patch-2.2.18 linux/arch/arm/kernel/hw-footbridge.c

Next file: linux/arch/arm/kernel/iic.c
Previous file: linux/arch/arm/kernel/hw-ebsa285.c
Back to the patch index
Back to the overall index

diff -u --new-file --recursive --exclude-from /usr/src/exclude v2.2.17/arch/arm/kernel/hw-footbridge.c linux/arch/arm/kernel/hw-footbridge.c
@@ -0,0 +1,951 @@
+/*
+ * arch/arm/kernel/hw-footbridge.c
+ *
+ * Footbridge-dependent machine fixup
+ *
+ * Copyright (C) 1998, 1999 Russell King, Phil Blundell
+ */
+#include <linux/config.h>
+#include <linux/module.h>
+#include <linux/sched.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+#include <linux/ptrace.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/smp.h>
+#include <linux/mm.h>
+#include <linux/init.h>
+
+#include <asm/dec21285.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/leds.h>
+#include <asm/system.h>
+
+#define IRDA_IO_BASE		0x180
+#define ETHER10_IO_BASE		0x301
+#define GP1_IO_BASE		0x338
+#define GP2_IO_BASE		0x33a
+#define DEC21143_IO_BASE	0x401
+#define DEC21143_MEM_BASE	0x00800000
+#define CYBER2000_MEM_BASE	0x01000000
+
+int	have_isa_bridge;
+
+extern int setup_arm_irq(int, struct irqaction *);
+extern void pci_set_cmd(struct pci_dev *dev, unsigned short clear, unsigned short set);
+extern void pci_set_base_addr(struct pci_dev *dev, int idx, unsigned int addr);
+extern void pci_set_irq_line(struct pci_dev *dev, unsigned int irq);
+extern void (*kd_mksound)(unsigned int hz, unsigned int ticks);
+
+#ifdef CONFIG_PCI
+
+static int irqmap_ebsa[] __initdata = { IRQ_IN1, IRQ_IN0, IRQ_PCI, IRQ_IN3 };
+
+__initfunc(static int ebsa_irqval(struct pci_dev *dev))
+{
+	unsigned char pin;
+	
+	pcibios_read_config_byte(dev->bus->number,
+				 dev->devfn,
+				 PCI_INTERRUPT_PIN,
+				 &pin);
+	
+	return irqmap_ebsa[(PCI_SLOT(dev->devfn) + pin) & 3];
+}
+
+#ifdef CONFIG_CATS
+static int irqmap_cats[] __initdata = { IRQ_PCI, IRQ_IN0, IRQ_IN1, IRQ_IN3 };
+
+__initfunc(static int cats_irqval(struct pci_dev *dev))
+{
+	if (dev->irq >= 128)
+		return 16 + (dev->irq & 0x1f);
+
+	switch (dev->irq) {
+	case 1:
+	case 2:
+	case 3:
+	case 4:
+		return irqmap_cats[dev->irq - 1];
+	case 0:
+		return 0;
+	}
+
+	printk("PCI: device %02x:%02x has unknown irq line %x\n",
+	       dev->bus->number, dev->devfn, dev->irq);
+	return 0;
+}
+#endif
+
+__initfunc(void pcibios_fixup_ebsa285(struct pci_dev *dev))
+{
+	/* Latency timer of 32 */
+	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 32);
+
+	/* 32-byte cache line size */
+	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, 8);
+
+	/* Set SysErr enable, Parity enable */
+	pci_set_cmd(dev, 0, PCI_COMMAND_FAST_BACK | PCI_COMMAND_SERR | PCI_COMMAND_PARITY);
+
+	/* If this device is an ISA bridge, set the
+	 * have_isa_bridge flag.  We will then go looking
+	 * for things like keyboard, etc
+	 */
+	if ((dev->class >> 8) == PCI_CLASS_BRIDGE_ISA ||
+	    (dev->class >> 8) == PCI_CLASS_BRIDGE_EISA)
+		have_isa_bridge = !0;
+
+	/* sort out the irq mapping for this device */
+	switch (machine_arch_type) {
+	case MACH_TYPE_EBSA285:
+		dev->irq = ebsa_irqval(dev);
+		/* Turn on bus mastering - boot loader doesn't
+		 * - perhaps it should! - dag
+		 */
