unmask = 1;
-	ide_hwifs[1].drives[1].no_unmask = 1;
-	ide_hwifs[0].mate = &ide_hwifs[1];
-	ide_hwifs[1].mate = &ide_hwifs[0];
-	ide_hwifs[1].channel = 1;
-}