patch-2.3.49 linux/include/linux/digi1.h

• Lines: 101
• Date: Wed Dec 31 16:00:00 1969
• Orig file: v2.3.48/linux/include/linux/digi1.h
• Orig date: Tue May 13 22:41:18 1997

diff -u --recursive --new-file v2.3.48/linux/include/linux/digi1.h linux/include/linux/digi1.h
@@ -1,100 +0,0 @@
-/*          Definitions for DigiBoard ditty(1) command.                 */
-
-#if !defined(TIOCMODG)
-#define	TIOCMODG	('d'<<8) | 250		/* get modem ctrl state	*/
-#define	TIOCMODS	('d'<<8) | 251		/* set modem ctrl state	*/
-#endif
-
-#if !defined(TIOCMSET)
-#define	TIOCMSET	('d'<<8) | 252		/* set modem ctrl state	*/
-#define	TIOCMGET	('d'<<8) | 253		/* set modem ctrl state	*/
-#endif
-
-#if !defined(TIOCMBIC)
-#define	TIOCMBIC	('d'<<8) | 254		/* set modem ctrl state */
-#define	TIOCMBIS	('d'<<8) | 255		/* set modem ctrl state */
-#endif
-
-#if !defined(TIOCSDTR)
-#define	TIOCSDTR	('e'<<8) | 0		/* set DTR		*/
-#define	TIOCCDTR	('e'<<8) | 1		/* clear DTR		*/
-#endif
-
-/************************************************************************
- * Ioctl command arguments for DIGI parameters.
- ************************************************************************/
-#define DIGI_GETA	('e'<<8) | 94		/* Read params		*/
-
-#define DIGI_SETA	('e'<<8) | 95		/* Set params		*/
-#define DIGI_SETAW	('e'<<8) | 96		/* Drain & set params	*/
-#define DIGI_SETAF	('e'<<8) | 97		/* Drain, flush & set params */
-
-#define	DIGI_GETFLOW	('e'<<8) | 99		/* Get startc/stopc flow */
-						/* control characters 	 */
-#define	DIGI_SETFLOW	('e'<<8) | 100		/* Set startc/stopc flow */
-						/* control characters	 */
-#define	DIGI_GETAFLOW	('e'<<8) | 101		/* Get Aux. startc/stopc */
-						/* flow control chars 	 */
-#define	DIGI_SETAFLOW	('e'<<8) | 102		/* Set Aux. startc/stopc */
-						/* flow control chars	 */
-
-#define	DIGI_GETINFO	('e'<<8) | 103		/* Fill in digi_info */
-#define	DIGI_POLLER	('e'<<8) | 104		/* Turn on/off poller */
-#define	DIGI_INIT	('e'<<8) | 105		/* Allow things to run. */
-
-struct	digiflow_struct 
-{
-	unsigned char	startc;				/* flow cntl start char	*/
-	unsigned char	stopc;				/* flow cntl stop char	*/
-};
-
-typedef struct digiflow_struct digiflow_t;
-
-
-/************************************************************************
- * Values for digi_flags 
- ************************************************************************/
-#define DIGI_IXON	0x0001		/* Handle IXON in the FEP	*/
-#define DIGI_FAST	0x0002		/* Fast baud rates		*/
-#define RTSPACE		0x0004		/* RTS input flow control	*/
-#define CTSPACE		0x0008		/* CTS output flow control	*/
-#define DSRPACE		0x0010		/* DSR output flow control	*/
-#define DCDPACE		0x0020		/* DCD output flow control	*/
-#define DTRPACE		0x0040		/* DTR input flow control	*/
-#define DIGI_FORCEDCD	0x0100		/* Force carrier		*/
-#define	DIGI_ALTPIN	0x0200		/* Alternate RJ-45 pin config	*/
-#define	DIGI_AIXON	0x0400		/* Aux flow control in fep	*/
-
-
-/************************************************************************
- * Values for digiDload
- ************************************************************************/
-#define NORMAL  0
-#define PCI_CTL 1
-
-#define SIZE8  0
-#define SIZE16 1
-#define SIZE32 2
-
-/************************************************************************
- * Structure used with ioctl commands for DIGI parameters.
- ************************************************************************/
-struct digi_struct 
-{
-	unsigned short	digi_flags;		/* Flags (see above)	*/
-};
-
-typedef struct digi_struct digi_t;
-
-struct digi_info 
-{
-	unsigned long board;        /* Which board is this ? */
-	unsigned char status;       /* Alive or dead */
-	unsigned char type;         /* see epca.h */
-	unsigned char subtype;      /* For future XEM, XR, etc ... */
-	unsigned short numports;    /* Number of ports configured */
-	unsigned char *port;        /* I/O Address */
-	unsigned char *membase;     /* DPR Address */
-	unsigned char *version;     /* For future ... */
-	unsigned short windowData;  /* For future ... */
-} ;