+		pci_set_cmd(dev, 0, PCI_COMMAND_MASTER);
+		break;
+
+#ifdef CONFIG_CATS
+	case MACH_TYPE_CATS:
+		dev->irq = cats_irqval(dev);
+		/* Turn on bus mastering - boot loader doesn't
+		 * - perhaps it should! - dag
+		 */
+		pci_set_cmd(dev, 0, PCI_COMMAND_MASTER);
+		break;
+#endif
+#ifdef CONFIG_ARCH_NETWINDER
+	case MACH_TYPE_NETWINDER:
+		/* disable ROM */
+		pci_write_config_dword(dev, PCI_ROM_ADDRESS, 0);
+
+#define DEV(v,d) ((v)<<16|(d))
+		switch (DEV(dev->vendor, dev->device)) {
+		/* Ether 100 */
+		case DEV(PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_21142):
+			pci_set_base_addr(dev, 0, DEC21143_IO_BASE);
+			pci_set_base_addr(dev, 1, DEC21143_MEM_BASE);
+			pci_set_cmd(dev, 0, PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY | PCI_COMMAND_IO);
+			/* Put the chip to sleep in case the driver isn't loaded */
+			pci_write_config_dword(dev, 0x40, 0x80000000);
+			dev->irq = IRQ_NETWINDER_ETHER100;
+			break;
+
+		/* Ether 10 */
+		case DEV(PCI_VENDOR_ID_WINBOND2,0x5a5a):
+			pci_set_base_addr(dev, 0, ETHER10_IO_BASE);
+			pci_set_cmd(dev, PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY, PCI_COMMAND_IO);
+			dev->irq = IRQ_NETWINDER_ETHER10;
+			break;
+
+		/* ISA bridge */
+		case DEV(PCI_VENDOR_ID_WINBOND,PCI_DEVICE_ID_WINBOND_83C553):
+			pci_set_base_addr(dev, 0, 0);
+			pci_set_cmd(dev, PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY, PCI_COMMAND_IO);
+			/*
+			 * Enable all memory requests from ISA to be channeled to PCI
+			 */
+			pci_write_config_byte(dev, 0x48, 255);
+			/*
+			 * Disable ping-pong (as per errata)
+			 */
+			pci_write_config_byte(dev, 0x42, 0);
+			/*
+			 * Enable PCI packet retry
+			 */
+			pci_write_config_byte(dev, 0x40, 0x22);
+			/*
+			 * Do not use PCI CPU park enable, park on
+			 * last master, disable GAT bit
+			 */
+			pci_write_config_byte(dev, 0x83, 0x02);
+			/*
+			 * Default rotating priorities
+			 */
+			pci_write_config_byte(dev, 0x80, 0xe0);
+			/*
+			 * Rotate bank 4
+			 */
+			pci_write_config_byte(dev, 0x81, 0x01);
+			break;
+
+		/* IDE */
+		case DEV(PCI_VENDOR_ID_WINBOND,PCI_DEVICE_ID_WINBOND_82C105):
+			pci_set_base_addr(dev, 0, 0x1f1);
+			pci_set_base_addr(dev, 1, 0x3f5);
+			pci_set_base_addr(dev, 2, 0x171);
+			pci_set_base_addr(dev, 3, 0x375);
+			pci_set_base_addr(dev, 4, 0xe801);
+			pci_set_cmd(dev, PCI_COMMAND_MEMORY, PCI_COMMAND_MASTER | PCI_COMMAND_IO);
+			dev->irq = IRQ_ISA_HARDDISK1;
+			break;
+
+		/* VGA */
+		case DEV(PCI_VENDOR_ID_INTERG,0x2000):
+			pci_set_base_addr(dev, 0, CYBER2000_MEM_BASE);
+			pci_set_cmd(dev, PCI_COMMAND_MASTER, PCI_COMMAND_IO | PCI_COMMAND_MEMORY);
+			dev->irq = IRQ_NETWINDER_VGA;
+			break;
+		}
+#endif
+	}
+}
+
+static inline void
+report_pci_dev_error(void)
+{
+	struct pci_dev *dev;
+
+	for (dev = pci_devices; dev; dev = dev->next) {
+		unsigned short status;
+
+		pci_read_config_word(dev, PCI_STATUS, &status);
+		if (status & 0xf900) {
+			printk(KERN_DEBUG "PCI: [%04X:%04X] status = %X\n",
+				dev->vendor, dev->device, status);
+
+			pci_write_config_word(dev, PCI_STATUS, status & 0xf900);
+		}
+	}
+}
+#else
+#define report_pci_dev_error()
+#endif
+
+/*
+ * Warn on PCI errors.  Please report any occurances!
+ */
+static void
+irq_pci_err(int irq, void *dev_id, struct pt_regs *regs)
+{
+	static unsigned long next_warn;
+	unsigned long cmd       = *CSR_PCICMD & 0x0000ffff;
+	unsigned long ctrl      = (*CSR_SA110_CNTL) & 0xffffde07;
+	unsigned long irqstatus = *CSR_IRQ_RAWSTATUS;
+	int warn = time_after_eq(jiffies, next_warn);
+
+	ctrl |= SA110_CNTL_DISCARDTIMER;
+
+	if (warn) {
+		next_warn = jiffies + 3 * HZ / 100;
+		printk(KERN_DEBUG "PCI: ");
+	}
+
+	if (irqstatus & (1 << 31)) {
+		if (warn)
+			printk("parity error ");
+		cmd |= 1 << 31;
+	}
+
+	if (irqstatus & (1 << 30)) {
+		if (warn)
+			printk("target abort ");
+		cmd |= 1 << 28;
+	}
+
+	if (irqstatus & (1 << 29)) {
+		if (warn)
+			printk("master abort ");
+		cmd |= 1 << 29;
+	}
+
+	if (irqstatus & (1 << 28)) {
+		if (warn)
+			printk("data parity error ");
+		cmd |= 1 << 24;
+	}
+
+	if (irqstatus & (1 << 27)) {
+		if (warn)
+			printk("discard timer expired ");
+		ctrl &= ~SA110_CNTL_DISCARDTIMER;
+	}
+
+	if (irqstatus & (1 << 23)) {
+		if (warn)
+			printk("system error ");
+		ctrl |= SA110_CNTL_RXSERR;
+	}
+
+	if (warn)
+		printk("pc=[<%08lX>]\n", instruction_pointer(regs));
+
+	report_pci_dev_error();
+
+	*CSR_PCICMD = cmd;
+	*CSR_SA110_CNTL = ctrl;
+}
+
+static struct irqaction irq_pci_error = {
+	irq_pci_err, SA_INTERRUPT, 0, "PCI error", NULL, NULL
+};
+
+__initfunc(void pcibios_init_ebsa285(void))
+{
+	setup_arm_irq(IRQ_PCI_ERR, &irq_pci_error);
+}
+
+/*
+ * Netwinder stuff
+ */
+#ifdef CONFIG_ARCH_NETWINDER
+
+/*
+ * Winbond WB83977F accessibility stuff
+ */
+static inline void wb977_open(void)
+{
+	outb(0x87, 0x370);
+	outb(0x87, 0x370);
+}
+
+static inline void wb977_close(void)
+{
+	outb(0xaa, 0x370);
+}
+
+static inline void wb977_wb(int reg, int val)
+{
+	outb(reg, 0x370);
+	outb(val, 0x371);
+}
+
+static inline void wb977_ww(int reg, int val)
+{
+	outb(reg, 0x370);
+	outb(val >> 8, 0x371);
+	outb(reg + 1, 0x370);
+	outb(val, 0x371);
+}
+
+#define wb977_device_select(dev)	wb977_wb(0x07, dev)
+#define wb977_device_disable()		wb977_wb(0x30, 0x00)
+#define wb977_device_enable()		wb977_wb(0x30, 0x01)
+
+/*
+ * This is a lock for accessing ports GP1_IO_BASE and GP2_IO_BASE
+ */
+spinlock_t __netwinder_data gpio_lock = SPIN_LOCK_UNLOCKED;
+
+static unsigned int __netwinder_data current_gpio_op = 0;
+static unsigned int __netwinder_data current_gpio_io = 0;
+static unsigned int __netwinder_data current_cpld = 0;
+
+void __netwinder_text gpio_modify_op(int mask, int set)
+{
+	unsigned int new_gpio, changed;
+
+	new_gpio = (current_gpio_op & ~mask) | set;
+	changed = new_gpio ^ current_gpio_op;
+	current_gpio_op = new_gpio;
+
+	if (changed & 0xff)
+		outb(new_gpio, GP1_IO_BASE);
+	if (changed & 0xff00)
+		outb(new_gpio >> 8, GP2_IO_BASE);
+}
+
+static inline void __gpio_modify_io(int mask, int in)
+{
+	unsigned int new_gpio, changed;
+	int port;
+
+	new_gpio = (current_gpio_io & ~mask) | in;
+	changed = new_gpio ^ current_gpio_io;
+	current_gpio_io = new_gpio;
+
+	changed >>= 1;
+	new_gpio >>= 1;
+
+	wb977_device_select(7);
+
+	for (port = 0xe1; changed && port < 0xe8; changed >>= 1) {
+		wb977_wb(port, new_gpio & 1);
+
+		port += 1;
+		new_gpio >>= 1;
+	}
+
+	wb977_device_select(8);
+
+	for (port = 0xe8; changed && port < 0xec; changed >>= 1) {
+		wb977_wb(port, new_gpio & 1);
+
+		port += 1;
+		new_gpio >>= 1;
+	}
+}
+
+void __netwinder_text gpio_modify_io(int mask, int in)
+{
+	/* Open up the SuperIO chip */
+	wb977_open();
+
+	__gpio_modify_io(mask, in);
+
+	/* Close up the EFER gate */
+	wb977_close();
+}
+
+int __netwinder_text gpio_read(void)
+{
+	return inb(GP1_IO_BASE) | inb(GP2_IO_BASE) << 8;
+}
+
+/*
+ * Initialise the Winbond W83977F global registers
+ */
+static inline void wb977_init_global(void)
+{
+	/*
+	 * Enable R/W config registers
+	 */
+	wb977_wb(0x26, 0x40);
+
+	/*
+	 * Power down FDC (not used)
+	 */
+	wb977_wb(0x22, 0xfe);
+
+	/*
+	 * GP12, GP11, CIRRX, IRRXH, GP10
+	 */
+	wb977_wb(0x2a, 0xc1);
+
+	/*
+	 * GP23, GP22, GP21, GP20, GP13
+	 */
+	wb977_wb(0x2b, 0x6b);
+
+	/*
+	 * GP17, GP16, GP15, GP14
+	 */
+	wb977_wb(0x2c, 0x55);
+}
+
+/*
+ * Initialise the Winbond W83977F printer port
+ */
+static inline void wb977_init_printer(void)
+{
+	wb977_device_select(1);
+
+	/*
+	 * mode 1 == EPP
+	 */
+	wb977_wb(0xf0, 0x01);
+}
+
+/*
+ * Initialise the Winbond W83977F keyboard controller
+ */
+static inline void wb977_init_keyboard(void)
+{
+	wb977_device_select(5);
+
+	/*
+	 * Keyboard controller address
+	 */
+	wb977_ww(0x60, 0x0060);
+	wb977_ww(0x62, 0x0064);
+
+	/*
+	 * Keyboard IRQ 1, active high, edge trigger
+	 */
+	wb977_wb(0x70, 1);
+	wb977_wb(0x71, 0x02);
+
+	/*
+	 * Mouse IRQ 5, active high, edge trigger
+	 */
+	wb977_wb(0x72, 5);
+	wb977_wb(0x73, 0x02);
+
+	/*
+	 * KBC 8MHz
+	 */
+	wb977_wb(0xf0, 0x40);
+
+	/*
+	 * Enable device
+	 */
+	wb977_device_enable();
+}
+
+/*
+ * Initialise the Winbond W83977F Infra-Red device
+ */
+static inline void wb977_init_irda(void)
+{
+	wb977_device_select(6);
+
+	/*
+	 * IR base address
+	 */
+	wb977_ww(0x60, IRDA_IO_BASE);
+
+	/*
+	 * IRDA IRQ 6, active high, edge trigger
+	 */
+	wb977_wb(0x70, 6);
+	wb977_wb(0x71, 0x02);
+
+	/*
+	 * RX DMA - ISA DMA 0
+	 */
+	wb977_wb(0x74, 0x00);
+
+	/*
+	 * TX DMA - Disable Tx DMA
+	 */
+	wb977_wb(0x75, 0x04);
+
+	/*
+	 * Append CRC, Enable bank selection
+	 */
+	wb977_wb(0xf0, 0x03);
+
+	/*
+	 * Enable device
+	 */
+	wb977_device_enable();
+}
+
+/*
+ * Initialise Winbond W83977F general purpose IO
+ */
+static inline void wb977_init_gpio(void)
+{
+	unsigned long flags;
+
+	/*
+	 * Set up initial I/O definitions
+	 */
+	current_gpio_io = -1;
+	__gpio_modify_io(-1, GPIO_DONE | GPIO_WDTIMER);
+
+	wb977_device_select(7);
+
+	/*
+	 * Group1 base address
+	 */
+	wb977_ww(0x60, GP1_IO_BASE);
+	wb977_ww(0x62, 0);
+	wb977_ww(0x64, 0);
+
+	/*
+	 * GP10 (Orage button) IRQ 10, active high, edge trigger
+	 */
+	wb977_wb(0x70, 10);
+	wb977_wb(0x71, 0x02);
+
+	/*
+	 * GP10: Debounce filter enabled, IRQ, input
+	 */
+	wb977_wb(0xe0, 0x19);
+
+	/*
+	 * Enable Group1
+	 */
+	wb977_device_enable();
+
+	wb977_device_select(8);
+
+	/*
+	 * Group2 base address
+	 */
+	wb977_ww(0x60, GP2_IO_BASE);
+
+	/*
+	 * Clear watchdog timer regs
+	 *  - timer disable
+	 */
+	wb977_wb(0xf2, 0x00);
+
+	/*
+	 *  - disable LED, no mouse nor keyboard IRQ
+	 */
+	wb977_wb(0xf3, 0x00);
+
+	/*
+	 *  - timer counting, disable power LED, disable timeouot
+	 */
+	wb977_wb(0xf4, 0x00);
+
+	/*
+	 * Enable group2
+	 */
+	wb977_device_enable();
+
+	/*
+	 * Set Group1/Group2 outputs
+	 */
+	spin_lock_irqsave(&gpio_lock, flags);
+	gpio_modify_op(-1, GPIO_RED_LED | GPIO_FAN);
+	spin_unlock_irqrestore(&gpio_loc, flags);
+}
+
+/*
+ * Initialise the Winbond W83977F chip.
+ */
+__initfunc(static void wb977_init(void))
+{
+	request_region(0x370, 2, "W83977AF configuration");
+
+	/*
+	 * Open up the SuperIO chip
+	 */
+	wb977_open();
+
+	/*
+	 * Initialise the global registers
+	 */
+	wb977_init_global();
+
+	/*
+	 * Initialise the various devices in
+	 * the multi-IO chip.
+	 */
+	wb977_init_printer();
+	wb977_init_keyboard();
+	wb977_init_irda();
+	wb977_init_gpio();
+
+	/*
+	 * Close up the EFER gate
+	 */
+	wb977_close();
+}
+
+void __netwinder_text cpld_modify(int mask, int set)
+{
+	int msk;
+
+	current_cpld = (current_cpld & ~mask) | set;
+
+	gpio_modify_io(GPIO_DATA, 0);
+	gpio_modify_op(GPIO_IOLOAD, 0);
+
+	for (msk = 8; msk; msk >>= 1) {
+		int bit = current_cpld & msk;
+
+		gpio_modify_op(GPIO_DATA | GPIO_IOCLK, bit ? GPIO_DATA : 0);
+		gpio_modify_op(GPIO_IOCLK, GPIO_IOCLK);
+	}
+
+	gpio_modify_op(GPIO_IOCLK|GPIO_DATA, 0);
+	gpio_modify_op(GPIO_IOLOAD|GPIO_DSCLK, GPIO_IOLOAD|GPIO_DSCLK);
+	gpio_modify_op(GPIO_IOLOAD, 0);
+}
+
+__initfunc(static void cpld_init(void))
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&gpio_lock, flags);
+	cpld_modify(-1, CPLD_UNMUTE | 4);
+	spin_unlock_irqrestore(&gpio_lock, flags);
+}
+
+static unsigned char rwa_unlock[] __initdata =
+{ 0x00, 0x00, 0x6a, 0xb5, 0xda, 0xed, 0xf6, 0xfb, 0x7d, 0xbe, 0xdf, 0x6f, 0x37, 0x1b,
+  0x0d, 0x86, 0xc3, 0x61, 0xb0, 0x58, 0x2c, 0x16, 0x8b, 0x45, 0xa2, 0xd1, 0xe8, 0x74,
+  0x3a, 0x9d, 0xce, 0xe7, 0x73, 0x39 };
+
+#ifndef DEBUG
+#define dprintk if (0) printk
+#else
+#define dprintk printk
+#endif
+
+#define WRITE_RWA(r,v) do { outb((r), 0x279); outb((v), 0xa79); } while (0)
+
+static inline void rwa010_unlock(void)
+{
+	int i;
+
+	WRITE_RWA(2, 2);
+	mdelay(10);
+
+	for (i = 0; i < sizeof(rwa_unlock); i++)
+		outb(rwa_unlock[i], 0x279);
+}
+
+static inline void rwa010_read_ident(void)
+{
+	unsigned char si[9];
+	int i, j;
+
+	WRITE_RWA(3, 0);
+	WRITE_RWA(0, 128);
+
+	outb(1, 0x279);
+
+	mdelay(10);
+
+	dprintk("Identifier: ");
+	for (i = 0; i < 9; i++) {
+		si[i] = 0;
+		for (j = 0; j < 8; j++) {
+			int bit;
+			mdelay(1);
+			inb(0x203);
+			mdelay(1);
+			bit = inb(0x203);
+			dprintk("%02X ", bit);
+			si[i] |= bit << j;
+		}
+		mdelay(10);
+		dprintk("%02X ", si[i]);
+	}
+	dprintk("\n");
+}
+
+static inline void rwa010_global_init(void)
+{
+	WRITE_RWA(6, 2);	// Assign a card no = 2
+
+	dprintk("Card no = %d\n", inb(0x203));
+
+	WRITE_RWA(7, 3);
+	WRITE_RWA(0x30, 0);
+
+	WRITE_RWA(7, 4);
+	WRITE_RWA(0x30, 0);
+
+	WRITE_RWA(7, 2);
+	WRITE_RWA(0x30, 0);
+}
+
+static inline void rwa010_game_port_init(void)
+{
+	int i;
+
+	WRITE_RWA(7, 5);
+
+	dprintk("Slider base: ");
+	WRITE_RWA(0x61, 1);
+	i = inb(0x203);
+
+	WRITE_RWA(0x60, 2);
+	dprintk("%02X%02X (201)\n", inb(0x203), i);
+
+	WRITE_RWA(0x30, 1);
+}
+
+static inline void rwa010_waveartist_init(int base, int irq, int dma)
+{
+	int i;
+
+	WRITE_RWA(7, 0);
+
+	dprintk("WaveArtist base: ");
+	WRITE_RWA(0x61, base);
+	i = inb(0x203);
+
+	WRITE_RWA(0x60, base >> 8);
+	dprintk("%02X%02X (%X),", inb(0x203), i, base);
+
+	WRITE_RWA(0x70, irq);
+	dprintk(" irq: %d (%d),", inb(0x203), irq);
+
+	WRITE_RWA(0x74, dma);
+	dprintk(" dma: %d (%d)\n", inb(0x203), dma);
+
+	WRITE_RWA(0x30, 1);
+}
+
+static inline void rwa010_soundblaster_init(int sb_base, int al_base, int irq, int dma)
+{
+	int i;
+
+	WRITE_RWA(7, 1);
+
+	dprintk("SoundBlaster base: ");
+	WRITE_RWA(0x61, sb_base);
+	i = inb(0x203);
+
+	WRITE_RWA(0x60, sb_base >> 8);
+	dprintk("%02X%02X (%X),", inb(0x203), i, sb_base);
+
+	dprintk(" irq: ");
+	WRITE_RWA(0x70, irq);
+	dprintk("%d (%d),", inb(0x203), irq);
+
+	dprintk(" 8-bit DMA: ");
+	WRITE_RWA(0x74, dma);
+	dprintk("%d (%d)\n", inb(0x203), dma);
+
+	dprintk("AdLib base: ");
+	WRITE_RWA(0x63, al_base);
+	i = inb(0x203);
+
+	WRITE_RWA(0x62, al_base >> 8);
+	dprintk("%02X%02X (%X)\n", inb(0x203), i, al_base);
+
+	WRITE_RWA(0x30, 1);
+}
+
+static void rwa010_soundblaster_reset(void)
+{
+	int i;
+
+	outb(1, 0x226);
+	udelay(3);
+	outb(0, 0x226);
+
+	for (i = 0; i < 5; i++) {
+		if (inb(0x22e) & 0x80)
+			break;
+		mdelay(1);
+	}
+	if (i == 5)
+		printk("SoundBlaster: DSP reset failed\n");
+
+	dprintk("SoundBlaster DSP reset: %02X (AA)\n", inb(0x22a));
+
+	for (i = 0; i < 5; i++) {
+		if ((inb(0x22c) & 0x80) == 0)
+			break;
+		mdelay(1);
+	}
+
+	if (i == 5)
+		printk("SoundBlaster: DSP not ready\n");
+	else {
+		outb(0xe1, 0x22c);
+
+		dprintk("SoundBlaster DSP id: ");
+		i = inb(0x22a);
+		udelay(1);
+		i |= inb(0x22a) << 8;
+		dprintk("%04X\n", i);
+
+		for (i = 0; i < 5; i++) {
+			if ((inb(0x22c) & 0x80) == 0)
+				break;
+			mdelay(1);
+		}
+
+		if (i == 5)
+			printk("SoundBlaster: could not turn speaker off\n");
+
+		outb(0xd3, 0x22c);
+	}
+
+	/* turn on OPL3 */
+	outb(5, 0x38a);
+	outb(1, 0x38b);
+}
+
+__initfunc(static void rwa010_init(void))
+{
+	rwa010_unlock();
+	rwa010_read_ident();
+	rwa010_global_init();
+	rwa010_game_port_init();
+	rwa010_waveartist_init(0x250, 3, 7);
+	rwa010_soundblaster_init(0x220, 0x388, 3, 1);
+	rwa010_soundblaster_reset();
+}
+
+EXPORT_SYMBOL(gpio_lock);
+EXPORT_SYMBOL(gpio_modify_op);
+EXPORT_SYMBOL(gpio_modify_io);
+EXPORT_SYMBOL(cpld_modify);
+
+#endif
+
+#ifdef CONFIG_LEDS
+#define DEFAULT_LEDS	0
+#else
+#define DEFAULT_LEDS	GPIO_GREEN_LED
+#endif
+
+/*
+ * CATS stuff
+ */
+#ifdef CONFIG_CATS
+
+#define CONFIG_PORT	0x370
+#define INDEX_PORT	(CONFIG_PORT)
+#define DATA_PORT	(CONFIG_PORT + 1)
+
+static void __init cats_hw_init(void)
+{
+	/* Set Aladdin to CONFIGURE mode */
+	outb(0x51, CONFIG_PORT);
+	outb(0x23, CONFIG_PORT);
+
+	/* Select logical device 3 */
+	outb(0x07, INDEX_PORT);
+	outb(0x03, DATA_PORT);
+
+	/* Set parallel port to DMA channel 3, ECP+EPP1.9, 
+	   enable EPP timeout */
+	outb(0x74, INDEX_PORT);
+	outb(0x03, DATA_PORT);
+	
+	outb(0xf0, INDEX_PORT);
+	outb(0x0f, DATA_PORT);
+
+	outb(0xf1, INDEX_PORT);
+	outb(0x07, DATA_PORT);
+
+	/* Select logical device 4 */
+	outb(0x07, INDEX_PORT);
+	outb(0x04, DATA_PORT);
+
+	/* UART1 high speed mode */
+	outb(0xf0, INDEX_PORT);
+	outb(0x02, DATA_PORT);
+
+	/* Select logical device 5 */
+	outb(0x07, INDEX_PORT);
+	outb(0x05, DATA_PORT);
+
+	/* UART2 high speed mode */
+	outb(0xf0, INDEX_PORT);
+	outb(0x02, DATA_PORT);
+
+	/* Set Aladdin to RUN mode */
+	outb(0xbb, CONFIG_PORT);
+}
+
+#endif
+
+__initfunc(void hw_init(void))
+{
+	extern void register_isa_ports(unsigned int, unsigned int, 
+				       unsigned int);
+	register_isa_ports(DC21285_PCI_MEM, DC21285_PCI_IO, 0);
+#ifdef CONFIG_ARCH_NETWINDER
+	/*
+	 * this ought to have a better home...
+	 * Since this calls the above routines, which are
+	 * compiled only if CONFIG_ARCH_NETWINDER is set,
+	 * these should only be parsed by the compiler
+	 * in the same circumstance.
+	 */
+	if (machine_is_netwinder()) {
+		unsigned long flags;
+
+		wb977_init();
+		cpld_init();
+		rwa010_init();
+
+		spin_lock_irqsave(&gpio_lock, flags);
+		gpio_modify_op(GPIO_RED_LED|GPIO_GREEN_LED, DEFAULT_LEDS);
+		spin_unlock_irqrestore(&gpio_lock, flags);
+	}
+#endif
+
+	if (machine_is_cats())
+		cats_hw_init();
+
+	leds_event(led_start);
+}

FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)